Shindaiwa 82014, T2510X manual Stopping the Engine, Adjusting Engine Idle, When the Engine Starts

Page 10

Starting the Engine (continued)

WARNING!

The cutting attachment may rotate when the engine is started!

6.When the engine starts, slowly move the choke lever to the “OPEN” position. See Figure 20. (If the engine stops after the initial start, close the choke and restart.)

WARNING!

Never start the engine from the operating position.

7.Operating the throttle will automatically disengage the fast idle setting.

IMPORTANT!

If the engine fails to start after several attempts with the choke in the closed position, the engine may be flooded with fuel. If flooding is suspected,

move the choke lever to the open position and repeatedly pull the recoil starter to remove excess fuel and start the engine. If the engine still fails to start, refer to the troubleshooting section of this manual.

When the Engine Starts...

nAfter the engine starts, allow the engine to warm up at idle 2 or 3 minutes before operating the unit.

nAfter the engine is warm, pick

up the unit and clip on the shoulder strap if so equipped. See page 11.

nAdvancing the throttle makes the cutting attachment turn faster; releasing the throttle permits the attachment to stop turning. If the cutting attachment continues to rotate when the engine returns to idle, carburetor idle speed should be adjusted (see “Adjusting Engine Idle” below).

 

 

Open

Figure 20

 

 

 

 

 

Stopping the Engine

OFF

Figure 21

Adjusting Engine Idle

Idle the engine briefly before stopping (about 2 minutes), then slide the ignition switch to the “O” (Engine OFF) position.

 

Idle Adjusting

Figure 22

Screw

 

 

The engine must return to idle speed whenever the throttle lever is released. Idle speed is adjustable, and must be set low enough to permit the engine clutch to disengage the cutting attachment.

Idle Speed Adjustment

WARNING!

The cutting attachment must NEVER rotate at engine idle! If the idle speed cannot be adjusted by the procedure described here, return the trimmer to your Shindaiwa dealer for inspection.

1.Place the trimmer on the ground, then start the engine, and then allow it to idle 2-3 minutes until warm.

2.If the attachment rotates when the engine is at idle, reduce the idle speed by turning the idle adjustment screw counter-clockwise. See Figure 22.

3.If a tachometer is available, the engine idle speed should be final adjusted to 3,200 (±300) rpm (min-1).

4.Carburetor fuel mixture adjustments are preset at factory and cannot be serviced in the field.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents T2510 Trimmer T2510X Trimmer Contents IntroductionSafety Instructions Properly Equipped OperatorSafety Labels Be Aware of the Working EnvironmentAir cleaner type SpecificationsPrior to Assembly Product DescriptionAdjust Throttle Lever Free Play Assembly and AdjustmentsHandle Sub-Shield T2510X AssemblyCutting Attachment Shield Trimmer HeadNever operate the T2510X without the safety clip in place Blade T2510X Mount the Saw BladeStarting the Engine Mixing FuelFilling the Fuel Tank Examples of 501 mixing quantitiesIdle Speed Adjustment Adjusting Engine IdleWhen the Engine Starts Stopping the EngineShoulder Strap Checking Unit ConditionCutting Grass-Units Equipped with a Trimmer Head Brushcutter Handlebar Using a Blade T2510XBlade Thrust Brushcutter Shoulder StrapDaily Maintenance General MaintenanceHour Maintenance 10/15-Hour Maintenance Remove and replace the filter elementSpark Arrester Screen Maintenance 139/150-Hour MaintenanceValve Adjustment Shindaiwa Tornado Blade Long Term StorageBlade Sharpening Multiple-tooth Circular BladeTroubleshooting Guide Engine does not StartAdditional Problems This Warranty is Administered by Fax 503 81-82-849-2481 Notas POR Administrada ES Garantía Esta 19SPContinuacin Diagnostico Guia 18SPDiagnostico Guia 17SPMúltiples dientes de Discos Discos de AfiladoPlazo Largo de Almacenamiento Tornado Shindaiwa DiscoGuardachispas Maya la de Mantenimiento Mantenimiento o horas 139/150 CadaFiltro del elemento Horas 50 Cada MantenimientoHoras 10/15 Cada Mantenimiento El reemplace y RetireDiario Mantenimiento Horas-10 Cada MantenimientoGeneral Mantenimiento T2510X Disco un Usando Hombro de Correa Corte de Cabezal con Equipadas Máquinas Césped de CorteUnidad la de Condición la Verifique Continuacin Motor del Arranque Motor del Mínima Marcha de AjusteMotor del Parada Mínima marcha de AjusteCombustible de Mezcla Motor del ArranqueCombustible de Tanque el Llenando De proporción a mezclaSierra tipo cuchilla la Monte EnsamblajeT2510X Disco/Cuchilla T3410X Secundario Protector Ajustes y EnsamblajeCorte de cabezal el Instale T2510/T2510X corte deMango Acelerador del holgura la Ajuste Ajustes y Ensamblaje6SP Ensamblar de Antes EspecificacionesProducto del Descripción 5SPTrabajo de Area del Alerta Esté Seguridad de EtiquetasPíes 4SPEquipado Debidamente Operario El Seguridad de Generales InstruccionesSeguridad de Declaraciones Introducción Contenido2SP OdadoraP

T2510X, 82014 specifications

The Shindaiwa 82014 and T2510X are notable products in the landscape of outdoor power equipment, emblematic of Shindaiwa's commitment to quality and performance. Designed to meet the rigorous demands of professional landscapers and gardeners, these models boast a combination of advanced technology, user-friendly features, and exceptional reliability.

The Shindaiwa 82014 is a powerful, two-stroke, backpack blower. It features a robust engine that delivers an impressive air volume and velocity, making it ideal for clearing leaves, debris, and other materials from large areas quickly and efficiently. The blower’s lightweight design and ergonomic harness distribute weight evenly, reducing fatigue during extended use. Additionally, the 82014 is equipped with an innovative starting system that makes it easy to start with minimal effort, ensuring that users can get to work quickly without the hassle of cumbersome pull cords.

This model also showcases a low-noise engine, making it compliant with stringent noise regulations, which is especially beneficial for urban landscaping tasks. The engine's efficient fuel consumption enhances runtimes, thereby increasing productivity on the job. The powerful airflow can be adjusted with a simple throttle control, providing versatility for various tasks, whether it’s gentle blowing for flower beds or strong gusts for heavy debris.

On the other hand, the T2510X is a high-performance trimmer, known for its smart design and functionality. This model features a professional-grade, 25.4cc engine that ensures robust power while maintaining low emissions and fuel consumption. The T2510X incorporates a rapid load trimmer head, allowing users to reload line quickly without any tools, thus minimizing downtime and enhancing operational efficiency.

The adjustable handle on the T2510X provides comfort and control, allowing users to tackle any trimming task while maintaining a firm and comfortable grip. Furthermore, the machine is equipped with an anti-vibration system, which helps to reduce operator fatigue and improves overall comfort during prolonged usage.

Both models underscore Shindaiwa’s dedication to delivering equipment that not only meets but exceeds the expectations of professionals in the landscaping industry. With cutting-edge features, a focus on operator comfort, and powerful performance, the Shindaiwa 82014 and T2510X are indispensable tools for anyone looking to achieve optimal results in landscape maintenance and management.
Top Page Image Contents