Woods Equipment BW180HBQ, BW126HBQ manual PRE-OPERATION Check List, Owners Responsibility

Page 18

STORAGE

Follow these steps when storing your cutter:

1.Clean cutter before storing. See page 23 for cleaning instructions. Store on level, solid ground.

2.Disconnect driveline and secure up off the ground.

3.Lower wings to ground.

4.Raise cutter center section and pin transport bar in raised position.

5.Attach parking jack and raise tongue weight off tractor drawbar.

6.Place wedge blocks at front and rear of wheels on center section and each wing to prevent wheel rotation.

7.Securely block all four corners of center section and each wing with jack stands.

8.Remove hydraulic hoses after tractor is turned off and all system pressure is released by operating valve levers several times.

9.Remove safety tow chain.

10.Remove retainer pin and high strength drawbar pin.

11.Keep children and bystanders away from storage area.

PRE-OPERATION CHECK LIST

(OWNER'S RESPONSIBILITY)

___ Review and follow all safety rules and safety decal instructions on page 7 through page 13.

___ Check that all safety decals are installed and in good condition. Replace if damaged.

___ Check that equipment is properly and securely attached to tractor.

___ Make sure driveline spring-activated locking pin or collar slides freely and is seated firmly in trac- tor PTO spline groove.

___ Check all lubrication points and grease as instructed in lubrication information. Make sure

 

the PTO slip joint is lubricated and that the gear-

 

box fluid levels are correct.

___

Set tractor PTO at correct rpm for your equip-

 

ment.

___

Lubricate all grease fitting locations. Make sure

 

PTO shaft slip joint is lubricated.

___

Check that all hydraulic hoses and fittings are in

 

good condition and not leaking before starting

 

tractor. Check that hoses are not twisted, bent

 

sharply, kinked, frayed, or pulled tight. Replace

 

any damaged hoses immediately.

___

Check that all hardware is properly installed and

 

secured.

___

Check cutting height and attitude adjustment.

___

Raise and lower equipment to make sure air is

 

purged from hydraulic cylinders and hoses. Raise

 

and lower equipment to make sure air is purged

 

from hydraulic cylinders and hoses.

___

Check that blades are sharp and secure and cut-

 

ting edge is positioned to lead in a counterclock-

 

wise rotation.

___

Make sure tractor ROPS or ROPS cab and seat

 

belt are in good condition. Keep seat belt

 

securely fastened during operation.

___ Check that shields and guards are properly installed and in good condition. Replace if dam- aged.

___ Before starting engine, operator must be in trac- tor seat with seat belt fastened. Place transmis- sion in neutral or park, engage brake and disengage tractor PTO.

___ Inspect area to be cut and remove stones, branches, or other hard objects that might be

 

thrown and cause injury or damage.

___

Inspect rubber or chain shielding and replace any

 

damaged rubber shield or missing links.

___

Make sure tractor 3-point lift links do not interfere

 

with hydraulic hoses or driveline throughout full

 

turning range.

18 Operation

MAN0805 (4/30/2009)

 

