Woods Equipment BW180HBQ, BW126HBQ manual Reinstallation, Gearbox

Page 27

correct diameter. Be sure not to damage the seal lip.

8.Press in housing so that seal is recessed. Press protective seal (8) until seated flush with housing. Verify that the seal (8) is seated correctly.

9.Press bearing (7) into the housing, using a round tube of the correct diameter and a hand press. Secure with shim (13) and snap ring (10).

10.Secure snap ring (11) on input shaft (3) if not already secure.

11.Place gear (1) through top of housing and align gear (1) and gear (5) so that gear teeth are a match.

12.While holding gear (1) in place, slide input shaft (3) through gear (1) and bearing (7). Align splines on shaft (3) and gear (1).

13.Slide shim (12) over input shaft (3) and press bearing (7) onto input shaft (3), using a round tube of the correct diameter and a hand press.

14.Slide shim (13) over input shaft (3) and secure with snap ring (10).

15.Check input shaft end float by moving the input shaft (3) by hand. If end float is higher than 0.012", insert shim between input shaft (3) and rear bearing (7). Repeat until end float is less than

0.012". Check rotational torque by hand. The torque should be less than 2.2 lbs-inch.

16.Check that the gear backlash is between 0.006" and 0.016". You should not have to adjust the backlash.

17.Press in input oil seal (19), using tube of correct diameter. Be careful not to damage seal lip.

18.Press oil cap (20) on to cover the rear of housing, using a tube of the correct diameter.

19.Place top cover (22) on top of housing and secure with six cap screw (23).

20.Check gearbox housing for leaks by plugging all holes except one. Apply 4 psi compressed air and immerse the gearbox in water to verify that there are no leaks.

21.Remove gearbox from water and dry off with compressed air. Add SAE 80W or 90W EP oil until it runs out of side level hole. Tighten all plugs.

Reinstallation

NOTE: Gearbox is heavy: do not attempt to move with- out mechanical assistance.

1.Set gearbox on cutter and fasten with bolts and nuts. Torque bolts to 300 lbs-ft.

2.Attach crossbar (Crossbar Installation, page 31).

1.

Crown gear

22.

Top cover

2.

Gearbox housing

23.

Cap screw 8 mm x 16 (8.8)

3.

Input shaft

24.

Vent plug

4.

Output shaft

25.

Cotter pin

5.

Gear pinion

26.

Washer

6.

Bearing

27.

Side plug

7.

Input bearing

 

 

8.

Protective seal

 

 

9.

Cotter pin

 

 

10.

Snap ring

 

 

11.

Snap ring

 

 

12.

Shim, 45.3 x 2.5

 

 

13.

Shim, 70.3 x 84.7

 

 

14.

Nut

 

 

15.

Castle nut

 

 

16.

Shim, 50.3 x 70.3

 

 

17.

Shim

 

 

18.

Oil seal (Vertical Shaft)

 

 

19.

Oil seal (Horizontal Shaft)

 

 

20.

Cap

 

 

21.

Bearing

 

 

Figure 13. Gearbox

MAN0805 (4/30/2009)

Dealer Service 27

 

 

