Woods Equipment FSW6000T, FSW6000F Service, Lubrication, Chain Adjustment, Description Frequency

Page 10

SERVICE

A CAUTION

„Always wear relatively tight and belted clothing to avoid getting caught in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate.

A WARNING

„Before performing any service or maintenance, lower attachment to ground, turn off power unit engine, remove key, and disconnect battery ground cable (negative -).

„Never place any part of the body underneath implement/attachment or between its moving parts even when the engine has been turned off. Service work does not require going underneath unit. Mechanical failures, electrical failures, or operating controls can cause equipment to drop.

LUBRICATION

To prevent excessive wear, do not let excess grease collect on or around parts. Figure 1 shows the lubrica- tion points. The accompanying chart gives the fre- quency of lubrication in operating hours based on normal operating conditions. Severe or unusual condi- tions may require more frequent lubrication.

In addition to these lubrication points, lightly oil all roller chains periodically.

Check the oil level in gearboxes periodically. Maintain oil level to the bottom of fill plug hole. Use SAE 90W oil.

CHAIN ADJUSTMENT

Check periodically for proper chain tension between gearboxes. If chain tightening is required, loosen the four mounting bolts on the right gearbox and slide the gearbox to the right until proper chain tension is achieved. Do not overtighten chain.

A WARNING

„Make sure shields and guards are properly installed and in good condition. Replace if damaged.

NOTE: When performing any maintenance or making adjustments to the Sweeper broom, refer to the Sweepster) operator's manual.

Ref.

Description

Frequency

 

 

 

1

Guage Wheel Pivot (2 fittings)

8 Hours

 

 

 

2

Gauge Wheel (2 fittings)

8 Hours

 

 

 

3

Broom Pivot (2 fitttings)

40 Hours

 

 

 

4

Power Shafts (6 fittings)

8 Hours

 

 

 

3

4

1

2

CD3882

4

Figure 1. Lubrication Points

8 Service

MAN0118 (Rev. 12/23/2004)

 

Page 9 Page 11
Image 10
Page 9 Page 11
Contents MOW’N Machine Sweeper Ii Introduction To the DealerTable of Contents IntroductionTraining SafetySafety Rules PreparationTransportation MaintenanceStorage Safety & Instructional Decals Be Careful33347E Operation OperationPRE-OPERATION Check List Uneven TerrainOwner Responsibility Chain Adjustment ServiceService LubricationFixed Angle Mount KIT Installation AssemblyAssembly Dealer SET-UP InstructionsWAY Angle Mount KIT Holes in Sweepster ShieldWAY Angle Wiring Instructions Attaching Sweeper to TractorIgnition Purple PRE-DELIVERY Check List Dealer Check ListDealer Check Lists Delivery Check ListWAY Angle Sweeper Assembly PartsREF Part Description Fixed Angle Sweeper Mount KIT Assembly Part QTY DescriptionWAY Angle Sweeper Wire Diagram Typical Washer Installations Bolt Torque ChartSAE Series Torque Chart AppendixBolt Size Chart AbbreviationsLimited Warranty What is Covered MAN0118 Woods Equipment Company

FSW6000F, FSW6000T specifications

Woods Equipment is a renowned manufacturer of high-quality agricultural and landscaping equipment, and the FSW6000F and FSW6000T are prime examples of their commitment to durable, efficient, and innovative design. These flail mowers are engineered to cater to the needs of both professionals and enthusiasts in the agricultural and landscaping sectors.

The FSW6000F is designed specifically for front mount applications, allowing for remarkable maneuverability and visibility. It is equipped with a robust frame that offers stability and durability, ideal for tackling rough terrain. The mower features a heavy-duty hammer blade design which effectively processes tough vegetation, ensuring a clean cut that enhances the aesthetic of any landscape. With a cutting width of 60 inches, it can cover substantial ground in a single pass, increasing productivity and efficiency.

On the other hand, the FSW6000T is a traditional rear mount flail mower that incorporates the same high-quality construction and functionality. This model is perfect for larger open areas where a rear-mounted option is preferred. It boasts an adjustable cutting height, allowing operators to adapt to various mowing conditions and achieve precise results. The dual-direction cutting capability enhances versatility, making it suitable for a wide range of applications from pasture management to roadside maintenance.

Both models utilize advanced technologies, including a unique suspension system that absorbs shocks and vibrations, ensuring a smoother operation and reduced wear on the machine. The heavy-duty rotor design guarantees uniform cutting even at higher speeds, while the efficient belt drive system minimizes power loss and maximizes performance.

Safety is also a priority with Woods Equipment, and both models are equipped with features such as PTO shields, which help to protect operators during operation. The ease of maintenance is another key characteristic, with readily accessible components allowing for quick service and minimal downtime.

In conclusion, the Woods Equipment FSW6000F and FSW6000T flail mowers represent cutting-edge technology and practical design, tailored to meet the rigorous demands of landscape and agricultural work. With their robust features, smart engineering, and superior performance, they stand out as reliable tools for anyone in need of effective mowing solutions.
Top Page Image Contents