Tiger Products Co., Ltd RBF-12C manual General, Tractor Requirements, Machine Preparation

Page 36

ASSEMBLY

GENERAL

The Rhino 1348, 1548, and 1948 differ slightly in some areas. Notes have been provided for these differ- ences, be sure to refer to the proper note for your machine.

TRACTOR REQUIREMENTS

Before preparing the tractor for the machine make sure that specifications of the tractor meet the re- quirements listed below.

A.6 spline P.T.O. of 1-3/8" dia.

B.A P.T.O. output of 540 rev/min.

C.A top link is available.

D.As a guide for suitable tractor size the ballasted weight of tractor should exceed 2750 kg (6050 lbs)

E.Adequate ballast should be added to the rear wheel opposite to the arms and front of the tractor to ensure stability. The amount will vary depending on type of tractor used and prevailing conditions.

MACHINE PREPARATION

The machine will normally be delivered with the arms fully assembled to the mainframe, but with the mower head detached.

The lifting points FIGURE 3-1 (A), 3-1 (B) and FIGURE 3-2 (A) are for machines without the mower head attached or hydraulic oil. When lifting machine in anything other than this conditions extreme care should be exercised as the center of gravity may change. Only personnel experienced in lift and hoist operation should attempt it. Note the Lifting Point and transport straps / retaining chain differ between the 1348/ 1548 and the 1948 (see FIGURE 3-1).

A.Position the machine on a flat hard surface.

B.If not already fitted, lift the machine and fit the parking stands which will be found stored under the mainframe.

C.Remove the transport straps 3-1 (C), 3-1 (D), identified by the red panel.

Remove the retaining chain and greasing setscrew from transport plate and fit into tapped hole of first/

second arm pin and tighten up.

NOTE: The second arm on the RBF-12 is required to be moved from on top the first arm to below the first arm and the second ram re-fitted to it.

FIGURE 3-1

RBF-12C 07-04

Assembly Section 3-2

© 2004 Alamo Group Inc.

 

Page 35 Page 37
Image 36
Page 35 Page 37
Contents RBF-12C To the OWNER/OPERATOR/DEALER Table of Contents Page Safety Section Safety Peligro ¡LEA EL InstructivoAgent. SG-22 Wait a minute...Save a life Not match the Tractor PTO Equipment Operation Safety Instructions and Practices Stop Mowing if Passersby are Within 100 Yards UN- LessSBM-10 Stop Mowing if Passersby are Within 100 Yards Unless Dismounting.SG-39 SGM-7 SGM-11 Maintenance and Service Safety Instructions and Practices Or death. SBM-12 Parts Information See Your Tiger DealerTransporting Safety Instructions and Practices Regulations. SG-6 Storage and Parking Safety Instructions and Practices 14 11 10 25 20 QTY Level Description Safety Safety Safety Safety Safety Safety Safety Safety This Act Seeks DutiesOsha Regulations Employer ResponsibilitiesIntroduction Section Introduction Before Operating this MachineAssembly Section General Tractor RequirementsMachine Preparation Fitting Machine to Tractor Assembly Fitting PTO SectionFitting Controls Lever UnitAdjust Lever Pivot Position Hydraulic SystemsFill Tank with OIL RBF-12C Assembly Section Fitting Rotor Unit Connecting the Motor Mechanical BreakoutHose Layout TwistsSharp Bends Chafing HosesFlexible Front Guard KIT Accumulator KITRBF 12C Assembly Section Initial RUN Bleeding RamsBleeding the First Ram Assembly Page Operation Section Connectingattaching Heads Operation Tiger Rear Mount Boom Operation InstructionsOperation Operator Requirements Tractor RequirementsTractor Requirements and Capabilities Shatter Proof Safety Windows Rops and Seat BeltOperator Thrown Object Protection Tractor Lighting and SMV EmblemGetting on and OFF the Tractor Tractor BallastBoarding the Tractor Dismounting the TractorStarting the Tractor Connecting Attaching Head to the Boom Dash Nominal Torque Value Size IN.LBS FT.LBSPRE-OPERATION Inspection and Service Tractor Pre-Operation Inspection/ServiceBoom Unit Pre-Operation Inspection and Service Frame AssemblyBoom ARM Assembly Hydraulic Line Inspection Hydraulic PUMP/OIL ReservoirFlail Head Inspection Operating the Control Valves Valve Operation Plate P/N Driving the Tractor and Mower Brake and Differential Lock Setting Starting the TractorDriving the Tractor and Mower Operating the Boom Unit and Attached Head Foreign Debris Hazards / Overhead Obstructions Operating Speed and Ground Speed Operating the Attached Mower HeadsGrass Flail Roller HeightGround Level and Scrub Cutting lower roller to its maximum Operation Alternative Rotor Link Positions Grass CuttingHedge Trimming Stalling the RotorMotor Position TRACTOR, BOOM, and Attached Head Storage Shutting Down the Attached HeadTransporting the Tractor and Mower Transporting on Public Roadways Hauling the Tractor and Mower Trouble Shooting Guide Page Maintenance Section Lubrication GearboxGrease Points PTO Drive TubesFilter Replacement Power TAKE-OFF ShaftHoses and Rotor Drive Circuit Hydraulic OilsRotor Unit Hydraulic CylindersStorage Parking and RemovalClose Isolator Valves on First ARM and Accumulator if Fitted Proper Torque for Fasteners Figure Warranty Information ONE Last Word RBF-12C-OMWPL-07/04 Printed U.S.A

RBF-12C specifications

Tiger Products Co., Ltd has consistently been at the forefront of innovation in the manufacturing industry, and their latest offering, the RBF-12C, exemplifies this commitment to excellence. The RBF-12C is a precision-built, high-performance industrial robot designed to enhance productivity and efficiency in various manufacturing processes.

One of the standout features of the RBF-12C is its impressive load capacity. With the ability to handle payloads of up to 12 kilograms, this model is perfect for applications requiring both strength and precision. This robustness makes it suitable for a range of tasks, including assembly, welding, and material handling.

In terms of technologies, the RBF-12C is equipped with advanced motion control systems. Its high-speed servo motors enable swift and accurate movements, minimizing cycle times while maximizing productivity. The robot's ability to achieve precise positioning is enhanced by its built-in feedback systems, which continuously monitor and adjust the robot's movements for optimal performance.

Another significant characteristic of the RBF-12C is its user-friendly interface. The robot comes with an intuitive programming environment that allows users to easily create and modify programs without needing extensive coding knowledge. This accessibility reduces the learning curve for new users and enables companies to integrate the RBF-12C into their existing workflows with minimal disruptions.

Safety is also a top priority with the RBF-12C. The robot is designed with multiple safety features, including collision detection and emergency stop functionalities, ensuring that operations are conducted smoothly without compromising worker safety. This makes the RBF-12C an ideal choice for environments where human-robot collaboration is essential.

Furthermore, the RBF-12C boasts a compact design, which allows for flexible deployment in confined spaces often found in modern manufacturing facilities. Its modular structure also means that it can be easily customized to meet specific operational requirements, accommodating various tools and attachments depending on the task at hand.

In conclusion, Tiger Products Co., Ltd’s RBF-12C robot stands out for its robust payload capacity, advanced motion control technologies, user-friendly programming interface, safety features, and compact design. These characteristics make it an invaluable asset for any manufacturing process looking to enhance efficiency and productivity while maintaining high standards of safety and adaptability.
Top Page Image Contents