Troy-Bilt TB4000 manual Owners Warranty Responsibilities, Manufacturers Warranty Coverage

Page 27

Section 9

Warranty

CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OBLIGATIONS

The California Air Resources Board and MTD Southwest Inc (MTD), are pleased to explain the emis- sion control system warranty on your 2000 and later small off-road engine. In California, new small off-road engines must be designed, built and equipped to meet the State's stringent anti-smog standards. MTD must warrant the emission control system on your small off- road engine for the periods of time listed below provid- ed there has been no abuse, neglect or improper main- tenance of your small off-road engine.

Your emission control system may include parts such as the carburetor or fuel injection system, the ignition system, and catalytic converter. Also included may be hoses, belts, connectors and other emission-related assemblies.

Where a warrantable condition exists, MTD will repair your small off-road engine at no cost to you including diagnosis, parts and labor.

The 2000 and later small off-road engines are warrant- ed for two years. If any emission-related part on your engine is defective, the part will be repaired or replaced by MTD.

OWNER'S WARRANTY RESPONSIBILITIES:

•As the small off-road engine owner, you are responsible for the performance of the required maintenance listed in your operator's manual. MTD recommends that you retain all receipts covering maintenance on your small off-road engine, but MTD cannot deny warranty solely for the lack of receipts or for your failure to ensure the

performance of all scheduled maintenance.

•As the small off-road engine owner, you should how- ever be aware that MTD may deny you warranty cov- erage if your small off-road engine or a part has failed due to abuse, neglect, improper maintenance or unapproved modifications.

•You are responsible for presenting your small off-road engine to a MTD Authorized Service Center as soon as a problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you should call 1-800-345-8746.

MANUFACTURER'S WARRANTY COVERAGE:

•The warranty period begins on the date the engine or equipment is delivered to the retail purchaser.

•The manufacturer warrants to the initial owner and each subsequent purchaser, that the engine is free from defects in material and workmanship which cause the failure of a warranted part for a period of two years.

•Repair or replacement of warranted part will be per- formed at no charge to the owner at an Authorized MTD Service Center. For the nearest location, please contact MTD at: 1-800-345-8746.

•Any warranted part which is not scheduled for replacement, as required maintenance which is scheduled only for regular inspection to the effect of "Repair or replace as necessary" is warranted for the warranty period. Any warranted part which is sched- uled for replacement as required maintenance will be warranted for the period of time up to the first sched- uled replacement point for that part.

•The owner will not be charged for diagnostic labor which leads to the determination that a warranted part is defective, if the diagnostic work is performed at an Authorized MTD Service Center.

•The manufacturer is liable for damages to other engine components caused by the failure of a warranted part still under warranty.

•Failures caused by abuse, neglect or improper maintenance are not covered under warranty.

•The use of add-on or modified parts can be grounds for disallowing a warranty claim. The manufacturer is not liable to cover failures or warranted parts caused by the use of add-on or modified parts.

•In order to file a claim, go to your nearest Authorized MTD Service Center. Warranty services or repairs will be provided at all Authorized MTD Service Centers.

•Any manufacturer approved replacement part may be used in the performance of any warranty mainte- nance or repair of emission related parts and will be provided without charge to the owner. Any replace- ment part that is equivalent in performance or dura- bility may be used in non-warranty maintenance or repair and will not reduce the warranty obligations of the manufacturer.

•The following components are included in the emis- sion related warranty of the engine, air filter, carbure- tor, primer, fuel lines, fuel pick up/fuel filter, ignition module, spark plug and muffler.

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Owner/Operator Manual Cycle Trimmer Brush Cutter Introduction Table of ContentsAccessory 182153 Spark Arrestor Kit Service InformationBefore Operating SafetySymbol Meaning Safety Warnings for GAS TrimmersWhile Operating with Cutting Blade While OperatingFor Service INFORMATION, Call Safety and International SymbolsOther Safety Warnings Symbol Meaning Safety Alert SymbolThrown Objects and Rotating Cutter can Cause Severe Injury Symbol Meaning Unleaded FuelTRIMMER/BRUSH Cutter Safety OILApplications Know Your UnitAdjusting AssemblyInstalling and Adjusting the J-HANDLE InstallingRemove the Cutting Attachment Shield Installing the HarnessRemoving and Installing Cutting Attachment Shield Remove the Cutting Attachment and Install the Cutting BladeRemove the Cutting Attachment Install the Cutting Attachment Remove the Cutting Blade and Install the Cutting AttachmentOil and Fuel Recommended OIL TypeRecommended Fuel Type Operation Fueling UnitStarting Instructions Engine Re-Start Warm Engine With Fuel Stopping InstructionsAdjusting Trimming Line Length Holding the TrimmerTips for Best Trimming Results Using the Cutting Blade Decorative TrimmingCutting Blade Operating Tips Line Installation MaintenanceMaintenance Schedule When Maintenance Needed GO toGo To for Membrane Line Installation Single Line InstallationChanging the OIL Installing a Prewound ReelReplacement Parts Checking the OIL LevelCleaning the Air Filter AIR Filter MaintenanceCheck Fuel Carburetor AdjustmentOil and Fuel, Recommended Fuel Clean Air Filter Rocker ARM ClearanceReplacing the Spark Plug Long Term Storage ACCESSORIES/REPLACEMENT PartsCleaning StorageU S E T I O N TroubleshootingSpecifications 200-10,000 rpmInch 0.655 mm Warranty Owners Warranty ResponsibilitiesManufacturers Warranty Coverage MTD Southwest Inc

TB4000 specifications

The Troy-Bilt TB4000 is a versatile and reliable workhorse designed for homeowners and landscapers alike. This compact tiller blends power, efficiency, and user-friendly features, making it an indispensable tool for garden enthusiasts looking to cultivate and maintain their soil.

One of the standout features of the TB4000 is its robust engine. Equipped with a 4-cycle, 24.5cc engine, it delivers ample power to tackle tough soil conditions. This engine provides reliable performance while being easy to start thanks to its user-friendly recoil start mechanism. The four-stroke design eliminates the need for mixing fuel and oil, simplifying maintenance.

The TB4000 boasts a unique tilling capability that makes it suitable for a variety of gardening tasks. It features a 12-inch tilling width and adjustable tilling depth, allowing users to customize their tilling experience. Whether preparing a new garden bed or cultivating existing soil, the TB4000 can handle it with ease.

Durability is another important aspect of the TB4000's design. Its heavy-duty steel tines are built to withstand rigorous use and ensure longevity. The tiller is equipped with a front-mounted transport wheel, which makes it easy to maneuver from one location to another without straining the back or arms.

User comfort is also a major consideration in the design of the TB4000. The tiller features an ergonomic handle that can be adjusted for height, reducing strain during operation. Additionally, its lightweight design aids in overall control and ease of use.

For added convenience, the TB4000 offers a variety of tilling settings. It includes a forward-rotating tine mechanism, ideal for breaking up hard soil, while its adjustable speed allows for fine-tuning based on the task.

In terms of technology, the Troy-Bilt TB4000 comes equipped with enhancements that optimize performance. Its air filter system ensures that the engine runs smoothly by keeping dirt and debris at bay, which can be particularly useful in dusty conditions.

Overall, the Troy-Bilt TB4000 stands out in the realm of tillers, providing exceptional performance, durability, and user comfort. Whether you are new to gardening or a seasoned pro, this tiller is designed to meet the demands of various gardening tasks, making it an excellent investment for anyone dedicated to cultivating lush and healthy landscapes.
Top Page Image Contents