Shindaiwa 81188, C3410 manual Stopping the Engine, Adjusting Engine Idle, When the Engine Starts

Page 11

Starting the Engine (continued)

WARNING!

The cutting attachment may rotate when the engine is started!

6.When the engine starts, slowly move the choke lever to the "OPEN" position. See Figure 20. (If the engine stops after the initial start, close the choke and restart.)

Open

WARNING!

Never start the engine from the oper- ating position.

7.Operating the throttle will automatically disengage the fast idle setting.

IMPORTANT!

If the engine fails to start after several at- tempts with the choke in the closed posi- tion, the engine may be flooded

with fuel. If flooding is suspected,

move the choke lever to the open position and repeatedly pull the recoil starter to remove excess fuel and start the engine. If the engine still fails to start, refer to the troubleshooting section of this manual.

When the Engine Starts...

After the engine starts, allow the en- gine to warm up at idle 2 or 3 minutes before operating the unit.

After the engine is warm, pick

up the unit and clip on the shoulder strap. See page 12.

Advancing the throttle makes the cut- ting attachment turn faster; releasing the throttle permits the attachment to stop turning. If the cutting attachment continues to rotate when the engine returns to idle, carburetor idle speed should be adjusted (see "Adjusting Engine Idle" below).

Figure 20

Stopping the Engine

OFF

C3410

Figure 21

Idle the engine briefly before stopping (about 2 minutes), then slide the ignition switch to the “O” (Engine OFF) position.

Adjusting Engine Idle

 

 

 

 

 

 

 

 

 

Idle Adjusting

Figure 22

Screw

 

 

 

 

The engine must return to idle speed whenever the throttle lever is released. Idle speed is adjustable, and must be set low enough to permit the engine clutch to disengage the cutting attachment.

Idle Speed Adjustment

WARNING!

The cutting attachment must NEVER rotate at engine idle! If the idle speed cannot be adjusted by the procedure described here, return the trimmer to your Shindaiwa dealer for inspection.

1.Place the trimmer on the ground, then start the engine, and then allow it to idle 2-3 minutes until warm.

2.If the attachment rotates when the engine is at idle, reduce the idle speed by turning the idle adjustment screw counter-clockwise. See Figure 22.

3.If a tachometer is available, the engine idle speed should be final adjusted to 3,000 (±300) RPM (min-1).

4.Carburetor fuel mixture adjustments are preset at factory and cannot be serviced in the field.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents C3410 C3410 BrushcutterIntroduction ContentsSafety Instructions Always use the proper cutting tool for the job Properly Equipped OperatorBe Aware of the Working Environment Safety LabelsSpecifications C3410 Prior to AssemblyProduct Description Cutting Attachment Shield AssemblyInstall the Cutting Attachment Shield C3410 Outer tube and loosely installAdjust Throttle Lever Free Play AdjustmentsHandle Bar C3410 Install the handlebar Clockwise Installing a Trimmer HeadRemove the hex wrench Installing a BladeExamples of 501 mixing quantities Mixing FuelStarting the Engine Filling the Fuel TankIdle Speed Adjustment Adjusting Engine IdleCutting attachment may rotate when the engine is started When the Engine StartsCutting Grass-Units equipped with a trimmer head Checking Unit ConditionShoulder Strap C3410 Operating Units with a Blade Using a Blade C3410Hour Maintenance General MaintenanceDaily Maintenance Every 10 to 15 hours of operation 10/15-Hour MaintenanceSpark Arrester Screen Maintenance 139/150-Hour MaintenanceMultiple-tooth Circular Blade Long Term StorageBlade Sharpening Shindaiwa Tornado BladeTroubleshooting Guide Additional Problems Emission System Warranty Statement Emisión de Sistema del Garantía de Declaración Por administrada es garantía Esta19SP Continuación Diagnostico GuiaDiagnostico Guia Tornado Shindaiwa Disco Discos de AfiladoPlazo Largo de Almacenamiento Múltiples Dientes de DiscosBalancín Guardachispas Maya la de MantenimientoMantenimiento o horas 139/150 Cada 32 figura la Consulte.motor del tapa la15SP Horas 50 Cada MantenimientoHoras 10/15 Cada Mantenimiento Principal eje del estrias las LubriqueGeneral Mantenimiento Horas 10 Cada MantenimientoDiario Mantenimiento C3410 Disco un Usando Cuchilla una con Unidades OperandoUnidad la de Condición la Verifique Corte de Cabezal con Equipadas Máquinas Césped de CorteMínima Marcha de Ajuste Motor del Mínima Marcha de AjusteMotor del Parada Continuación Motor del ArranqueCombustible de Mezcla CombustibleDe Tanque el Llenando Motor del ArranqueCuchilla la Instalando 8SP Nylon de Cabezal del Instalación7SP Continuación EnsamblajeAcelerador del holgura la Ajuste Ajustes Barra tipo mango el Instale C3410 Mango6SP EnsamblajeEnsamblar de Antes C3410 EspecificacionesProducto del Descripción Trabajo de Area del Alerta Esté Seguridad de Etiquetas3SP Equipado Debidamente Operario El Seguridad de InstruccionesLimpios mangos los mantenga Siempre Cuidado con Trabaje ContenidoAlerta Mantengase Desmalezadora

81188, C3410 specifications

The Shindaiwa C3410,81188 is a powerful and reliable brushcutter that has gained recognition among landscaping professionals and gardening enthusiasts alike. This innovative tool is designed to tackle heavy-duty cutting tasks with ease while ensuring user comfort and efficiency.

One of the standout features of the C3410,81188 is its robust two-stroke engine, which delivers an impressive amount of power relative to its compact size. The engine is engineered for high performance, ensuring that users can cut through dense brush, thick grass, and stubborn weeds without straining the equipment. This power, combined with its lightweight design, allows for extended use without causing fatigue.

The C3410,81188 incorporates advanced starting technologies, making it easier for users to start the machine quickly and effortlessly. The inclusion of an automatic choke feature streamlines the starting process, reducing the need for manual adjustments, and allowing for a smoother operation right from the first pull.

User comfort is a priority with the Shindaiwa C3410,81188. The ergonomic design of the handle provides excellent grip and control, while the anti-vibration system helps minimize fatigue during prolonged use. This is particularly beneficial for professionals who use the machine for hours on end. The adjustable handle also allows for customization to suit various user preferences and body types, enhancing the overall experience.

Moreover, the cutting attachments of the C3410,81188 are versatile and adaptable, enabling users to switch between different heads such as trimmers, blades, and saws. This versatility makes it an ideal tool for various landscaping tasks, from delicate trimming to heavy-duty brush clearing.

In addition to its technical features, the Shindaiwa C3410,81188 is built with durability in mind. Constructed from high-quality materials, the brushcutter is designed to withstand challenging conditions and frequent use. Its maintenance-friendly design further supports longevity, ensuring that users can easily access components for routine checks and servicing.

Overall, the Shindaiwa C3410,81188 is a feature-rich brushcutter that combines power, comfort, and durability. Whether for professional landscapers or avid gardeners, this tool stands out as a reliable solution for maintaining outdoor spaces efficiently and effectively.
Top Page Image Contents