Tiger Products Co., Ltd RBF-12C Boom Unit Pre-Operation Inspection and Service, Frame Assembly

Page 61

OPERATION

6.2 Boom Unit Pre-Operation Inspection and Service

Inspect and service the boom arm and head prior to operation. Damaged and/or broken parts should be repaired and/or replaced immediately. To ensure the unit is ready for operation, conduct the following:

¾Ensure that the Manual Canister is secured to the Boom unit with the Operator’s Manual inside.

¾Ensure all decals are in place and legible. Replace missing, worn, and non-legible decals.

NOTE: The mower Operator’s Manual and affixed Decals contain important instructions on the safe and proper use of the mower. Maintain these important safety features on the mower in good condition to ensure the information is available to the operator at all times.

FRAME ASSEMBLY

¾Inspect condition of mounting frame weldment.

¾Inspect condition of King Post frame.

¾Ensure all bolts and screws are in position and are properly torqued.

¾Ensure all pins are in place and fastened with screws.

¾Ensure frame is properly mounted to tractor and hardware is properly installed and tightened.

BOOM ARM ASSEMBLY

¾Inspect condition of each arm section weldment

¾Ensure all pins are in place.

¾Ensure all bolts and screws are properly installed.

¾Check condition of teflon bushings at boom pivot points.

¾Ensure each hydraulic cylinder is installed and retained correctly. Ensure the proper size pins are used to retain the cylinders in place and are secured properly.

¾Ensure that all joints are lubricated. See Maintenance Section for Lubrication Chart.

Frame

Weldment

WARNING!

Never attempt to lubricate, adjust, or remove material from the Implement while it is in motion

 

or while tractor engine is running. Make sure the tractor engine is off before working on the

 

Implement. (SG-20)

 

RBF-12C 07/04

Operation Section 4-11

© 2004 Alamo Group Inc.

 

Page 60 Page 62
Image 61
Page 60 Page 62
Contents RBF-12C To the OWNER/OPERATOR/DEALER Table of Contents Page Safety Section Safety ¡LEA EL Instructivo PeligroAgent. SG-22 Wait a minute...Save a life Not match the Tractor PTO Stop Mowing if Passersby are Within 100 Yards UN- Less Equipment Operation Safety Instructions and PracticesSBM-10 Stop Mowing if Passersby are Within 100 Yards Unless Dismounting.SG-39 SGM-7 SGM-11 Maintenance and Service Safety Instructions and Practices Or death. SBM-12 See Your Tiger Dealer Parts InformationTransporting Safety Instructions and Practices Regulations. SG-6 Storage and Parking Safety Instructions and Practices 14 11 10 25 20 QTY Level Description Safety Safety Safety Safety Safety Safety Safety Safety Duties This Act SeeksOsha Regulations Employer ResponsibilitiesIntroduction Section Before Operating this Machine IntroductionAssembly Section Tractor Requirements GeneralMachine Preparation Fitting Machine to Tractor Assembly Section Fitting PTOLever Unit Fitting ControlsHydraulic Systems Adjust Lever Pivot PositionFill Tank with OIL RBF-12C Assembly Section Fitting Rotor Unit Mechanical Breakout Connecting the MotorHose Layout TwistsChafing Hoses Sharp BendsAccumulator KIT Flexible Front Guard KITRBF 12C Assembly Section Bleeding Rams Initial RUNBleeding the First Ram Assembly Page Operation Section Operation Tiger Rear Mount Boom Operation Instructions Connectingattaching HeadsOperation Tractor Requirements Operator RequirementsTractor Requirements and Capabilities Rops and Seat Belt Shatter Proof Safety WindowsOperator Thrown Object Protection Tractor Lighting and SMV EmblemTractor Ballast Getting on and OFF the TractorDismounting the Tractor Boarding the TractorStarting the Tractor Dash Nominal Torque Value Size IN.LBS FT.LBS Connecting Attaching Head to the BoomTractor Pre-Operation Inspection/Service PRE-OPERATION Inspection and ServiceFrame Assembly Boom Unit Pre-Operation Inspection and ServiceBoom ARM Assembly Hydraulic PUMP/OIL Reservoir Hydraulic Line InspectionFlail Head Inspection Operating the Control Valves Valve Operation Plate P/N Driving the Tractor and Mower Starting the Tractor Brake and Differential Lock SettingDriving the Tractor and Mower Operating the Boom Unit and Attached Head Foreign Debris Hazards / Overhead Obstructions Operating the Attached Mower Heads Operating Speed and Ground SpeedRoller Height Grass FlailGround Level and Scrub Cutting lower roller to its maximum Operation Grass Cutting Alternative Rotor Link PositionsStalling the Rotor Hedge TrimmingMotor Position Shutting Down the Attached Head TRACTOR, BOOM, and Attached Head StorageTransporting the Tractor and Mower Transporting on Public Roadways Hauling the Tractor and Mower Trouble Shooting Guide Page Maintenance Section Gearbox LubricationGrease Points PTO Drive TubesPower TAKE-OFF Shaft Filter ReplacementHoses and Rotor Drive Circuit Hydraulic OilsHydraulic Cylinders Rotor UnitStorage Parking and RemovalClose Isolator Valves on First ARM and Accumulator if Fitted Proper Torque for Fasteners Figure Warranty Information ONE Last Word RBF-12C-OMWPL-07/04 Printed U.S.A

RBF-12C specifications

Tiger Products Co., Ltd has consistently been at the forefront of innovation in the manufacturing industry, and their latest offering, the RBF-12C, exemplifies this commitment to excellence. The RBF-12C is a precision-built, high-performance industrial robot designed to enhance productivity and efficiency in various manufacturing processes.

One of the standout features of the RBF-12C is its impressive load capacity. With the ability to handle payloads of up to 12 kilograms, this model is perfect for applications requiring both strength and precision. This robustness makes it suitable for a range of tasks, including assembly, welding, and material handling.

In terms of technologies, the RBF-12C is equipped with advanced motion control systems. Its high-speed servo motors enable swift and accurate movements, minimizing cycle times while maximizing productivity. The robot's ability to achieve precise positioning is enhanced by its built-in feedback systems, which continuously monitor and adjust the robot's movements for optimal performance.

Another significant characteristic of the RBF-12C is its user-friendly interface. The robot comes with an intuitive programming environment that allows users to easily create and modify programs without needing extensive coding knowledge. This accessibility reduces the learning curve for new users and enables companies to integrate the RBF-12C into their existing workflows with minimal disruptions.

Safety is also a top priority with the RBF-12C. The robot is designed with multiple safety features, including collision detection and emergency stop functionalities, ensuring that operations are conducted smoothly without compromising worker safety. This makes the RBF-12C an ideal choice for environments where human-robot collaboration is essential.

Furthermore, the RBF-12C boasts a compact design, which allows for flexible deployment in confined spaces often found in modern manufacturing facilities. Its modular structure also means that it can be easily customized to meet specific operational requirements, accommodating various tools and attachments depending on the task at hand.

In conclusion, Tiger Products Co., Ltd’s RBF-12C robot stands out for its robust payload capacity, advanced motion control technologies, user-friendly programming interface, safety features, and compact design. These characteristics make it an invaluable asset for any manufacturing process looking to enhance efficiency and productivity while maintaining high standards of safety and adaptability.
Top Page Image Contents