Trane UH-SVX01A-EN manual Model Number Description, Digit 8-VOLTAGE

Page 5

Model Number Description

180180,000 BTU/HR

204204,000 BTU/HR

240240,000 BTU/HR

280280,000 BTU/HR

300300,000 BTU/HR

360360,000 BTU/HR

DIGIT 8—VOLTAGE

1 115/1/60

3230/1/60 (115 V motor with Transformer)

4208/3/60

5230/3/60

6460/3/60

7575/60/3 (Totally Enclosed) (P only)

DIGIT 17 - Manual Starter

0

None

A

Manual Starter

DIGIT 18 - STEAM & HOT WATER CONTROL

0None

1Strap on Hot Water Control

2Steam Pressure Control (Open on rise in pressure)

3Steam Pressure Control (Close on rise in pressure)

45.0 Amp Speed Control Switch ( Capacities 18 - 108 only)

DIGIT 9 - MOTOR TYPE

TTotally Enclosed

E Explosion Proof

DIGIT 10- DESIGN SEQUENCE

A

DIGIT 11- TUBE MATERIAL

ACopper

BSteel (P only)

DIGIT 12- FAN GUARD

1OSHA Fan Guard

2Standard Fan Guard (3 phase or Explosion Proof motors only)

3Standard Fan Guard (Unit Capacities 240 - 360)

DIGIT 13 - SPECIAL COATING

0 No Special Coating

APhenolic Coating (Baked)

BEpoxy

CEpoxy Phenolic

DIGIT 14 - DISCONNECT SWITCH

0None

1Disconnect switch

DIGIT 15 - THERMOSTATS (LINE VOLTAGE)

0 None

ALight Duty TSTAT w/ subbase Line Volts 8 Amps

BHeavy Duty TSTAT w/ subbase&guard Line Volts 16 Amps+A32

DIGIT 19 - VERTICAL LOUVER

0 None

AVertical Louver

BFin Diffuser (P only)

CFin Diffuser w/ Coating (Ponly)

DIGIT 16 - THERMOSTAT COVER

0

None

 

A

Locking Thermostat Cover

 

