Teledyne T265 manual Getting Started, Unpacking, Could Damage Instrument And Void Warranty

Page 15

3. GETTING STARTED

3. GETTING STARTED

This section addresses the procedures for unpacking the instrument and inspecting for damage, and introduces the instrument layout, then presents the procedures for getting started: making electrical and pneumatic connections, and conducting an initial calibration check. Please see the Model T200 Operation Manual for more information.

3.1 UNPACKING

CAUTION – GENERAL SAFETY HAZARD

To avoid personal injury, always use two persons to lift and carry the Model T265.

ATTENTION

COULD DAMAGE INSTRUMENT AND VOID WARRANTY

Printed Circuit Assemblies (PCAs) are sensitive to electro-static discharges too small to be felt by the human nervous system. Failure to use ESD protection when working with electronic assemblies will void the instrument warranty

See A Primer on Electro-Static Discharge in the accompanying Model T200 manual for more information on preventing ESD damage.

CAUTION - ELECTRICAL SHOCK HAZARD

Never disconnect PCAs, wiring harnesses or electronic subassemblies while

analyzer is under power.

07337B DCN6324

13

Image 15

Contents Model T265 Chemiluminescence Ozone Analyzer Manual AddendumTELEDYNE ADVANCED POLLUTION INSTRUMENTATION 9480 CARROLL PARK DRIVE SAN DIEGO, CA USAPage Phone IMPORTANT SAFETY INFORMATIONCustomer Service Department Email: api-customerservice@teledyne.comCONSIGNES DE SÉCURITÉ Description of Changes ABOUT THIS MANUALREVISION HISTORY 2011 December 07, Model T265 AddendumThis page intentionally left blank TABLE OF CONTENTS 07337B DCN6324 1.1 OVERVIEW 1. INTRODUCTIONIntroduction 2.SPECIFICATIONS, APPROVALS, & CERTIFICATIONS Table 2-1.Model T265 Specifications 2.2APPROVALS AND CERTIFICATIONS 2.3 WARRANTY2.2.1 Safety 2.1 EPA DESIGNATIONSpecifications, Approvals, & Certifications COULD DAMAGE INSTRUMENT AND VOID WARRANTY 3. GETTING STARTED3.1 UNPACKING Lift the cover straight up 3.2 INSTRUMENT LAYOUT 3.2.1 Front PanelFigure 3-1.Front Panel Figure 3-2.Rear Panel 3.2.2 Rear PanelFigure 3-3.Internal Chassis Layout 3.2.3 Internal Chassis Layout3.3.1Electrical and Pneumatic Connections 3.3 CONNECTIONS AND SETUPFigure 3-4.T265 Pneumatics, Basic Configuration 3.4.1 Startup 3.4.2Initial Calibrationcomponents to heat to operating temperature Step ActionComment Step 4. MAINTENANCE 4.1 MAINTENANCE SCHEDULE4.2MAINTENANCE ITEMS SPECIFIC TO THE MODEL T265 Maintenance 5. PRINCIPLES OF OPERATION NO  O3  NO2*  O2NO2*  NO2  hv Principles of Operation APPENDIX A Models T265 and 265E Menu Trees 07337B DCN6324 Press to cycle through the active warning 1Only appears when warning messages are active· · · · · · · · · · · · · · · · · APPENDIX A-1 Software Menu Trees Sample Menu07337B DCN6324 APPENDIX B - Spare Parts 07337B DCN6324 T265 Spare Parts List PARTNUMBERDESCRIPTION DESCRIPTION T265 Spare Parts ListReference 07388 06/01/2011 PARTNUMBERDESCRIPTION T265 Spare Parts ListReference 07388 06/01/2011, 15 PARTNUMBER07337B DCN6324 EMAIL api-customerservice@teledyne.com Appendix C Warranty/Repair QuestionnaireM265E and T265 Values are in the Signal I/OAppendix C Warranty/Repair Questionnaire M265E and T265APPENDIX D - Wire List and Electronic Schematics 07337B DCN6324 T265 INTERCONNECT LIST 07337B DCN6324 T265 INTERCONNECT LIST07337B DCN6324 T265 INTERCONNECT LIST07337B DCN6324 T265 INTERCONNECT LIST07337B DCN6324