Shindaiwa 82014 manual Using a Blade T2510X, Blade Thrust, Brushcutter Handlebar, Vertical Cuts

Page 12

Using a Blade T2510X

WARNING!

nBefore working with a blade- equipped unit, always inspect and clean the area of objects that could interfere with or damage the blade.

nNever use a blade near sidewalks, fence posts, buildings or other objects that could cause injury or damage.

nNever use a blade for purposes other than those for which it was designed.

nWhenever you strike a hard object with a blade, always stop the brushcutter and carefully inspect the blade for damage. NEVER OPERATE THE BRUSHCUTTER WITH A DAMAGED BLADE!

nA blade-equipped unit must be equipped with a bicycle-type handlebar or barrier bar as well as a harness or shoulder strap.

nAlways make sure the cutting attachment shield is properly installed before operating this unit.

Blade Thrust

‘Blade thrust’ is a sudden sideways or backward motion of the brushcutter. Such motion may occur when the blade jams or catches on an object such as a sapling tree or tree stump. BE CONSTANTLY ALERT FOR BLADE THRUST AND GUARD AGAINST ITS EFFECTS!

Brushcutter Handlebar

A brushcutter handlebar or barrier bar helps prevent the operator from moving forward, or the unit moving rearward, thus preventing inadvertent bodily contact with the blade. ALWAYS KEEP THE HANDLEBAR OR BARRIER BAR SECURELY IN PLACE ON THE UNIT!

Brushcutter Shoulder Strap

A shoulder strap provides additional protection against blade thrust. In addition, a shoulder strap gives significant support and comfort to help ensure safe and efficient operation.

When operating a T2510X with a blade, make sure both the handle and shoulder strap are adjusted to the size of the operator using the unit.

Engine Operating Speeds

Operate the unit at full throttle while cutting. Best fuel efficiency is obtained by releasing the throttle when swinging back after a cut.

nTo prevent possible engine damage, do not allow the brushcutter to run at high speeds without a load.

nAvoid operating the engine at low speeds. Doing so can lead to rapid clutch wear. In addition, slow-speed operation tends to cause grass and debris to wrap around the cutting head.

Using a Blade T2510X

The blade rotates counter-clockwise. For best performance and to minimize being stuck by debris, move the blade from right to left while advancing on your work. Position the blade so cuts are made between the blade’s 7 o’clock and 10 o’clock positions (as viewed from above). DO NOT cut between the

10 o’clock and 5 o’clock positions.

WARNING!

When cutting wood with a blade, feed the blade slowly—never strike or “slam” a spinning blade against the wood.

Vertical Cuts

Hold the brushcutter with the blade at a 90° angle to the ground so the blade’s bottom edge rotates toward the operator. Move the blade from top to bottom through the cut, and cut only with the bottom edge of the blade.

 

O N

 

 

 

 

D

O

C

 

Ten�

 

 

T

 

 

 

U

O’Clock

 

 

 

 

 

 

 

T

Blade�

Rotation

OK To Cut

Seven�

Five��

O’Clock

O’Clock

Figure 26

WARNING!

When making vertical cuts, never allow the blade to exceed waist height.

Figure 27

Cut on the left side of the blade.

KEEP YOUR BODY OUTSIDE THE PATH OF BLADE ROTATION

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents T2510 Trimmer T2510X Trimmer Contents IntroductionSafety Instructions Properly Equipped OperatorSafety Labels Be Aware of the Working EnvironmentSpecifications Prior to AssemblyAir cleaner type Product DescriptionAssembly and Adjustments Adjust Throttle Lever Free PlayHandle Assembly Cutting Attachment ShieldSub-Shield T2510X Trimmer HeadNever operate the T2510X without the safety clip in place Blade T2510X Mount the Saw Blade Mixing Fuel Filling the Fuel Tank Starting the Engine Examples of 501 mixing quantitiesAdjusting Engine Idle When the Engine StartsIdle Speed Adjustment Stopping the EngineChecking Unit Condition Shoulder StrapCutting Grass-Units Equipped with a Trimmer Head Using a Blade T2510X Blade ThrustBrushcutter Handlebar Brushcutter Shoulder StrapGeneral Maintenance Daily MaintenanceHour Maintenance 10/15-Hour Maintenance Remove and replace the filter element139/150-Hour Maintenance Spark Arrester Screen MaintenanceValve Adjustment Long Term Storage Blade SharpeningShindaiwa Tornado Blade Multiple-tooth Circular BladeTroubleshooting Guide Engine does not StartAdditional Problems This Warranty is Administered by Fax 503 81-82-849-2481 Notas POR Administrada ES Garantía Esta 19SPContinuacin Diagnostico Guia 18SPDiagnostico Guia 17SPDiscos de Afilado Plazo Largo de AlmacenamientoMúltiples dientes de Discos Tornado Shindaiwa DiscoGuardachispas Maya la de Mantenimiento Mantenimiento o horas 139/150 CadaHoras 50 Cada Mantenimiento Horas 10/15 Cada MantenimientoFiltro del elemento El reemplace y RetireHoras-10 Cada Mantenimiento Diario MantenimientoGeneral Mantenimiento T2510X Disco un Usando Corte de Cabezal con Equipadas Máquinas Césped de Corte Hombro de CorreaUnidad la de Condición la Verifique Motor del Mínima Marcha de Ajuste Motor del ParadaContinuacin Motor del Arranque Mínima marcha de AjusteMotor del Arranque Combustible de Tanque el LlenandoCombustible de Mezcla De proporción a mezclaEnsamblaje Sierra tipo cuchilla la MonteT2510X Disco/Cuchilla Ajustes y Ensamblaje Corte de cabezal el InstaleT3410X Secundario Protector T2510/T2510X corte deAcelerador del holgura la Ajuste Ajustes y Ensamblaje Mango6SP Especificaciones Producto del DescripciónEnsamblar de Antes 5SPSeguridad de Etiquetas PíesTrabajo de Area del Alerta Esté 4SPEquipado Debidamente Operario El Seguridad de Generales InstruccionesContenido Seguridad de Declaraciones Introducción2SP OdadoraP
Top Page Image Contents