Sterling Plumbing SP1500D Series manual Tools and Materials, Before You Begin

Page 2

Tools and Materials

Tape				Claw
Measure	Pencil	Safety Glasses	Drill	Hammer	Caulk Gun

Phillips	Silicone	Center	Miter Saw or Hack Saw with
Screwdriver	Sealant	Punch	32-teeth Per Inch Blade
Scissors	File	Masking Tape	Level

Miter Box

Plus:

•Drop Cloth

•Petroleum Jelly

Before You Begin

CAUTION: Risk of personal injury. Always wear safety glasses when cutting materials.

IMPORTANT! Pay special attention to the section titled ″Very Important Instructions.″ Failure to follow the directions could result in product damage.

IMPORTANT! This shower door is designed to be speciﬁcally paired with a Sterling shower module. Do not install this shower door if you do not have a Sterling shower module installed.

IMPORTANT! Record the model number on the Homeowners Guide if you intend to save it, or in your records for later use. The proper model number will enable our customer service representatives to quickly help you if needed.

NOTE: When using a retractable case tape measure, add the length of the case to the measurement or measure in a manner that excludes the case.

Your new Sterling door can be installed with the door opening to either the right or left. Install the door with the pivot side away from the showerhead for best results.

Before starting the installation, lay out and identify all of the parts. Inspect them for damage.

Closely follow the instructions pertaining to the sealant application on the door. Sealing areas other than those shown may cause leaking.

Two people should perform this installation.

Sterling reserves the right to make revisions to the design of products without notice, as speciﬁed in the Price Book.

1034026-2-D

2

Sterling

Image 2

Contents Installation Guide Tools and Materials Before You BeginParts Identiﬁcation Very Important Instructions Determine the Door Conﬁguration Measure and Cut the Bottom Track BaseLocate the Bottom Track Install the ″U″ ChannelInstall the U-Channel Locate the Bottom TrackMark the Wall Jamb Locations Prepare the Wall Jamb LocationsCaulk and Install the Bottom Track Seal the Bottom TrackCaulk the Bottom Track and Wall Jambs Install the Wall JambsInstall the Wall Jambs Measure and Cut the Top Track Install the BlocksCut the Top Track Install the Pivot Block Install the Top Track Install the Top TrackInstall the Strike Expander Jamb Install the Strike Expander JambInstall the Fixed Panel Install the Fixed GlassInstall the Bottom Pivot Install the Bottom PivotInstall the Top Pivot on the Door Panel Install the Top PivotInstall the Door Panel Install the Door PanelInstall the Bumper Plug Caulk the Shower Door From outside the showerOutils et matériels Avant de commencerIdentiﬁcation des pièces Instructions très importantes Déterminer la conﬁguration de la porte Mesurer et couper le rail inférieur Pour pivots droitsInstaller le profilé en U Installer le proﬁlé en ″U″Déterminer l’emplacement du rail inférieur Déterminer lemplacement du rail inférieurMarquer les emplacements du montant du mur Préparer les emplacements du montant du murAppliquer du mastic et installer le rail inférieur Mastiquer le rail inférieur Installer le rail inférieurMastiquer le rail inférieur Installer les montants du murInstaller les montants du mur Mesurer et couper le rail supérieur Installer les blocsInstaller le bloc du pivot Découper le rail supérieurInstaller le rail supérieur Installer le rail supérieurInstaller le montant de fermeture Installer le verre fixe Installer le montant de butée extensibleInstaller le panneau ﬁxe Installer le pivot inférieur Installer le pivot inférieurInstaller le pivot supérieur sur le panneau de la porte Installer le pivot supérieurInstaller le panneau de porte Installer le panneau de porteInstaller la butée Appliquer du mastic sur la porte de douche De l’extérieur de la doucheHerramientas y materiales Antes de comenzarIdentiﬁcación de las piezas ¡IMPORTANTE Instrucciones muy importantesDetermine la conﬁguración de la puerta Mida y corte el carril inferior Base en ÁnguloInstale el canal en U Instale el canal en ″U″Coloque el carril inferior Coloque el carril inferiorMarque el lugar de instalación de las jambas murales Prepare los lugares de instalación de las jambas muralesSelle e instale el carril inferior Selle el carril inferior Instale el carril inferiorInstale las jambas murales Instale las jambas muralesSelle el carril inferior y las jambas murales Selle el carril inferiorCorte el carril superior Mida y corte el carril superiorInstale los bloques Instale el carril superior Instale el carril superiorInstale la jamba de expansión de contacto Instale el panel ﬁjoInstale el pivote inferior Instale el pivote superior Instale el pivote inferiorInstale el pivote superior en el panel de la puerta Instale el panel de la puerta Instale el panel de la puertaInstale el tope Selle la puerta de ducha Desde el exterior de la ducha1034026-2-D 1034026-2-D By Kohler Co