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Batwing To the Dealer IntroductionLEA EL Instructivo Table of ContentsSpecifications General InformationBW180HD, BW180HB, BW126HB Safety Free Mower Safety VideoTraining Package for Rotary Mowers/Cutters-English/Spanish Training Package for Rotary Mowers/Cutters-EnglishPreparation Safety RulesInstallation TrainingOperation TransportationMaintenance Storage Safety & Instructional Decals Be CarefulPN 1006348 Located on Wheel Rims PN 15922 1000 RPM PN 18866 540 RPM 1000 RPMSafety Hydraulic Connection Connecting Cutter to TractorOperation OperationTractor Operation Cutting Height AdjustmentInterference Check CV Driveline Turning LimitsCutter Operation Mowing TipsShredding Center Section Lock-Up TransportingLock-Up Wing Lock-UpOwners Responsibility PRE-OPERATION Check ListOwner Service Owner ServiceBlocking Method Lubrication Gearbox LubricationDriveline Lubrication Blade Removal Figure Blade Installation FigureSeasonal Lubrication BladesBlade Sharpening Slip Clutch Adjustment FigureCleaning Shielding RepairServicing Tires Safely Troubleshooting TroubleshootingSeal Replacement Figure Dealer ServiceDealer Service Gearbox MaintenanceDisassembly Figure Gearbox RepairRemoval from Cutter Figure Gearbox ReinstallationDisassembly AssemblySplitter Gearbox Repair Figure Removal from Cutter Check Gearbox Reinstallation on CutterCrossbar Removal Crossbar RemovalCrossbar Installation Joint DisassemblyUniversal Joint Repair Joint Assembly Assembly Assembly InstructionsDealer SET-UP Instructions Install SMV Emblem BW180HD Install Height Adjustment Cylinder BW180HDInstall Tongue BW180HD Install Wheel and Hub BW180HDJoint Drive Installation Install 3-Joint Drive 540 RPM Only BW180HDInstall CV Drive BW180HD- Optional Install Wing BW180HDInstall Wing Cylinder & Lock-up Bar BW180HD Left Wing Lock-Up Bar Installed Install Wing Wheel and Hub All ModelsWinch Kit Installation Optional Install Wing Wheel Yoke Adjustment Link BW180HDInstall Wing Driveline BW180HD Install Hose Kit BW180HDChain Shielding Installation Center Section Install Chain or Belt Shielding BW180HDChain Shielding Installation Right Wing Shown Belt Shielding Installation Right Wing Delivery Check List Dealer Check ListsDealer Check Lists PRE-DELIVERY Check ListMAN0805 4/30/2009 BW180HD, BW180HDQ BW180HB, BW180HBQ BW126HB, BW126HBQ PartsMain Frame Assembly Front Section Part QTY Description BW180HD Main Frame Assembly Rear Section Tire & hub see BW180HB Main Frame Assembly Rear Section REF Part QTY Description Wing Assembly See Wing & Center Gearbox Assembly Right Wing Left Wing Description CenterGear, 540 rpm Splitter Gearbox AssemblyCenter Deck Drive Assembly Front Drive Assembly Equal Angle Rear Drive Assembly Equal Angle RPM & 1000 RPM Front CV Drive Wing Drive Assembly Bolt Wheel & Tire Assembly 1027468 Rubber Shielding Wing Front & Rear Standard on BW180 Models Single ROW Double ROW Chain Shielding Center Section Front & RearSingle ROW Chain Shielding Wing Front & RearHydraulic Cylinders Hydraulic Cylinder Stroke Control KIT Crossbar Puller OptionalBW126HB / BW126HBQ Weight BOX Assembly Optional Winch Kit Installation Winch KIT OptionalWinch Kit Operation Metric Series Bolt Torque ChartSAE Series Torque Chart AppendixAbbreviations Bolt Size ChartIndex IndexWarranty Rev /23/2005 Woods Equipment Company

BW126HBQ, BW126HB, BW180HBQ specifications

Woods Equipment is renowned for its dedication to high-quality agricultural equipment, and the BW126HB, BW180HBQ, and BW126HBQ models exemplify this commitment. These models are designed for various applications, ensuring they meet diverse farming and landscaping needs.

The Woods BW126HB is a robust and versatile brushcutting mower designed for heavy-duty use. It features a 12-foot working width, enabling operators to cover large areas quickly and efficiently. This model is equipped with a powerful hydraulic drive system that enhances performance and reduces maintenance needs. The durable design includes a reinforced frame and high-strength cutting blades, ensuring exceptional performance even in challenging conditions. The adjustable cutting height allows for customizing the mowing experience, making it suitable for different terrains and vegetation types.

Next, the BW180HBQ model is geared towards high-capacity operations. With an impressive 15-foot working width, it is ideal for large-scale land management tasks. This model features an innovative Quick Attach System, allowing for fast attachment and detachment from various tractors. The advanced cutting technology employed in the BW180HBQ ensures a clean cut, promoting healthier growth of the remaining grass. Additionally, its steel construction and corrosion-resistant coating enhance durability and longevity, making it a wise investment for any agricultural operation.

The Woods BW126HBQ combines the benefits of the BW126HB with added versatility. This model is a quad-mount design that provides operators with improved stability and control. Equipped with a 12-foot cutting width, it seamlessly handles larger areas while still being able to navigate tight spots. Its dual hydraulic motors enable enhanced power efficiency, reducing fuel consumption while maximizing productivity. The innovative blade system incorporated in the BW126HBQ allows for superior mulching capabilities, further enhancing its utility for land management and landscaping.

All three models showcase Woods Equipment's dedication to user-friendly features. Each mower is designed with easy-to-reach controls and intuitive operation, ensuring a smooth experience for operators of all skill levels. The incorporation of advanced technologies, such as enhanced cutting efficiency and reduced noise operation, showcases Woods’ commitment to innovation.

In summary, the Woods BW126HB, BW180HBQ, and BW126HBQ models are exemplary options for those seeking high-performing brushcutting solutions. Each model has unique features and capabilities, making them suitable for various agricultural tasks. Their durability, efficiency, and user-friendly designs highlight Woods Equipment's mission to provide exceptional machinery for modern farming and landscaping needs.
Top Page Image Contents