Tiger Products Co., Ltd RBF-12C manual Connecting Attaching Head to the Boom

Page 59
(SG-15)

OPERATION

5. CONNECTING ATTACHING HEAD TO THE BOOM

The rotor unit can now be fitted to the end of the arms. The illustration shows the Rhino 1948 cowl bracket. Start the tractor engine and raise the second arm so that the mower head clamp is approximately 300mm (18 in.) clear of the ground. Place the mower head directly in front of the second arm. Level up mower head with wood packing. Remove clamp bracket (A) from the end of arms. Adjust position of the arms until the mower head clamp is lined up with the clamping bar on top of the rotor unit in the desired position along the bar. Replace clamp bracket (A) and nut and washers (B). Tighten fully. Note: Additional support may be needed at the end of the Boom to aid in installation.

5.2 Connecting Mower Head Hydraulics

Attach the 1" hoses, from the articulating arm to the hydraulic motor on the head. Use recommended hose end torque values in chart below.

DASH

NOMINAL

TORQUE

VALUE*

SIZE

SIZE (IN.)

(IN.LBS.)

(FT.LBS.)

-4

1/4

140

12

-6

3/8

230

19

-8

1/2

450

38

-10

5/8

650

54

-12

3/4

900

75

-16

1

1200

100

-20

1-1/4

1600

133

-24

1-1/2

2000

167

-32

2

2800

233

* Straight threads do not always seal better when higher torques are used. Too much torque causes distortion and may lead to leakage.

Boom

End

Return

Head

Pressure

DANGER! Do not operate this Equipment with hydraulic oil leaking. Oil is expensive and leaking oil could present a hazard. Do not check for leaks with your hand! Use a piece of heavy paper or cardboard. High- pressure oil streams from breaks in the line could penetrate the skin and cause tissue damage including gangrene. If oil does penetrate the skin, have the injury treated immediately by a physician.

RBF-12C 07/04

Operation Section 4-9

© 2004 Alamo Group Inc.

 

Page 58 Page 60
Image 59
Page 58 Page 60
Contents RBF-12C To the OWNER/OPERATOR/DEALER Table of Contents Page Safety Section Safety ¡LEA EL Instructivo PeligroAgent. SG-22 Wait a minute...Save a life Not match the Tractor PTO Stop Mowing if Passersby are Within 100 Yards UN- Less Equipment Operation Safety Instructions and PracticesSBM-10 Stop Mowing if Passersby are Within 100 Yards Unless Dismounting.SG-39 SGM-7 SGM-11 Maintenance and Service Safety Instructions and Practices Or death. SBM-12 See Your Tiger Dealer Parts InformationTransporting Safety Instructions and Practices Regulations. SG-6 Storage and Parking Safety Instructions and Practices 14 11 10 25 20 QTY Level Description Safety Safety Safety Safety Safety Safety Safety Safety Employer Responsibilities This Act SeeksDuties Osha RegulationsIntroduction Section Before Operating this Machine IntroductionAssembly Section Machine Preparation GeneralTractor Requirements Fitting Machine to Tractor Assembly Section Fitting PTOLever Unit Fitting ControlsFill Tank with OIL Adjust Lever Pivot PositionHydraulic Systems RBF-12C Assembly Section Fitting Rotor Unit Twists Connecting the MotorMechanical Breakout Hose LayoutChafing Hoses Sharp BendsAccumulator KIT Flexible Front Guard KITRBF 12C Assembly Section Bleeding the First Ram Initial RUNBleeding Rams Assembly Page Operation Section Operation Tiger Rear Mount Boom Operation Instructions Connectingattaching HeadsOperation Tractor Requirements and Capabilities Operator RequirementsTractor Requirements Tractor Lighting and SMV Emblem Shatter Proof Safety WindowsRops and Seat Belt Operator Thrown Object ProtectionTractor Ballast Getting on and OFF the TractorDismounting the Tractor Boarding the TractorStarting the Tractor Dash Nominal Torque Value Size IN.LBS FT.LBS Connecting Attaching Head to the BoomTractor Pre-Operation Inspection/Service PRE-OPERATION Inspection and ServiceBoom ARM Assembly Boom Unit Pre-Operation Inspection and ServiceFrame Assembly Hydraulic PUMP/OIL Reservoir Hydraulic Line InspectionFlail Head Inspection Operating the Control Valves Valve Operation Plate P/N Driving the Tractor and Mower Starting the Tractor Brake and Differential Lock SettingDriving the Tractor and Mower Operating the Boom Unit and Attached Head Foreign Debris Hazards / Overhead Obstructions Operating the Attached Mower Heads Operating Speed and Ground SpeedGround Level and Scrub Cutting lower roller to its maximum Grass FlailRoller Height Operation Grass Cutting Alternative Rotor Link PositionsStalling the Rotor Hedge TrimmingMotor Position Shutting Down the Attached Head TRACTOR, BOOM, and Attached Head StorageTransporting the Tractor and Mower Transporting on Public Roadways Hauling the Tractor and Mower Trouble Shooting Guide Page Maintenance Section PTO Drive Tubes LubricationGearbox Grease PointsHydraulic Oils Filter ReplacementPower TAKE-OFF Shaft Hoses and Rotor Drive CircuitParking and Removal Rotor UnitHydraulic Cylinders StorageClose Isolator Valves on First ARM and Accumulator if Fitted Proper Torque for Fasteners Figure Warranty Information ONE Last Word RBF-12C-OMWPL-07/04 Printed U.S.A

RBF-12C specifications

Tiger Products Co., Ltd has consistently been at the forefront of innovation in the manufacturing industry, and their latest offering, the RBF-12C, exemplifies this commitment to excellence. The RBF-12C is a precision-built, high-performance industrial robot designed to enhance productivity and efficiency in various manufacturing processes.

One of the standout features of the RBF-12C is its impressive load capacity. With the ability to handle payloads of up to 12 kilograms, this model is perfect for applications requiring both strength and precision. This robustness makes it suitable for a range of tasks, including assembly, welding, and material handling.

In terms of technologies, the RBF-12C is equipped with advanced motion control systems. Its high-speed servo motors enable swift and accurate movements, minimizing cycle times while maximizing productivity. The robot's ability to achieve precise positioning is enhanced by its built-in feedback systems, which continuously monitor and adjust the robot's movements for optimal performance.

Another significant characteristic of the RBF-12C is its user-friendly interface. The robot comes with an intuitive programming environment that allows users to easily create and modify programs without needing extensive coding knowledge. This accessibility reduces the learning curve for new users and enables companies to integrate the RBF-12C into their existing workflows with minimal disruptions.

Safety is also a top priority with the RBF-12C. The robot is designed with multiple safety features, including collision detection and emergency stop functionalities, ensuring that operations are conducted smoothly without compromising worker safety. This makes the RBF-12C an ideal choice for environments where human-robot collaboration is essential.

Furthermore, the RBF-12C boasts a compact design, which allows for flexible deployment in confined spaces often found in modern manufacturing facilities. Its modular structure also means that it can be easily customized to meet specific operational requirements, accommodating various tools and attachments depending on the task at hand.

In conclusion, Tiger Products Co., Ltd’s RBF-12C robot stands out for its robust payload capacity, advanced motion control technologies, user-friendly programming interface, safety features, and compact design. These characteristics make it an invaluable asset for any manufacturing process looking to enhance efficiency and productivity while maintaining high standards of safety and adaptability.
Top Page Image Contents