Trane UH-SVX01A-EN manual Options P Models, Vertical Louver Cone Diffuser optional

Page 31

Options

Options: P Models

Variable Speed Control 115 Volt Only (optional)

The solid state speed controller may be installed at any convenient location and is suitable for surface or flush type mounting. A standard electrical single or double gang wall box is recommended as in Figure 30.

Figure 30. Wiring Diagram of Speed Control Installation

Installation Procedure:

1.Attach the control's leads to the electrical leads in the control box using wire nuts. The speed control is to be wired in series with the motor. See wiring diagram in Figure 30.

2.Make certain wire nuts are tight with no copper wire being exposed.

3.Place wires and wire nuts back into box allowing room for the control to fit in box also.

4.Mount speed control to box using number 6 flathead screws provided.

Setting the Control:

1.Turn the control shaft fully clockwise. If the motor is not running at the desired low speed, adjust the trim on the face of the control for low speed setting using a small screwdriver.

2.Rotate the control shaft counter clockwise. The speed will increase smoothly from minimum to maximum and then switch off.

Vertical Louver Cone Diffuser (optional)

Rubber mounts and mounting nuts and bolts are provided with each louver cone diffuser. Attach the

diffuser to the bottom of the unit heater as shown in Figure 51. Mounting holes are provided in the unit base plate.

Adjust the diffuser to provide the desired air pattern.

Strap-On Water Control

A SPDT strap-on type hot water control with 100° to 240°F (38 to 116°C) rated at 10 amps at 120V is also available. Control can be used for direct or reverse acting applications as high or low limit.

Steam Pressure Control

SPDT switch opens on a rise in pressure. Control is automatically reset, has a range of 0 to 15 PSIG (0 to 103 kPa) and has an adjustable differential. Other actions, ranges, circuits and manual reset models are available on request.

Thermostats

Line voltage wall thermostats are in stock for immediate shipment. All models are SPST with bimetal thermometer, knob-type set point adjustment, 40 to 90°F (5 to 30°C) range and selector switches. Standard duty models with "off-auto" and a heavy duty model with "auto- offfan" switching are available. Other models available on request. Plastic tamperproof one size fits all thermostat guards are also available.

Wall Mounted Speed Controllers

Motors up to and including 1/8 HP (115V) can be operated at reduced speeds by addition of optional speed controller. Controller is 5 amps, pre- set at factory for maximum and minimum speeds, with intermediate

Figure 31. Louver Cone Diffuser Attached to Vertical Unit Heater

speeds indefinitely controllable. All 1/ 3, 1/2 HP and 230V motors operate only at rated speed and CFM - See Charts.

Manual Starters

Single and three-phase models are available. Standard models are single-speed, toggle-operated, NEMA Type 1 and are surface- mounted.

CAUTION:

When using electrical accessories, always refer to the accessory manufacturer's installation manual for proper use, location and wiring instructions.

