White Outdoor 500 Before Stopping, To Stop The Snow Thrower, To Engage Drive, To Engage Augers

Page 11

against the starter.

3.If the engine still fails to start, repeat the first two steps. If continued attempts do not free starter, follow the electric starter procedures to start.

4.Avoid freezing of the recoil starter by referring to instructions below.

Before Stopping

1.Run engine for a few minutes to help dry off any moisture on engine.

2.Avoid freezing of the starter by following these steps before stopping the snow thrower:

Recoil Starter

a.With the engine running, pull the starter rope with a rapid, continuous full arm stroke three or four times.

Electric Starter

a.Connect power cord to switch box, then to 120 Volt AC receptacle.

b.While the engine is running, push the starter button and spin the starter for several seconds.

c.Disconnect power cord from the receptacle first, then from the snow thrower.

NOTE: The unusual sound from pulling the starter rope in case of the recoil starter, or from spinning the starter in case of the electric starter, will not harm the engine.

To Stop The Snow Thrower

1.To stop the wheels, release the traction drive lever on the snow thrower.

2.To stop throwing snow, release auger drive lever.

3.To stop engine, push throttle control lever to OFF and pull out the key. Do not turn key.

To Engage Drive

1.With the engine running near top speed, move shift lever to one of six FORWARD positions or two REVERSE positions. Select a speed appropriate for the snow conditions that exist. Use slower speeds until you are familiar with the process.

2.Squeeze traction drive clutch grip against the right handle and the snow thrower will move. Release it and the drive motion will stop.

To Engage Augers

1.To engage augers and start snow throwing, squeeze the left hand auger clutch grip against the left handle. Release to stop augers.

2.While the auger control is engaged, squeeze the drive control to move, release to stop. Do not shift speeds while the drive is engaged.

NOTE: This same lever also locks auger control so you can turn the chute crank without interrupting the snow throwing process.

3.Release the auger control; the interlock mechanism should keep the auger control engaged until the traction drive control is released.

4.Release the drive control to stop both the augers and the wheel drive. To stop the auger, both levers must be released.

To Throw Snow

CAUTION: Check the area to be cleared for foreign objects. Remove, if any.

1.Start the engine following starting instructions.

2.Rotate the discharge chute to the desired position, (away from bystanders and/or buildings) by moving the chute control.

3.Select the speed according to snow condition.

CAUTION: Never move the shift lever without first releasing the drive clutch.

4.Engage the auger control and drive control levers following instructions above.

5.The interlock feature will allow you to remove your left hand from the auger control lever.

6.When clearing the first pass through the snow, control speed of snow thrower according to the depth and condition of snow.

7.To turn the unit left or right, squeeze the respective wheel steering control. See Figure 12.

8.On each succeeding pass, readjust the chute to the desired position and slightly overlap previous path.

9.After the area is cleared, stop the snow thrower following instructions given below.

Operating Tips

NOTE: Allow the engine to warm up for a few minutes as the engine will not develop full power until it reaches operating temperature.

WARNING: The temperature of muffler and

surrounding areas may exceed (150o F (65o C). Avoid these areas.

•For most efficient snow removal, remove snow immediately after it falls.

•Discharge snow downwind whenever possible. Slightly overlap each previous swath.

•Set the skid shoes 1/4" below the scraper bar for normal usage. The skid shoes may be adjusted upward for hard-packed snow.

NOTE: It is not recommended that you operate this snow thrower on gravel as loose gravel can be easily picked up and thrown by the auger causing an injury or damage to the snow thrower.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Operator’s Manual Table of Contents Training Important Safe Operation PracticesYour Responsibility Maintenance And StorageUnpacking Setting UP Your Snow ThrowerBefore Assembly Setting up the Snow ThrowerFor Models with 4 Way Chute Control Box Final AdjustmentsLamp Wire optional Chute Clean-Out ToolSkid Shoe Auger Control TestDrive Control & Shift Lever Drive Control/ Auger Control Lock Operating Your Snow ThrowerKnow The Controls Tire Pressure Pneumatic TiresStarting The Engine Stopping Snow ThrowerBefore Starting Gas & Oil Fill-Up Warm Start Electric StarterRecoil Starter Cold StartTo Engage Augers Before StoppingTo Stop The Snow Thrower To Engage DriveEngine Chute Clean-Out ToolMaintaining Your Snow Thrower General RecommendationsCheck Chute Cables Service & AdjustmentCheck V-Belts Check Friction WheelAuger Belt Replacing BeltShave Plate and Skid Shoes Replacing Skid ShoeDrive Belt Friction Wheel RubberShift Rod AdjustmentsDrive Clutch Auger ClutchChute Control OFF-SEASON StorageTroubleshooting Tractor Attachment Warranty Three 3 Year Limited Warranty
Related manuals
Manual 16 pages 26.46 Kb

500 specifications

The White Outdoor 500 is a rugged and versatile lawn and garden tractor designed for homeowners looking to tackle a variety of outdoor tasks with ease. Renowned for its robust construction and reliable performance, the White Outdoor 500 is equipped with a host of features that make it a valuable addition to any landscape maintenance arsenal.

One of the standout features of the White Outdoor 500 is its powerful engine, typically powered by a dependable Briggs & Stratton or Kohler engine. This engine provides ample horsepower to handle a wide range of conditions, from mowing grassy lawns to tackling tougher terrain and heavy gardening tasks. The engine is designed for easy starting and efficient fuel consumption, ensuring that homeowners can complete their tasks without frequent interruptions for refueling.

The tractor is equipped with a hydrostatic transmission, offering seamless acceleration and smooth operation. This user-friendly system allows operators to easily control speed and direction without the need for shifting gears, enabling a more comfortable mowing experience. The tractor's design promotes maneuverability, making it suitable for navigating around obstacles like trees and flower beds.

Another key characteristic of the White Outdoor 500 is its cutting deck. The tractor typically features a wide, multi-blade cutting system that ensures a clean and even cut across various grass types and lengths. Many models include adjustable cutting heights, allowing users to customize their lawn care according to seasonal requirements or personal preferences. The robust construction of the deck ensures durability, even under the rigors of regular use.

The White Outdoor 500 also prioritizes comfort and ease of use. With an ergonomic seat design, users can enjoy extended mowing sessions without experiencing fatigue. The placement of controls is intuitive, making it easy to operate various functions like headlights, deck engagement, and throttle adjustments.

In addition, the tractor often features advanced technologies such as a built-in mulching system and bagging capabilities that allow homeowners to collect clippings for easy disposal or recycling. As a result, maintaining a tidy lawn becomes a simple affair.

Overall, the White Outdoor 500 is a reliable and efficient lawn tractor that combines power, comfort, and advanced features for a superior mowing experience, making it a popular choice among homeowners looking for a dependable solution to their outdoor maintenance needs.
Top Page Image Contents