Shindaiwa 82014, T2510X manual Assembly and Adjustments, Handle, Adjust Throttle Lever Free Play

Page 6

Assembly and Adjustments

Handle

Barrier

Handle Bar

Outer

Tube

	4 Socket-head Cap
Figure 5	screws
Figure 5

Handle

Handle Positioning Label

	Outer Tube
	Barrier
4 Socket-head Cap	Bar
4 Socket-head Cap
screws	Figure 5A
	Figure 5A

Handle

1.The handle is attached to the outer tube at the factory and positioned vertically. See Figure 5.

2.Loosen the 4 socket-head cap screws on the handle and rotate the handle 90 degrees. See Figure 5A.

3.Position the handle forward of the Handle Positioning Label at the best position for operator comfort (usually about 10 inches ahead of the throttle housing).

4.Secure the handle by alternately tightening the four socket-head cap screws in a diagonal or “crisscross” fashion.

Assembly and Adjustments

Adjust Throttle Lever Free Play

The throttle lever free play should be approximately 3/16-1/4 inch (4-6 mm). See Figure 6. Make sure that the throttle lever operates smoothly without binding.

If it becomes necessary to adjust the lever free play, follow the procedures and illustrations that follow.

	251043	3/16-1/4 inch (4-6 mm)
		3/16-1/4 inch (4-6 mm)
Figure 6		Throttle Free Play
Figure 6

Figure 7

1.Loosen the air cleaner cover knob and remove the air cleaner cover.

See Figure 7.

2.Loosen the lock nut on the cable adjuster. See Figure 8.

3.Turn the cable adjuster in or out as required to obtain proper free play 3/16-1/4 inch (4-6 mm). See Figure 8.

4.Tighten the locknut.

Cable
Adjuster
Figure 8	Lock Nut

5. Reinstall the air cleaner cover.

Image 6

Contents T2510 Trimmer T2510X Trimmer Contents Introduction Safety Instructions Properly Equipped OperatorSafety Labels Be Aware of the Working EnvironmentAir cleaner type SpecificationsPrior to Assembly Product DescriptionAssembly and Adjustments Adjust Throttle Lever Free PlayHandle Sub-Shield T2510X AssemblyCutting Attachment Shield Trimmer HeadNever operate the T2510X without the safety clip in place Blade T2510X Mount the Saw BladeStarting the Engine Mixing FuelFilling the Fuel Tank Examples of 501 mixing quantitiesIdle Speed Adjustment Adjusting Engine IdleWhen the Engine Starts Stopping the EngineChecking Unit Condition Shoulder StrapCutting Grass-Units Equipped with a Trimmer Head Brushcutter Handlebar Using a Blade T2510XBlade Thrust Brushcutter Shoulder StrapGeneral Maintenance Daily MaintenanceHour Maintenance 10/15-Hour Maintenance Remove and replace the filter element139/150-Hour Maintenance Spark Arrester Screen MaintenanceValve Adjustment Shindaiwa Tornado Blade Long Term StorageBlade Sharpening Multiple-tooth Circular BladeTroubleshooting Guide Engine does not StartAdditional Problems This Warranty is Administered by Fax 503 81-82-849-2481 Notas POR Administrada ES Garantía Esta 19SPContinuacin Diagnostico Guia 18SPDiagnostico Guia 17SPMúltiples dientes de Discos Discos de AfiladoPlazo Largo de Almacenamiento Tornado Shindaiwa DiscoGuardachispas Maya la de Mantenimiento Mantenimiento o horas 139/150 CadaFiltro del elemento Horas 50 Cada MantenimientoHoras 10/15 Cada Mantenimiento El reemplace y RetireHoras-10 Cada Mantenimiento Diario MantenimientoGeneral Mantenimiento T2510X Disco un Usando Corte de Cabezal con Equipadas Máquinas Césped de Corte Hombro de CorreaUnidad la de Condición la Verifique Continuacin Motor del Arranque Motor del Mínima Marcha de AjusteMotor del Parada Mínima marcha de AjusteCombustible de Mezcla Motor del ArranqueCombustible de Tanque el Llenando De proporción a mezclaEnsamblaje Sierra tipo cuchilla la MonteT2510X Disco/Cuchilla T3410X Secundario Protector Ajustes y EnsamblajeCorte de cabezal el Instale T2510/T2510X corte deAcelerador del holgura la Ajuste Ajustes y Ensamblaje Mango6SP Ensamblar de Antes EspecificacionesProducto del Descripción 5SPTrabajo de Area del Alerta Esté Seguridad de EtiquetasPíes 4SPEquipado Debidamente Operario El Seguridad de Generales InstruccionesContenido Seguridad de Declaraciones Introducción2SP OdadoraP