Woods Equipment FSW6000T, FSW6000F manual WAY Angle Mount KIT, Holes in Sweepster Shield

Page 12

 

 

 

 

 

20

 

 

8--1/4

 

 

 

 

 

 

5

10

 

TRIM INPUT SHAFT

 

 

 

 

 

 

 

 

 

 

 

24

8

DRILL .343 (11/32) DIA

 

 

 

 

21

 

 

 

9

HOLES IN SWEEPSTER SHIELD

 

 

 

 

 

 

 

7

 

 

 

 

 

 

 

 

 

 

23

 

 

 

 

22

 

6

 

 

 

 

 

 

 

 

 

 

24

 

 

 

 

2

4

 

 

 

 

 

 

 

 

 

22

 

 

 

 

CD4647A

 

 

 

11

 

 

1

3

 

 

 

 

 

1.

Broom mount

7.

2-1/2" Clamp

 

21. 5/16" NC Flanged hex lock nut

2.

12V Actuator

8.

Extension spring

 

22. 1/2 NC x 2-1/2 Hex head cap screw

3.

Universal half sheet

9.

Upper actuator mount

23. 1/2 NC x 3 Hex head cap screw

4.

Universal half sleeve

10. Caster wheel assembly right

24. 1/2 NC Hex locknut

5.

Power shaft shield

11. Caster wheel assembly left

 

6.

Shield mount strap

20. 5/16" x 3/4" NC Hex head cap screw

 

Figure 3. 2-Way Angle Sweeper Installation

2-WAY ANGLE MOUNT KIT

(Figure 3)

Attach upper actuator mount (9) to square upright mast on Sweeper broom head using 1/2 x 3 bolt and 1/2 locknut.

Mark Sweeper input driveshaft at 8-1/4 inches from the center cross. Loosen the set screw retaining the rect- angular shaft and remove it from the U-joint. Cut shaft to proper length and reinstall shaft and secure with set screws.

Position broom head in front of mount while inserting broom head input shaft into sleeve assembly (4). Bolt broom head to mount (1) using bolts provided with broom head.

Attach fixed end of upper actuator (2) to mount using 1/2 x 2-1/2 bolt and 1/2 locknut. Attach rod end of actu- ator to slots in upper actuator mount (9) using 1/2 x 2- 1/2 bolts and 1/2 locknut. Slide broom head left or right

until actuator lines up with upper mount. Do not over tighten, rod must be able to float in slot. Attach wire from actuator motor to black and white wires from the switch box.

Attach extension spring (8) to hole in broom head mast and to hole in main mount near rear actuator mounting location.

Attach 2-1/2 clamp (7) and shield mount strap (6) to round cross member of broom frame. Do not tighten fully so shield may be adjusted. Attach power shaft shield (5) to strap. Position shield so it can be bolted to existing chain shield of broom head. Drill 2.343 (11/32) dia holes in broom head shield to mount power shaft shield. Bolt power shaft shield to broom head and tighten all bolts and clamps.

Attach broom and mount to tractor according to instruc- tion in the following section.

10 Assembly

MAN0118 (Rev. 12/23/2004)

 

Image 12
Contents MOW’N Machine Sweeper Ii Introduction To the DealerTable of Contents IntroductionSafety Safety RulesTraining PreparationMaintenance TransportationStorage Safety & Instructional Decals Be Careful33347E Operation OperationUneven Terrain PRE-OPERATION Check ListOwner Responsibility Service ServiceChain Adjustment LubricationAssembly AssemblyFixed Angle Mount KIT Installation Dealer SET-UP InstructionsWAY Angle Mount KIT Holes in Sweepster ShieldWAY Angle Wiring Instructions Attaching Sweeper to TractorIgnition Purple Dealer Check List Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListWAY Angle Sweeper Assembly PartsREF Part Description Fixed Angle Sweeper Mount KIT Assembly Part QTY DescriptionWAY Angle Sweeper Wire Diagram Bolt Torque Chart SAE Series Torque ChartTypical Washer Installations AppendixBolt Size Chart AbbreviationsLimited Warranty What is Covered MAN0118 Woods Equipment Company

FSW6000F, FSW6000T specifications

Woods Equipment is a renowned manufacturer of high-quality agricultural and landscaping equipment, and the FSW6000F and FSW6000T are prime examples of their commitment to durable, efficient, and innovative design. These flail mowers are engineered to cater to the needs of both professionals and enthusiasts in the agricultural and landscaping sectors.

The FSW6000F is designed specifically for front mount applications, allowing for remarkable maneuverability and visibility. It is equipped with a robust frame that offers stability and durability, ideal for tackling rough terrain. The mower features a heavy-duty hammer blade design which effectively processes tough vegetation, ensuring a clean cut that enhances the aesthetic of any landscape. With a cutting width of 60 inches, it can cover substantial ground in a single pass, increasing productivity and efficiency.

On the other hand, the FSW6000T is a traditional rear mount flail mower that incorporates the same high-quality construction and functionality. This model is perfect for larger open areas where a rear-mounted option is preferred. It boasts an adjustable cutting height, allowing operators to adapt to various mowing conditions and achieve precise results. The dual-direction cutting capability enhances versatility, making it suitable for a wide range of applications from pasture management to roadside maintenance.

Both models utilize advanced technologies, including a unique suspension system that absorbs shocks and vibrations, ensuring a smoother operation and reduced wear on the machine. The heavy-duty rotor design guarantees uniform cutting even at higher speeds, while the efficient belt drive system minimizes power loss and maximizes performance.

Safety is also a priority with Woods Equipment, and both models are equipped with features such as PTO shields, which help to protect operators during operation. The ease of maintenance is another key characteristic, with readily accessible components allowing for quick service and minimal downtime.

In conclusion, the Woods Equipment FSW6000F and FSW6000T flail mowers represent cutting-edge technology and practical design, tailored to meet the rigorous demands of landscape and agricultural work. With their robust features, smart engineering, and superior performance, they stand out as reliable tools for anyone in need of effective mowing solutions.