Teledyne T265 manual Connections And Setup, 3.3.1Electrical and Pneumatic Connections

Page 20
3.3 CONNECTIONS AND SETUP

Getting Started

Model T265 Chemiluminescence Ozone Analyzer Addendum to Model T200 Manual

 

 

3.3 CONNECTIONS AND SETUP

This section presents connection information for setting up the instrument to operate.

3.3.1Electrical and Pneumatic Connections

1.Refer to Figure 3-2for the rear panel electrical and pneumatic connectors.

2.Mount the NOx scrubber with base down (arrow labeled “FLOW” pointing down) onto the rear panel.

3.Connect tubing from NOx scrubber base fitting to rear panel fitting labeled “FROM SCRUBBER”.

4.Connect tubing from NOx scrubber top fitting to rear panel fitting labeled “TO SCRUBBER”.

5.Vent the EXHAUST port to atmospheric pressure and out of the room, because of its nitric oxide content.

CAUTION

GENERAL SAFETY HAZARD

Analyzer Exhaust Contains Nitric Oxide Gas.

Vent pump exhaust to a well-ventilated area at atmospheric pressure. Obtain a Material Safety Data Sheet (MSDS) for this material. Read and rigorously follow the safety guidelines described there.

6.Attach the sample inlet line to the sample inlet port. The pressure of the sample gas at the inlet port should be at ambient pressure and constant.

7.Using 1/8” stainless steel tubing, attach a cylinder with 10,000 ppm ±10% of nitric oxide (NO) in nitrogen (N2), with an appropriate pressure regulator, to the 1/8” stainless steel port (labeled NITRIC OXIDE) on the rear panel as shown in Figure 3-2.Note: The NO cylinder’s pressure regulator should be set to deliver gas at 20 PSIG ± 5 PSIG.

8.Attach a strip chart recorder and/or data-logger to the appropriate analog output connections on the rear panel. See section on analog output connections in the Model T200 manual for connector pin-out definitions.

9.Connect the power cord to the correct line voltage.

WARNING

Lethal voltages present inside the analyzer’s case.

 Do not operate with cover off during normal operation.

Before operation, check for correct input voltage and frequency.

 Do not operate without proper chassis grounding.

Do not defeat the ground wire on power plug.

Turn off analyzer power before disconnecting electrical subassemblies.

18

07337B DCN6324

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Manual Addendum TELEDYNE ADVANCED POLLUTION INSTRUMENTATION9480 CARROLL PARK DRIVE SAN DIEGO, CA USA Model T265 Chemiluminescence Ozone AnalyzerPage IMPORTANT SAFETY INFORMATION Customer Service DepartmentEmail: api-customerservice@teledyne.com PhoneCONSIGNES DE SÉCURITÉ ABOUT THIS MANUAL REVISION HISTORY2011 December 07, Model T265 Addendum Description of ChangesThis page intentionally left blank TABLE OF CONTENTS This page intentionally left blank 1. INTRODUCTION 1.1 OVERVIEWIntroduction 2.SPECIFICATIONS, APPROVALS, & CERTIFICATIONS Table 2-1.Model T265 Specifications 2.3 WARRANTY 2.2.1 Safety2.1 EPA DESIGNATION 2.2APPROVALS AND CERTIFICATIONS07337B DCN6324 3.1 UNPACKING COULD DAMAGE INSTRUMENT AND VOID WARRANTY3. GETTING STARTED Lift the cover straight up Figure 3-1.Front Panel 3.2 INSTRUMENT LAYOUT3.2.1 Front Panel 3.2.2 Rear Panel Figure 3-2.Rear Panel3.2.3 Internal Chassis Layout Figure 3-3.Internal Chassis Layout3.3 CONNECTIONS AND SETUP 3.3.1Electrical and Pneumatic ConnectionsFigure 3-4.T265 Pneumatics, Basic Configuration components to heat to operating temperature 3.4.1 Startup3.4.2Initial Calibration Comment StepAction Step 4.2MAINTENANCE ITEMS SPECIFIC TO THE MODEL T265 4. MAINTENANCE4.1 MAINTENANCE SCHEDULE Maintenance NO2*  NO2  hv 5. PRINCIPLES OF OPERATIONNO  O3  NO2*  O2 Principles of Operation APPENDIX A Models T265 and 265E Menu Trees This page intentionally left blank 1Only appears when warning messages are active · · · · · · · · · · · · · · · · ·APPENDIX A-1 Software Menu Trees Sample Menu Press to cycle through the active warning07337B DCN6324 APPENDIX B - Spare Parts This page intentionally left blank DESCRIPTION T265 Spare Parts ListPARTNUMBER T265 Spare Parts List Reference 07388 06/01/2011PARTNUMBER DESCRIPTIONT265 Spare Parts List Reference 07388 06/01/2011, 15PARTNUMBER DESCRIPTIONThis page intentionally left blank Appendix C Warranty/Repair Questionnaire M265E and T265Values are in the Signal I/O EMAIL api-customerservice@teledyne.comWarranty/Repair Questionnaire M265E and T265 Appendix CAPPENDIX D - Wire List and Electronic Schematics This page intentionally left blank T265 INTERCONNECT LIST T265 INTERCONNECT LIST 07337B DCN6324T265 INTERCONNECT LIST 07337B DCN6324T265 INTERCONNECT LIST 07337B DCN632407337B DCN6324
Top Page Image Contents