UH-SVX01A-EN

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Unit Heaters Hazard Identification Preface and Warnings and CautionsContents Description Service Model Number DescriptionModel Number Description Digit 8-VOLTAGE Model Number DescriptionModel Maximum Mounting HT Approx. Max LocationThrow ft m 300 360Four Point Suspension-Shelf Mounted Motors Only LocationForced HOT Water Forced HOT Water High Pressure Steam LOW Pressure Steam Gravity LOW Pressure Vapor or Vacuum Periodic Service Heavy Objects InstallationLifting/Suspension Methods Structural IntegrityUnit Size Steam Pressure PSI Installation17.5 = Low Speed = Low output model with all air ports openSteam Pressure PSI Unit Size Maximum SpreadModel No Spread ft mFt m Diffuser Cone See a See B Standard Low Output ModelTemperature Temperature SteamWater PressurePiping Installation Unit Mounting Heavy Objects Installation S TypeLouver Cone Diffuser Fan Guard/Louver InstallationVertical Unit with Osha Fan Guard Vertical Unit with Louver Cone DiffuserDimensional Data P Model Dimensional DataModels Unit Capacity MBH Fan Dia MinModels Roughing in Dimensional Data Model Size Dimensional DataUnit Capacity Fan MBHInches Dimensional Data S ModelNO. NOM. FAN DIAM. inches Ship WT. lbsHeader Type Models 18 thru NOM FAN Approx Diam Ship Header ModelsTechnical Data S Models Technical DataCorrections When Using Glycol Solution in System Approximate factors at varying altitudesCategory of Area Sound Rating Technical DataTechnical Data P Model Options S Models OptionsVertical Louver Cone Diffuser optional OptionsOptions P Models Electrical Connections Thermostat Wiring and LocationElectrical Connections P Model Hazardous Voltage OperationFan Motor Connections Low Voltage CCW Internal Marathon Electrical ConnectionsSpeed Controller with Manual Starting Switch Wiring Installation P ModelElectrical Connections S Model Hazardous Voltage Manual Control with Three Phase MotorWiring Installation S Model Electrical Connections Motor Data P Models Voltage Selections Motor DataStandard Totally Enclosed Motor Type MT=1 AMP MCA MOP RPMExplosion Proof with Thermal Overload Motor Type MT=2 Motor DataUnit Model 1145Explosion Proof with Thermal Overload Motor Type Totally Enclosed Motor TypeModel S Header Type Only Steam Performance DataOutput BTUSteam Calculations and Correction Factors Steam Performance DataModel P Standard Units Properties of Saturated SteamSteam Pressure in Psig kPa Kg/hr Sq. m037 Low Output Standard Vertical Units with All Air Ports OpenSteam Correction Factors Based on 2 LBS. Steam 60 E.A.T Steam Calculations and Correction Factors P StyleEntering Steam Pressure LBS. PER SQ. IN. Saturated AIR Temp 13.8 34.5 68.9 103.4 137.9 206.8 275.8 344.7 517.1Model S Serpentine and Header Type Hot Water Performance DataBTU/HR CFM FPMHot Water Calculations and Correction Factors S Type Hot Water Performance DataIV. Capacity AT Other Rates Water FlowMinimum Water Flow Entering Entering Water Temperature F C AIRHeating Capacity Factors for Various Rates of Water Flow TemperatCFM Type Standard Output Units117.6 24.24 108.8 34.5 529 318 42.7 152.2 376 72011,000 2250 237 1165 133 11.430 470.9 32.35 138.0 041Hot Water Performance Data Capacity @ 20 TD HOT Water Calculations and Correction Factor P StyleII. Capacity AT Other TDs IV. Pressure Loss AT Other TDs10 6 15 8 20 Minimum Water Flow GPMPeriodic Service Hazardous Voltage MaintenanceCleaning the Unit Rotating ComponentsFan and Motor Assembly MaintenanceTroubleshooting Guide Additional P Model InstructionsLimited Warranty P Model Warranty InfoLimited Warranty S Model Warranty Info Page Trane

UH-SVX01A-EN specifications

The Trane UH-SVX01A-EN is an advanced unit ventilator designed to provide efficient and reliable heating, cooling, and ventilation in various commercial and educational applications. This unit is particularly engineered for use in schools, offices, and healthcare facilities, ensuring optimal indoor air quality while maintaining energy efficiency.

One of the main features of the UH-SVX01A-EN is its innovative design that incorporates cutting-edge technologies for enhanced performance. The unit is equipped with a high-efficiency fan and motor system that operates quietly while delivering consistent airflow. This ensures a comfortable environment for occupants without the disruptive noise common in traditional ventilation systems.

Another standout characteristic of the UH-SVX01A-EN is its versatility. It offers multiple configuration options, allowing it to be tailored to meet specific building requirements and occupant needs. The unit can be integrated with various control systems, including advanced building management systems, which provide precise temperature control and enhance energy savings.

The use of variable air volume technology allows the UH-SVX01A-EN to adjust airflow rates based on real-time occupancy and environmental conditions. This intelligent airflow management not only improves comfort but also significantly reduces energy consumption, aligning with sustainable building practices.

Additionally, Trane has incorporated a range of filtration options within the unit, which contribute to improved indoor air quality by capturing dust, allergens, and other airborne particulates. This makes the UH-SVX01A-EN an ideal choice for settings where air purity is paramount, such as healthcare environments.

Maintenance of the UH-SVX01A-EN is also user-friendly, with easy access to key components for servicing and inspections. Trane's commitment to reliability and efficiency is manifested in the durable materials and construction of this unit, ensuring longevity and lower lifetime operational costs.

In summary, the Trane UH-SVX01A-EN combines advanced technology, versatile configurations, and a focus on energy efficiency and indoor air quality. This unit ventilator is designed to meet the demands of modern buildings while supporting environmental sustainability initiatives. With its robust features and flexible integration options, the UH-SVX01A-EN stands out as a reliable solution for any commercial heating, cooling, and ventilation needs.
Top Page Image Contents