Shindaiwa X7502825900 manual Hour maintenance Remove and replace the fuel filter element

Page 18

Maintenance (continued)

50-hour maintenance

Remove and replace the fuel filter element.

■■Use a hooked wire to extract the fuel filter from inside the fuel tank. Inspect the fuel filter element. If it shows signs of contamination, replace with a genu- ine Shindaiwa replacement fuel filter element.

CAUTION!

Make sure you do not pierce the fuel line with the end of the hooked wire. The line is delicate and can be dam- aged easily.

■■Before reinstalling the new filter ele- ment, inspect the condition of all the fuel system components (fuel pick- up line, fuel return line, tank vent line, tank vent, fuel cap and fuel tank). If damage, splitting or dete- rioration is noted, the unit should be removed from service until it can be inspected or repaired by a Shin- daiwa-trained service technician.

135-Hour Maintenance

Hooked wire

Fuel filter element

■■Combustion chamber should be decarbonized, and the valve clearance should be adjusted. It is highly recommended that this is done by a Shindaiwa-trained service technician.

■■Replace the spark plug annually: Use only the type recommended in the ”Specifications” section or an equivalent resis- tor type spark plug of the correct heat range. Set spark plug electrode gap to 0.6 mm (0.024 in).

IMPORTANT!

The valve clearance should be adjusted. It is highly recommended that this is done by a Shindaiwa-trained service technician.

Valve Adjustment

1.Remove cylinder cover, rocker arm cover, and spark plug. Rotate the crankshaft while observing the piston through the spark plug opening. When the piston is at the top of the compres- sion stroke (TDC), the valves can be adjusted.

CAUTION!

■■Performing a valve adjustment incorrectly may cause hard starting and/or can damage the engine.

■■If you are unfamiliar with this engine or uncomfortable with this procedure, consult with an authorized Shindaiwa servicing dealer.

2.Loosen adjuster locknut so that the 2.5 mm Allen socket head adjust- ment screw can turn freely.

3.Insert 0.10 mm feeler gauge between valve stem tip and rocker arm.

4.Turn adjustment screw (clockwise = tighter, counter-clockwise = looser) until feeler gauge is almost snug.

Back off just enough to allow gauge to slip out with limited resistance.

5.While holding the adjustment screw in place with the Allen driver, tighten the locknut with a wrench.

6.Turn engine over several times, and returnthe to TDC-compression. Recheck with proper feeler gauge to make sure clearance adjust- ment did not change as a result of tightening the locknut. Readjust as necessary.

7.Replace rocker arm cover gasket to assure proper sealing and install cover.

IMPORTANT!

If a new gasket is not available and/ or the old gasket is not damaged, the old gasket may be reused. Never use cracked or damaged gaskets!

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents C254 Brushcutter Contents IntroductionWork Safely SafetySafety Labels Stay AlertProperly Equipped Operator Be Aware of the Working EnvironmentSpecifications Product DescriptionHandlebar Assembly Install the handlebar AssemblyPrior to Assembly Emission Control Exhaust & EvaporativeCutting attachment shield Install trimmer headNylon line replacement To advance trimmer line TipBlade Installation Install Metal ShieldInstall Blade Mixing Fuel Fuel RequirementsFilling the fuel tank After useMinimize the Risk of Fire Starting the Engine Press primer bulbStopping the Engine Checking Unit ConditionOperation Engine Operating Speeds Cutting grass with a trimmer headTrimmer head styles Trimming and Mowing GrassBrushcutter Handlebar Using a bladeBlade Thrust Brushcutter Shoulder StrapMaintenance Remove and clean or replace the spark plug Hour maintenance More frequently in dusty conditions10/15-Hour maintenance Hour maintenance Gearcase lubricationHour maintenance Remove and replace the fuel filter element Hour MaintenanceValve Adjustment Engine Break-In Carburetor AdjustmentMuffler and spark arrester maintenance High Altitude OperationBlade Sharpening Adjusting Engine IdleIdle Speed Adjustment Multiple-tooth Circular BladeLong Term Storage Troubleshooting Guide Possible CauseIs the engine overheating? Symptom Possible Cause Remedy Exceptions Purchased Repair Parts and Accessories 99922201033 Page Page Page Page Servicing Information T10713001001/T10713999999

X7502825900 specifications

The Shindaiwa X7502825900 is a high-performance, cutting-edge machine that excels in both functionality and ease of use. Designed for professional landscapers and horticulturists, this powerful tool stands out for its robust construction and impressive capabilities, making it a reliable asset for any outdoor task.

One of the main features of the X7502825900 is its powerful engine. The equipment is equipped with a two-stroke engine that ensures enhanced efficiency and performance. This engine delivers an impressive power-to-weight ratio, enabling users to tackle heavy-duty tasks with ease while minimizing fatigue during extended use. Additionally, the advanced engine technology helps in reducing emissions, making it environmentally friendly.

The X7502825900 is designed with user comfort in mind. It features an ergonomic handle that provides a comfortable grip and reduces vibrations during operation. This ensures that users can work for longer periods without experiencing discomfort or strain. Furthermore, the machine incorporates a lightweight frame, which enhances maneuverability and allows for precise control in varied working conditions.

Another notable characteristic of the Shindaiwa X7502825900 is its cutting technology. The equipment is equipped with an ultra-efficient cutting head that facilitates clean and precise cuts every time. This feature is particularly beneficial for landscaping tasks, as it ensures a professional finish on hedges, shrubs, and other foliage. The easy-to-replace cutting accessories further enhance its versatility, making it adaptable to various trimming needs.

Additionally, the Shindaiwa X7502825900 incorporates innovative air filtration technology. This system helps to maximize the engine's lifespan by keeping harmful dust and debris at bay. By minimizing wear and tear, users can rely on the machine for prolonged periods, making it a cost-effective investment.

Overall, the Shindaiwa X7502825900 is a remarkable tool that combines power, efficiency, and user comfort. With its advanced technologies and thoughtful design features, this equipment meets the demanding needs of professionals in the landscaping industry. Whether tackling large properties or undertaking intricate gardens, the X7502825900 is engineered to deliver outstanding results, ensuring that users can achieve their landscaping goals with minimal effort.
Top Page Image Contents