Changing the Transmission OIL President Pro16 Pro18

GBENGLISH

Check the oil every time when topping up. The level should come up to the “FULL” mark.

CHANGING THE TRANSMISSION OIL (President - Pro16 - Pro18)

Change the oil the first time after 50 hours of oper- ation, and then after every 250 hours or operation or once a season.

Use a good grade of SAE 20W-50 oil (service grade SE, SF or SG).

Total amount of oil: President - 1.6 litres Pro16, Pro18 - 3.3 litres

NOTE that the design of the transmission per- mits only about 80% of the total amount of oil to run out when the oil is changed.

After filling the transmission with oil, the oil which is left in the transmission mixes with the new oil.

You should, therefore, not pour in too much oil when you change the oil. Check the oil level sev- eral times while filling.

It is important that you observe clean- ness when handling oil for the transmis- sion. There must not be any particles of dirt in the system as dirt can easily cause total failure of the transmission.

President:

1.Unscrew the oil drain plug D. This is located to the right as viewed from the rear (figs 14 and 25). Allow the oil to run out into a collection vessel.

2.Screw the oil drain plug back into place.

3.Remove the oil dipstick and top up with new oil.

Pro16-Pro18:

1.Remove the oil reservoir cover (fig 10).

2.Unscrew the oil drain plug E. This is located to the left as viewed from the rear (figs 15 and 26). Allow the oil to run out into a collection vessel.

3.Screw the oil drain plug back into place.

4.Remove hose F from the lower side of the oil reservoir (fig 16).

5.To facilitate filling up the oil, we recommend that you use, for example, a pump (figure 16 shows a STIGA pump, part number 1134-3898-01).

6.Fill the pump with oil. Then insert the nipple into the hose F and slowly press the oil into the

transmission.

7.Connect the hose to the oil reservoir.

8.Finally, fill the oil reservoir with oil.

AIR BLEEDING (President - Pro16 - Pro18)

After filling with oil, it may be necessary to bleed the transmission.

1.Raise the rear part of the machine to enable the drive wheels to rotate freely.

2.Start the engine and allow it to idle.

3.Press the drive pedal down forwards and back- wards alternately.

4.When the drive wheels start to rotate, lower the machine down onto its wheels.

5.Push the machine backwards while pushing the front part of the drive pedal down. Then push the machine forwards while pushing the rear part of the drive pedal down.

6.When the machine starts to move, put the throt- tle control at full throttle.

7.Start and stop the machine rapidly until its speed is normal.

Remarks: Initial bleeding can be made as early as when filling with oil. While filling, rotate the transmission's belt pulley by hand.

REPLACING ENGINE OIL FILTER (Pro16 - Pro18)

Replace the oil filter after every 100 hours of oper- ation.

Before screwing the new filter securely into place, oil the filter gasket with motor oil.

Screw the filter G securely by hand until the filter gasket touches the filter attachment. Then tighten three-quarters of a full turn (fig 13).

Start the engine and run it for 30 seconds. Then switch off the engine. Check the oil level. If the oil level is below the “FULL” mark on the dipstick, top up with oil.

Start the engine and check for any oil leakage.

LUBRICATION

The machine has four grease nipples H which should be lubricated with universal grease every

PRO 18, PRO 16 specifications

Stiga PRO 16 and PRO 18 are elite-level table tennis blades that exemplify exceptional craftsmanship and cutting-edge technology, targeting both competitive players and serious enthusiasts. These blades are meticulously designed for players who seek balance, power, and control, integrating various innovative features that contribute to superior performance on the table.

The Stiga PRO 16 is particularly known for its lightweight design paired with a high degree of stiffness. This blade employs a unique combination of multiple layers of wood and advanced composite materials that enhance speed while maintaining excellent control. Its 16 mm thickness strikes a harmony between power and precision, allowing players to deliver fierce shots with ease. The PRO 18, on the other hand, is slightly thicker at 18 mm, providing a more substantial feel and increased power for aggressive playstyles. This thicker build enables players to generate greater spin, making it a favored choice for those who rely on heavy topspin and fast-paced gameplay.

Both blades feature the renowned Stiga “WAVE” technology, which optimizes the wood grain orientation to maximize speed and minimize vibrations. This technology not only enhances ball feel but also improves the racket's stability during intense rallies. Additionally, they come equipped with Stiga's proprietary “Hyper Bounce” technology, ensuring that players experience consistent rebound characteristics, enabling them to execute precise strokes without compromising power.

Another defining characteristic of the Stiga PRO 16 and PRO 18 is their ergonomic handle design. Both blades feature a well-shaped handle that fits comfortably in hand, allowing for extended playing periods without fatigue. Players can personalize their experience further by choosing between different handle types, such as the Straight, Flared, or Concave designs.

Moreover, both blades are compatible with a wide range of rubber surfaces, granting players the freedom to customize their setup according to their unique preferences. The combination of these features results in blades that not only cater to advanced techniques but also enhance overall playing experience.

In conclusion, the Stiga PRO 16 and PRO 18 represent the pinnacle of table tennis technology. Their high-quality materials, advanced technologies, and thoughtful design ensure players possess the necessary tools to take their game to new heights. These blades are not just products; they are a gateway to elevated performance on the table.