UH-SVX01A-EN

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Unit Heaters Hazard Identification Preface and Warnings and CautionsContents Model Number Description Service Model Number DescriptionDescription Digit 8-VOLTAGE Model Number Description300 360 LocationModel Maximum Mounting HT Approx. Max Throw ft mFour Point Suspension-Shelf Mounted Motors Only LocationForced HOT Water Forced HOT Water High Pressure Steam LOW Pressure Steam Gravity LOW Pressure Vapor or Vacuum Structural Integrity InstallationPeriodic Service Heavy Objects Lifting/Suspension Methods= Low Speed = Low output model with all air ports open InstallationUnit Size Steam Pressure PSI 17.5Spread ft m Maximum SpreadSteam Pressure PSI Unit Size Model NoFt m Diffuser Cone See a See B Standard Low Output ModelPressure Temperature SteamTemperature WaterPiping Installation Unit Mounting Heavy Objects Installation S TypeLouver Cone Diffuser Fan Guard/Louver InstallationVertical Unit with Osha Fan Guard Vertical Unit with Louver Cone DiffuserUnit Capacity MBH Fan Dia Min Dimensional DataDimensional Data P Model ModelsMBH Dimensional DataModels Roughing in Dimensional Data Model Size Unit Capacity FanDIAM. inches Ship WT. lbs Dimensional Data S ModelInches NO. NOM. FANHeader Type Models 18 thru NOM FAN Approx Diam Ship Header ModelsApproximate factors at varying altitudes Technical DataTechnical Data S Models Corrections When Using Glycol Solution in SystemTechnical Data P Model Technical DataCategory of Area Sound Rating Options S Models OptionsOptions P Models OptionsVertical Louver Cone Diffuser optional Operation Thermostat Wiring and LocationElectrical Connections Electrical Connections P Model Hazardous VoltageFan Motor Connections Low Voltage CCW Internal Marathon Electrical ConnectionsSpeed Controller with Manual Starting Switch Wiring Installation P ModelElectrical Connections S Model Hazardous Voltage Manual Control with Three Phase MotorWiring Installation S Model Electrical Connections AMP MCA MOP RPM Motor DataMotor Data P Models Voltage Selections Standard Totally Enclosed Motor Type MT=11145 Motor DataExplosion Proof with Thermal Overload Motor Type MT=2 Unit ModelExplosion Proof with Thermal Overload Motor Type Totally Enclosed Motor TypeBTU Steam Performance DataModel S Header Type Only OutputSteam Calculations and Correction Factors Steam Performance DataKg/hr Sq. m Properties of Saturated SteamModel P Standard Units Steam Pressure in Psig kPa037 Low Output Standard Vertical Units with All Air Ports Open13.8 34.5 68.9 103.4 137.9 206.8 275.8 344.7 517.1 Steam Calculations and Correction Factors P StyleSteam Correction Factors Based on 2 LBS. Steam 60 E.A.T Entering Steam Pressure LBS. PER SQ. IN. Saturated AIR TempCFM FPM Hot Water Performance DataModel S Serpentine and Header Type BTU/HRWater Flow Hot Water Performance DataHot Water Calculations and Correction Factors S Type IV. Capacity AT Other RatesTemperat Entering Entering Water Temperature F C AIRMinimum Water Flow Heating Capacity Factors for Various Rates of Water FlowCFM Type Standard Output Units117.6 24.24 108.8 34.5 529 318 42.7 138.0 041 720152.2 376 11,000 2250 237 1165 133 11.430 470.9 32.35Hot Water Performance Data IV. Pressure Loss AT Other TDs HOT Water Calculations and Correction Factor P StyleCapacity @ 20 TD II. Capacity AT Other TDs10 6 15 8 20 Minimum Water Flow GPMRotating Components MaintenancePeriodic Service Hazardous Voltage Cleaning the UnitAdditional P Model Instructions MaintenanceFan and Motor Assembly Troubleshooting GuideLimited Warranty S Model Warranty InfoLimited Warranty P Model Warranty Info Page Trane

UH-SVX01A-EN specifications

The Trane UH-SVX01A-EN is an advanced unit ventilator designed to provide efficient and reliable heating, cooling, and ventilation in various commercial and educational applications. This unit is particularly engineered for use in schools, offices, and healthcare facilities, ensuring optimal indoor air quality while maintaining energy efficiency.

One of the main features of the UH-SVX01A-EN is its innovative design that incorporates cutting-edge technologies for enhanced performance. The unit is equipped with a high-efficiency fan and motor system that operates quietly while delivering consistent airflow. This ensures a comfortable environment for occupants without the disruptive noise common in traditional ventilation systems.

Another standout characteristic of the UH-SVX01A-EN is its versatility. It offers multiple configuration options, allowing it to be tailored to meet specific building requirements and occupant needs. The unit can be integrated with various control systems, including advanced building management systems, which provide precise temperature control and enhance energy savings.

The use of variable air volume technology allows the UH-SVX01A-EN to adjust airflow rates based on real-time occupancy and environmental conditions. This intelligent airflow management not only improves comfort but also significantly reduces energy consumption, aligning with sustainable building practices.

Additionally, Trane has incorporated a range of filtration options within the unit, which contribute to improved indoor air quality by capturing dust, allergens, and other airborne particulates. This makes the UH-SVX01A-EN an ideal choice for settings where air purity is paramount, such as healthcare environments.

Maintenance of the UH-SVX01A-EN is also user-friendly, with easy access to key components for servicing and inspections. Trane's commitment to reliability and efficiency is manifested in the durable materials and construction of this unit, ensuring longevity and lower lifetime operational costs.

In summary, the Trane UH-SVX01A-EN combines advanced technology, versatile configurations, and a focus on energy efficiency and indoor air quality. This unit ventilator is designed to meet the demands of modern buildings while supporting environmental sustainability initiatives. With its robust features and flexible integration options, the UH-SVX01A-EN stands out as a reliable solution for any commercial heating, cooling, and ventilation needs.
Top Page Image Contents