Tiger Products Co., Ltd RBF-12C manual Getting on and OFF the Tractor, Tractor Ballast

Page 56
(SBM-11)

OPERATION

2.4 Tractor Ballast

To ensure tractor stability when operating on flat surfaces the left rear tractor tire MUST exert a minimum down force (weight) of 1500 lbs. on the ground when the tractor is on level ground, its boom is fully extended and the mower head is horizontal and two feet above the ground. For units which have the ability to operate on either side of the tractor, these requirements must also be met for the right side tire when the boom is extended to the left side as described above. A tractor that does not meet this criteria is DANGEROUS and should not be operated as upset of the unit can occur resulting in possible serious injury and property damage. NOTE: All factory mounted units are tested and meet the ballast requirement before shipment; further testing is not required unless the unit is operated in a manner other than what is considered standard operating conditions.

For additional information on properly ballasting the tractor, refer to Alamo Industrial Tractor and Mower Stability Pamphlet P/N #02959010.

DANGER! Each Rear Wheel must have a minimum of 1500 pound contact with the surface to prevent lateral instability and possible tip-over which could result in serious bodily injury or even death. Widen the wheel tread and add weights if needed. Refer to the mounting instructions or call Customer Service if you need assistance with Counterweight Procedure.

If the unit is operated on slopes greater than 5°, additional counterweight will be required. Operation of the unit on slopes greater than 11° is not recommended under any circumstances. On a tractor with a 96” outside to outside tire spread, a 11° slope occurs when one rear tractor tire is about 8” lower than the other rear tire.

WARNING! Do not operate the unit under any circumstance if the slope is 10° or greater.

3. GETTING ON AND OFF THE TRACTOR

The operator must read and completely understand this manual and the tractor operator’s manual before starting any boom mower operation. If any part of either manual is not completely understood, consult an authorized dealer for a complete explanation. If the operator of the equipment can not read the manuals for themselves, it is the supervisors responsibility to read and explain the manuals and operating instructions to them.

RBF-12C 07/04

Operation Section 4-6

© 2004 Alamo Group Inc.

 

Image 56
Contents RBF-12C To the OWNER/OPERATOR/DEALER Table of Contents Page Safety Section Safety Peligro ¡LEA EL InstructivoAgent. SG-22 Wait a minute...Save a life Not match the Tractor PTO Equipment Operation Safety Instructions and Practices Stop Mowing if Passersby are Within 100 Yards UN- LessSBM-10 Stop Mowing if Passersby are Within 100 Yards Unless Dismounting.SG-39 SGM-7 SGM-11 Maintenance and Service Safety Instructions and Practices Or death. SBM-12 Parts Information See Your Tiger DealerTransporting Safety Instructions and Practices Regulations. SG-6 Storage and Parking Safety Instructions and Practices 14 11 10 25 20 QTY Level Description Safety Safety Safety Safety Safety Safety Safety Safety This Act Seeks DutiesOsha Regulations Employer ResponsibilitiesIntroduction Section Introduction Before Operating this MachineAssembly Section Machine Preparation GeneralTractor Requirements Fitting Machine to Tractor Assembly Fitting PTO SectionFitting Controls Lever UnitFill Tank with OIL Adjust Lever Pivot PositionHydraulic Systems RBF-12C Assembly Section Fitting Rotor Unit Connecting the Motor Mechanical BreakoutHose Layout TwistsSharp Bends Chafing HosesFlexible Front Guard KIT Accumulator KITRBF 12C Assembly Section Bleeding the First Ram Initial RUNBleeding Rams Assembly Page Operation Section Connectingattaching Heads Operation Tiger Rear Mount Boom Operation InstructionsOperation Tractor Requirements and Capabilities Operator RequirementsTractor Requirements Shatter Proof Safety Windows Rops and Seat BeltOperator Thrown Object Protection Tractor Lighting and SMV EmblemGetting on and OFF the Tractor Tractor BallastBoarding the Tractor Dismounting the TractorStarting the Tractor Connecting Attaching Head to the Boom Dash Nominal Torque Value Size IN.LBS FT.LBSPRE-OPERATION Inspection and Service Tractor Pre-Operation Inspection/ServiceBoom ARM Assembly Boom Unit Pre-Operation Inspection and ServiceFrame Assembly Hydraulic Line Inspection Hydraulic PUMP/OIL ReservoirFlail Head Inspection Operating the Control Valves Valve Operation Plate P/N Driving the Tractor and Mower Brake and Differential Lock Setting Starting the TractorDriving the Tractor and Mower Operating the Boom Unit and Attached Head Foreign Debris Hazards / Overhead Obstructions Operating Speed and Ground Speed Operating the Attached Mower HeadsGround Level and Scrub Cutting lower roller to its maximum Grass FlailRoller Height Operation Alternative Rotor Link Positions Grass CuttingHedge Trimming Stalling the RotorMotor Position TRACTOR, BOOM, and Attached Head Storage Shutting Down the Attached HeadTransporting the Tractor and Mower Transporting on Public Roadways Hauling the Tractor and Mower Trouble Shooting Guide Page Maintenance Section Lubrication GearboxGrease Points PTO Drive TubesFilter Replacement Power TAKE-OFF ShaftHoses and Rotor Drive Circuit Hydraulic OilsRotor Unit Hydraulic CylindersStorage Parking and RemovalClose Isolator Valves on First ARM and Accumulator if Fitted Proper Torque for Fasteners Figure Warranty Information ONE Last Word RBF-12C-OMWPL-07/04 Printed U.S.A

RBF-12C specifications

Tiger Products Co., Ltd has consistently been at the forefront of innovation in the manufacturing industry, and their latest offering, the RBF-12C, exemplifies this commitment to excellence. The RBF-12C is a precision-built, high-performance industrial robot designed to enhance productivity and efficiency in various manufacturing processes.

One of the standout features of the RBF-12C is its impressive load capacity. With the ability to handle payloads of up to 12 kilograms, this model is perfect for applications requiring both strength and precision. This robustness makes it suitable for a range of tasks, including assembly, welding, and material handling.

In terms of technologies, the RBF-12C is equipped with advanced motion control systems. Its high-speed servo motors enable swift and accurate movements, minimizing cycle times while maximizing productivity. The robot's ability to achieve precise positioning is enhanced by its built-in feedback systems, which continuously monitor and adjust the robot's movements for optimal performance.

Another significant characteristic of the RBF-12C is its user-friendly interface. The robot comes with an intuitive programming environment that allows users to easily create and modify programs without needing extensive coding knowledge. This accessibility reduces the learning curve for new users and enables companies to integrate the RBF-12C into their existing workflows with minimal disruptions.

Safety is also a top priority with the RBF-12C. The robot is designed with multiple safety features, including collision detection and emergency stop functionalities, ensuring that operations are conducted smoothly without compromising worker safety. This makes the RBF-12C an ideal choice for environments where human-robot collaboration is essential.

Furthermore, the RBF-12C boasts a compact design, which allows for flexible deployment in confined spaces often found in modern manufacturing facilities. Its modular structure also means that it can be easily customized to meet specific operational requirements, accommodating various tools and attachments depending on the task at hand.

In conclusion, Tiger Products Co., Ltd’s RBF-12C robot stands out for its robust payload capacity, advanced motion control technologies, user-friendly programming interface, safety features, and compact design. These characteristics make it an invaluable asset for any manufacturing process looking to enhance efficiency and productivity while maintaining high standards of safety and adaptability.