McIntosh XRT2K owner manual How to Connect using three Amplifiers

Page 18

How to Connect using three Amplifiers

Caution: The AC Power Cord should not be connected to the Power Amplifier until after the Loudspeaker Connections have been made. Failure to observe this could result in Electric Shock.

1.Prepare two 14 inch (35.6cm) Jumper Wires for connecting the Low Frequency Column, Lower and Upper Sections together by choosing one of the methods below:

Bare wire cable ends:

Carefully remove sufficient insulation from the cable ends, refer to figures 12, 13 & 14. If the cable

is stranded, carefully twist the strands to-

gether as tightly as possible.

Note: If desired, the twisted ends can be tinned with solder to keep the strands together or attach spade lugs.

Spade lug or prepared wire connection: Insert the spade lug connector or prepared section of the cable end into the terminal side access hole, and tighten the terminal cap until the cable is firmly clamped into the terminal so the wires cannot slip out. Refer to figures 15, 16 & 17.

2.Connect 14 inch Jumper Wires from the Low Frequency Column Upper Section (-) and (+) Binding Posts to the Low Frequency Column

Lower Section (-) and (+) Binding Posts.

Note: It is important to maintain the correct polarity at both ends of the Loudspeaker cables.

3.Connect Loudspeaker cables from the XRT2K HIGH Frequency INPUTS 3 (-) and (+) Bind- ing Posts on the Low Frequency Column Lower Section to the (-) and (8 ohm) Binding Posts A of the Power Amplifier number two.

4.Connect Loudspeaker cables from the XRT2K HIGH Frequency INPUTS 2 (-) and (+) Bind- ing Posts on the Low Frequency Column Lower Section to the (-) and (8 ohm) Binding Posts B of the Power Amplifier number three.

5.Connect Loudspeaker cables from the XRT2K HIGH Frequency INPUTS 1 (-) and (+) Bind- ing Posts on the Low Frequency Column Lower Section to the (-) and (8 ohm) Binding Posts C of the Power Amplifier number three.

6.Connect Loudspeaker cables from the XRT2K MID Frequency INPUTS 3 (-) and (+) Binding Posts on the Low Frequency Column Lower Section to the (-) and (8 ohm) Binding Posts A of the Power Amplifier number three.

7.Connect Loudspeaker cables from the XRT2K MID Frequency INPUTS 2 (-) and (+) Binding Posts on the Low Frequency Column Lower Section to the (-) and (8 ohm) Binding Posts B of the Power Amplifier number two.

8.Connect Loudspeaker cables from the XRT2K MID Frequency INPUTS 1 (-) and (+) Binding Posts on the Low Frequency Column Lower Section to the (-) and (8 ohm) Binding Posts C of the Power Amplifier number two.

9.Connect Loudspeaker cables from the XRT2K LOW Frequency INPUTS 3 (-) and (+) Binding Posts on the Low Frequency Column Lower Section to the (-) and (8 ohm) Binding Posts A of the Power Amplifier number one.

10.Connect Loudspeaker cables from the XRT2K LOW Frequency INPUTS 2 (-) and (+) Binding Posts on the Low Frequency Column Lower Section to the (-) and (8 ohm) Binding Posts B of the Power Amplifier number one.

11.Connect Loudspeaker cables from the XRT2K LOW Frequency INPUTS 1 (-) and (+) Binding Posts on the Low Frequency Column Lower Section to the (-) and (8 ohm) Binding Posts C of the Power Amplifier number one.

12.Tighten all of the Loudspeaker and Amplifier Binding Posts.

13.Connect the remaining XRT2K Loudspeaker(s) and Power Amplifier Channel(s) in the same manner.

McIntosh MC2KW Power Amplifier number three

McIntosh MC2KW Power Amplifier number two

18

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents XRT2K Important Safety Instructions Table of Contents Safety Instructions Thank YouCustomer Service Please Take a MomentIntroduction Introduction and Performance Features Performance FeaturesLoudspeaker System Side View DimensionsFront View Loudspeaker SystemXRT2K Dimensions, con’t Unpacking the Low Frequency Column Lower Section Unpacking and AssemblyUnpacking the Midrange/High Frequency Column Unpacking the Low Frequency Column Upper SectionFinal Assembly of the Loudspeaker Room Placement Locating Loudspeakers for use in Home TheaterPage Low Frequency Column Rear Panel Connections How to Connect using a single Amplifier To the 8 ohm Binding Post C of the Power AmplifierMcIntosh MC2KW Power Amplifier Inch 35.6cm Jumper Wires How to Connect using two Amplifiers How to Connect using two Amplifiers How to Connect using three Amplifiers How to Connect using three Amplifiers Page Photos Specifications Specifications General SpecificationsPacking Instructions McIntosh Laboratory, Inc Chambers Street Binghamton, NY

XRT2K specifications

The McIntosh XRT2K stands as a monumental achievement in the world of high-fidelity loudspeakers, reflecting the brand's commitment to superior sound engineering and aesthetic design. Known for its distinctive look and powerful performance, this model blends cutting-edge technology with timeless craftsmanship, appealing to audio enthusiasts and professionals alike.

One of the most significant features of the XRT2K is its innovative speaker configuration. The design incorporates an array of drivers, including a high-frequency section with multiple tweeters that ensure detailed, clear highs. This is complemented by mid-range drivers that provide a full-bodied representation of vocals and instruments. The lower section features powerful woofers designed to deliver deep, controlled bass, creating a three-dimensional soundstage that envelops listeners.

The XRT2K utilizes McIntosh's proprietary techniques, such as its advanced driver alignment, which ensures precise timing and phase coherence across the audio spectrum. This results in an immersive listening experience where every note is accurately reproduced, maintaining the integrity of the original recording. The speaker’s unique design also minimizes unwanted resonances and distortions, allowing for a cleaner and more accurate sound.

Another standout characteristic of the XRT2K is its broad frequency response, which enables it to reproduce a wide range of musical genres effortlessly. Whether one is enjoying classical music with its intricate detail or high-energy rock tracks with throbbing bass, the XRT2K can handle it all without compromise. The depth of the soundstage is further enhanced by the speaker's ability to convey spatial information, allowing listeners to feel as though they are in the same room as the performers.

In terms of aesthetics, the XRT2K epitomizes luxury. Its sleek, modern design is complemented by iconic McIntosh styling, featuring glass panels, polished aluminum, and the signature blue VU meters. This not only makes it a visually striking addition to any audio setup but also matches well with high-end AV systems and home theaters.

Overall, the McIntosh XRT2K is a remarkable fusion of technology, craftsmanship, and design. With its advanced driver technology, meticulous engineering, and striking aesthetics, it stands out in the luxury audio market, promising an unparalleled listening experience that can satisfy the most discerning audiophiles.
Top Page Image Contents