Tiger Products Co., Ltd RBF-12C manual Dismounting.SG-39

Page 14
(SG-40)
(SG-29)
(SG-26)
(SG-15)
(SG-13)

SAFETY

DANGER! Start tractor only when properly seated in the Tractor seat. Starting a tractor in gear can result in injury or death. Read the Tractor operators manual for proper starting instructions.

DANGER! Do not operate this Equipment with hydraulic oil leaking. Oil is expensive and its presence could present a hazard. Do not check for leaks with your hand! Use a piece of heavy paper or cardboard. High- pressure oil streams from breaks in the line could penetrate the skin and cause tissue damage including gangrene. If oil does penetrate the skin, have the injury treated immediately by a physician knowledge- able and skilled in this procedure.

DANGER! Never run the tractor engine in a closed building or without adequate ventilation. The exhaust fumes can be hazardous to your health.

(SG-23)

WARNING! Do not exceed the rated PTO speed for the Implement. Excessive PTO speeds can cause Implement driveline or blade failures resulting in serious injury or death.

DANGER! Operate the Tractor and/or Implement controls only while properly seated in the Tractor seat with the seat belt securely fastened around you. Inadvertent movement of the Tractor or Implement may cause serious injury or death.

WARNING! In case of mechincal difficulty during operation, place the transmission in the park position, set the parking brake, shut down all power, including the PTO and the engine and remove the key. Wait until all rotating motion has stop before

dismounting.(SG-39)

WARNING! Do Not operate this equipment in areas where insects such as bees may attack you and/or cause you to lose control of the equipment. If you must enter in such areas, use a tractor with an enclosed Cab and close the windows to prevent insects from entering. If a tractor cab is not available, wear suitable clothing including head, face, and hand protection to shield you from the insects. Attacking insects can cause you to lose control of the tractor, which can result in serious injury or death to you or bystanders. Never dismount a moving tractor.

RBF-12C 07-04

Safety Section 1-10

© 2004 Alamo Group Inc.

 

Page 13 Page 15
Image 14
Page 13 Page 15
Contents RBF-12C To the OWNER/OPERATOR/DEALER Table of Contents Page Safety Section Safety Peligro ¡LEA EL InstructivoAgent. SG-22 Wait a minute...Save a life Not match the Tractor PTO Equipment Operation Safety Instructions and Practices Stop Mowing if Passersby are Within 100 Yards UN- LessSBM-10 Stop Mowing if Passersby are Within 100 Yards Unless Dismounting.SG-39 SGM-7 SGM-11 Maintenance and Service Safety Instructions and Practices Or death. SBM-12 Parts Information See Your Tiger DealerTransporting Safety Instructions and Practices Regulations. SG-6 Storage and Parking Safety Instructions and Practices 14 11 10 25 20 QTY Level Description Safety Safety Safety Safety Safety Safety Safety Safety Osha Regulations This Act SeeksDuties Employer ResponsibilitiesIntroduction Section Introduction Before Operating this MachineAssembly Section Machine Preparation GeneralTractor Requirements Fitting Machine to Tractor Assembly Fitting PTO SectionFitting Controls Lever UnitFill Tank with OIL Adjust Lever Pivot PositionHydraulic Systems RBF-12C Assembly Section Fitting Rotor Unit Hose Layout Connecting the MotorMechanical Breakout TwistsSharp Bends Chafing HosesFlexible Front Guard KIT Accumulator KITRBF 12C Assembly Section Bleeding the First Ram Initial RUNBleeding Rams Assembly Page Operation Section Connectingattaching Heads Operation Tiger Rear Mount Boom Operation InstructionsOperation Tractor Requirements and Capabilities Operator RequirementsTractor Requirements Operator Thrown Object Protection Shatter Proof Safety WindowsRops and Seat Belt Tractor Lighting and SMV EmblemGetting on and OFF the Tractor Tractor BallastBoarding the Tractor Dismounting the TractorStarting the Tractor Connecting Attaching Head to the Boom Dash Nominal Torque Value Size IN.LBS FT.LBSPRE-OPERATION Inspection and Service Tractor Pre-Operation Inspection/ServiceBoom ARM Assembly Boom Unit Pre-Operation Inspection and ServiceFrame Assembly Hydraulic Line Inspection Hydraulic PUMP/OIL ReservoirFlail Head Inspection Operating the Control Valves Valve Operation Plate P/N Driving the Tractor and Mower Brake and Differential Lock Setting Starting the TractorDriving the Tractor and Mower Operating the Boom Unit and Attached Head Foreign Debris Hazards / Overhead Obstructions Operating Speed and Ground Speed Operating the Attached Mower HeadsGround Level and Scrub Cutting lower roller to its maximum Grass FlailRoller Height Operation Alternative Rotor Link Positions Grass CuttingHedge Trimming Stalling the RotorMotor Position TRACTOR, BOOM, and Attached Head Storage Shutting Down the Attached HeadTransporting the Tractor and Mower Transporting on Public Roadways Hauling the Tractor and Mower Trouble Shooting Guide Page Maintenance Section Grease Points LubricationGearbox PTO Drive TubesHoses and Rotor Drive Circuit Filter ReplacementPower TAKE-OFF Shaft Hydraulic OilsStorage Rotor UnitHydraulic Cylinders Parking and RemovalClose Isolator Valves on First ARM and Accumulator if Fitted Proper Torque for Fasteners Figure Warranty Information ONE Last Word RBF-12C-OMWPL-07/04 Printed U.S.A

RBF-12C specifications

Tiger Products Co., Ltd has consistently been at the forefront of innovation in the manufacturing industry, and their latest offering, the RBF-12C, exemplifies this commitment to excellence. The RBF-12C is a precision-built, high-performance industrial robot designed to enhance productivity and efficiency in various manufacturing processes.

One of the standout features of the RBF-12C is its impressive load capacity. With the ability to handle payloads of up to 12 kilograms, this model is perfect for applications requiring both strength and precision. This robustness makes it suitable for a range of tasks, including assembly, welding, and material handling.

In terms of technologies, the RBF-12C is equipped with advanced motion control systems. Its high-speed servo motors enable swift and accurate movements, minimizing cycle times while maximizing productivity. The robot's ability to achieve precise positioning is enhanced by its built-in feedback systems, which continuously monitor and adjust the robot's movements for optimal performance.

Another significant characteristic of the RBF-12C is its user-friendly interface. The robot comes with an intuitive programming environment that allows users to easily create and modify programs without needing extensive coding knowledge. This accessibility reduces the learning curve for new users and enables companies to integrate the RBF-12C into their existing workflows with minimal disruptions.

Safety is also a top priority with the RBF-12C. The robot is designed with multiple safety features, including collision detection and emergency stop functionalities, ensuring that operations are conducted smoothly without compromising worker safety. This makes the RBF-12C an ideal choice for environments where human-robot collaboration is essential.

Furthermore, the RBF-12C boasts a compact design, which allows for flexible deployment in confined spaces often found in modern manufacturing facilities. Its modular structure also means that it can be easily customized to meet specific operational requirements, accommodating various tools and attachments depending on the task at hand.

In conclusion, Tiger Products Co., Ltd’s RBF-12C robot stands out for its robust payload capacity, advanced motion control technologies, user-friendly programming interface, safety features, and compact design. These characteristics make it an invaluable asset for any manufacturing process looking to enhance efficiency and productivity while maintaining high standards of safety and adaptability.
Top Page Image Contents