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Batwing Introduction To the DealerTable of Contents LEA EL InstructivoSpecifications General InformationBW180HD, BW180HB, BW126HB Free Mower Safety Video SafetyTraining Package for Rotary Mowers/Cutters-English Training Package for Rotary Mowers/Cutters-English/SpanishTraining Safety RulesInstallation PreparationTransportation OperationMaintenance Storage Safety & Instructional Decals Be CarefulPN 1006348 Located on Wheel Rims 1000 RPM PN 15922 1000 RPM PN 18866 540 RPMSafety Operation Connecting Cutter to TractorOperation Hydraulic ConnectionCV Driveline Turning Limits Cutting Height AdjustmentInterference Check Tractor OperationCutter Operation Mowing TipsShredding Wing Lock-Up TransportingLock-Up Center Section Lock-UpPRE-OPERATION Check List Owners ResponsibilityOwner Service Owner ServiceBlocking Method Lubrication Gearbox LubricationDriveline Lubrication Blades Blade Installation FigureSeasonal Lubrication Blade Removal FigureSlip Clutch Adjustment Figure Blade SharpeningCleaning Shielding RepairServicing Tires Safely Troubleshooting TroubleshootingGearbox Maintenance Dealer ServiceDealer Service Seal Replacement FigureDisassembly Figure Gearbox RepairRemoval from Cutter Figure Reinstallation GearboxDisassembly AssemblySplitter Gearbox Repair Figure Removal from Cutter Reinstallation on Cutter Check GearboxCrossbar Removal Crossbar RemovalCrossbar Installation Joint DisassemblyUniversal Joint Repair Joint Assembly Assembly Assembly InstructionsDealer SET-UP Instructions Install Height Adjustment Cylinder BW180HD Install SMV Emblem BW180HDInstall Wheel and Hub BW180HD Install Tongue BW180HDInstall 3-Joint Drive 540 RPM Only BW180HD Joint Drive InstallationInstall CV Drive BW180HD- Optional Install Wing BW180HDInstall Wing Cylinder & Lock-up Bar BW180HD Install Wing Wheel and Hub All Models Left Wing Lock-Up Bar InstalledInstall Hose Kit BW180HD Install Wing Wheel Yoke Adjustment Link BW180HDInstall Wing Driveline BW180HD Winch Kit Installation OptionalInstall Chain or Belt Shielding BW180HD Chain Shielding Installation Center SectionChain Shielding Installation Right Wing Shown Belt Shielding Installation Right Wing PRE-DELIVERY Check List Dealer Check ListsDealer Check Lists Delivery Check ListMAN0805 4/30/2009 Parts BW180HD, BW180HDQ BW180HB, BW180HBQ BW126HB, BW126HBQMain Frame Assembly Front Section Part QTY Description BW180HD Main Frame Assembly Rear Section Tire & hub see BW180HB Main Frame Assembly Rear Section REF Part QTY Description Wing Assembly See Wing & Center Gearbox Assembly Center Right Wing Left Wing DescriptionSplitter Gearbox Assembly Gear, 540 rpmCenter Deck Drive Assembly Front Drive Assembly Equal Angle Rear Drive Assembly Equal Angle RPM & 1000 RPM Front CV Drive Wing Drive Assembly Bolt Wheel & Tire Assembly 1027468 Rubber Shielding Wing Front & Rear Standard on BW180 Models Chain Shielding Center Section Front & Rear Single ROW Double ROWChain Shielding Wing Front & Rear Single ROWHydraulic Cylinders Crossbar Puller Optional Hydraulic Cylinder Stroke Control KITBW126HB / BW126HBQ Weight BOX Assembly Optional Winch Kit Installation Winch KIT OptionalWinch Kit Operation Appendix Bolt Torque ChartSAE Series Torque Chart Metric SeriesBolt Size Chart AbbreviationsIndex IndexWarranty Rev /23/2005 Woods Equipment Company

BW126HBQ, BW126HB, BW180HBQ specifications

Woods Equipment is renowned for its dedication to high-quality agricultural equipment, and the BW126HB, BW180HBQ, and BW126HBQ models exemplify this commitment. These models are designed for various applications, ensuring they meet diverse farming and landscaping needs.

The Woods BW126HB is a robust and versatile brushcutting mower designed for heavy-duty use. It features a 12-foot working width, enabling operators to cover large areas quickly and efficiently. This model is equipped with a powerful hydraulic drive system that enhances performance and reduces maintenance needs. The durable design includes a reinforced frame and high-strength cutting blades, ensuring exceptional performance even in challenging conditions. The adjustable cutting height allows for customizing the mowing experience, making it suitable for different terrains and vegetation types.

Next, the BW180HBQ model is geared towards high-capacity operations. With an impressive 15-foot working width, it is ideal for large-scale land management tasks. This model features an innovative Quick Attach System, allowing for fast attachment and detachment from various tractors. The advanced cutting technology employed in the BW180HBQ ensures a clean cut, promoting healthier growth of the remaining grass. Additionally, its steel construction and corrosion-resistant coating enhance durability and longevity, making it a wise investment for any agricultural operation.

The Woods BW126HBQ combines the benefits of the BW126HB with added versatility. This model is a quad-mount design that provides operators with improved stability and control. Equipped with a 12-foot cutting width, it seamlessly handles larger areas while still being able to navigate tight spots. Its dual hydraulic motors enable enhanced power efficiency, reducing fuel consumption while maximizing productivity. The innovative blade system incorporated in the BW126HBQ allows for superior mulching capabilities, further enhancing its utility for land management and landscaping.

All three models showcase Woods Equipment's dedication to user-friendly features. Each mower is designed with easy-to-reach controls and intuitive operation, ensuring a smooth experience for operators of all skill levels. The incorporation of advanced technologies, such as enhanced cutting efficiency and reduced noise operation, showcases Woods’ commitment to innovation.

In summary, the Woods BW126HB, BW180HBQ, and BW126HBQ models are exemplary options for those seeking high-performing brushcutting solutions. Each model has unique features and capabilities, making them suitable for various agricultural tasks. Their durability, efficiency, and user-friendly designs highlight Woods Equipment's mission to provide exceptional machinery for modern farming and landscaping needs.
Top Page Image Contents