Woods Equipment RBC60 LRC60 Assembly Instructions, Dealer SET-UP Instructions, Assemble Blade

Page 15

ASSEMBLY INSTRUCTIONS

DEALER SET-UP INSTRUCTIONS

Assembly of this Rear Blade/Landscape Rake is the responsibility of the WOODS dealer. It should be deliv- ered to the owner completely assembled, lubricated and adjusted for normal cutting conditions.

The Rear Blade/Landscape Rake is shipped partially assembled. Assembly will be easier if components are aligned and loosely assembled before tightening hard- ware. Recommended torque values for hardware are located on page 24.

„Before dismounting power unit or performing any service or maintenance, follow these steps: disengage power to equipment, lower the 3-point hitch and all raised components to the ground, operate valve levers to release any hydraulic pres- sure, set parking brake, stop engine, remove key, and unfasten seat belt.

„NEVER GO UNDERNEATH EQUIPMENT. Never place any part of the body underneath equipment or between moveable parts even when the engine has been turned off. Hydraulic system leak-down, hydraulic system failures, mechanical failures, or movement of control levers can cause equipment to drop or rotate unexpectedly and cause severe injury or death.

•Service work does not require going under- neath.

•Read Operator's Manual for service instruc- tions or have service performed by a qualified dealer.

„Keep all persons away from operator control area while performing adjustments, service, or maintenance.

CAUTION

„Always wear relatively tight and belted clothing to avoid entanglement in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate.

Assemble Blade

Attach Pivot Assembly to Moldboard

1.Remove two plow bolts (28) from center moldboard

(5) and cutting edge.

2.Remove two carriage bolts (26) from top of moldboard.

3.Align holes on pivot assembly (6) with holes on moldboard.

4.Secure pivot assembly to moldboard using hardware previously remove. Use plow bolts (28), hardened flat washer (25), and hex nut (24) in the bottom two holes and carriage bolts (26), hardened flat washer (25), and hex nut (24) in the top two holes.

 

24

 

25

24

 

25

 

6

CD6156-2

 

 

26

5

 

 

28

5.

Moldboard

6.

Pivot assembly

24.

5/8 NC Hex nut

25.

5/8 Hardened flat washer

26.

5/8 NC x 1-1/2 Carriage bolt GR5

28.

5/8 NC x 2 Plow bolt

Figure 12. Pivot Assembly to Moldboard

Attach Rear Blade Frame to Pivot Assembly

1.Remove pivot cap (3) and hardware from pivot assembly (6).

2.Support moldboard in an upright position.

3.Place rear blade frame assembly (9) over pivot tube on pivot assembly (6).

MAN0169 (Rev. 5/6/2005)

Assembly 15

 

 

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Rear Blade & Landscape Rake To the Dealer IntroductionLEA EL Instructivo Table of ContentsSpecifications General InformationRBC60 LRC60 Preparation SafetySafety Rules TrainingStorage MaintenanceSafety & Instructional Decals Be Careful Replace Immediately If DamagedOperation OperationConnect Rear Blade or Rake to Tractor Reversing Blade or Rake Offsetting Blade OnlyCategory 0 / 1 Hitch Pin Kit Optional Operating TechniquesParking Stand Placement BackfillingCutting Ditches Blade Only Owner’s Responsibility PRE-OPERATION Check ListReplacing Blade Cutting Edge MaintenanceMaintenance LRC60 Tine ReplacementPeriodically or Before Extended Storage Tail Wheel Adjustment LRC60 OptionalCleaning After Each UseAssemble Blade AssemblyAssembly Instructions Dealer SET-UP InstructionsInstall Optional Caster Wheels Landscape Rake Assembly Landscape RakeQuick Hitch Bushing Kit Optional Install Optional Skid Shoe Kit Rear BladeManual Storage Tube Kit Manual Storage Tube Kit OptionalDelivery Check List Dealer Check ListsDealer Check Lists PRE-DELIVERY Check ListParts RBC60/LRC60 AssemblyManual Storage Tube KIT Optional PartsCategory 1 Quick Hitch Bushing KIT Optional RBC60 Skid Shoe & LRC60 Tail Wheel OptionalCategory 0 / 1 Hitch PIN KIT Optional Appendix Bolt Torque ChartSAE Series Torque Chart Metric Series Torque ChartAbbreviations Bolt Size ChartWarranty Rev /23/2005 MAN0169

RBC60 LRC60 specifications

Woods Equipment Company is renowned for its commitment to high-quality agricultural and landscaping machinery. One of their standout products is the RBC60 LRC60 landscape rake, specifically designed for commercial users and serious landscapers looking for reliability and efficiency in their projects.

The Woods RBC60 LRC60 features a robust design, emphasizing durability without sacrificing performance. Its construction incorporates heavy-duty materials, ensuring prolonged use even in demanding conditions. This model has been engineered to withstand the rigors of regular use on various terrains, making it an ideal choice for both commercial and residential landscaping tasks.

One of the main features of the RBC60 LRC60 is its adjustable rake angle. Users can quickly adapt the rake's position to suit different applications, from leveling soil to spreading gravel or mulch efficiently. This adjustability allows operators to achieve optimal results, tailoring their approach to the specific requirements of each job.

Additionally, the RBC60 LRC60 comes equipped with a unique set of tines. These tines are designed for versatility, allowing for effective soil preparation, debris collection, and fine grading. The design ensures that elements like rocks and other unwanted materials are efficiently disturbed, making it easier for landscapers to achieve a smooth, even surface.

The hydraulic lift system provides ease of operation, allowing users to raise and lower the rake effortlessly while maintaining control. This feature helps maximize productivity, as operators can quickly transition between tasks without needing to leave their machinery.

Another essential characteristic of the Woods RBC60 LRC60 is its compatibility with a wide range of tractors. This versatility allows it to be used in various applications, from landscaping and gardening to preparing fields. The attachment system is designed for quick disconnect, making it user-friendly for those who operate multiple tools in their work.

In summary, the Woods Equipment RBC60 LRC60 landscape rake combines durability, versatility, and efficiency. Its adjustable rake angle, specialized tines, and hydraulic lift system provide landscapers with the tools they need to tackle a variety of projects effectively. As such, the RBC60 LRC60 represents a valuable addition to the arsenal of any serious professional in the landscaping and agricultural sector, ensuring outstanding performance and reliability on every job.
Top Page Image Contents