Shindaiwa C3410, 81188 manual 139/150-Hour Maintenance, Spark Arrester Screen Maintenance

Page 16

139/150-Hour Maintenance

Maintenance after first 139-hours, then every 150-hours thereafter.

Combustion chamber should be decar- bonized, and the valve clearance should be adjusted. It is highly recommended that this is done by a Shindaiwa-trained service technician.

Replace the spark plug annually: Use only NGK CMR5H or equivalent resis- tor type spark plug of the correct heat range. Set spark plug electrode gap to 0.024-0.028 inch (0.6 -0.7 mm).

NOTE:

The NGK CMR5H also meets the require- ments for electro magnetic compliance (EMC).

Valve Adjustment

1.Remove cylinder cover, rocker arm cover, and set piston at TDC-compresion.

CAUTION!

Performing a valve adjustment incorrectly may cause hard starting and/or can damage the engine.

If you are unfamiliar with this engine or uncomfortable with this proce- dure, consult with an authorized Shindaiwa servicing dealer.

2.Loosen adjuster locknut so that the 2.5 mm Allen socket head adjustment screw can turn freely.

3.Insert .004" (0.10 mm) feeler gauge for both intake and exhaust between valve stem tip and rocker arm.

4.Turn adjustment screw (clockwise = tighter, counter-clockwise = looser) until feeler gauge is almost snug. Back off just enough to allow gauge to slip out with limited resistance.

5.While holding adjustment screw in place with Allen driver, tighten locknut with wrench.

6.Turn engine over several times, and return to TDC-compression. Recheck with proper feeler gauge to make sure clearance adjustment did not change as a result of tightening locknut. Readjust as necessary.

7.Replace rocker arm cover gasket to as- sure proper sealing and install cover.

IMPORTANT!

If new gasket is not available and/or old gasket is not damaged, old gasket may be reused. Never use cracked or damaged gaskets!

Spark Arrester Screen Maintenance

If the engine becomes sluggish and low on power, check and clean the spark arrester screen.

WARNING!

Never operate the unit with a damage or missing muffler or spark arrester! Operating with a missing or damaged spark arrester is a fire hazard and could also damage your hearing.

1.With a 3 mm hex wrench remove the 3 engine cover screws and the engine cover. See Figure 32.

2.With a 4 mm hex wrench remove the 3 muffler bolts and the muffler. See Figure 32.

3.With a small flat bladed screwdriver remove the 2 screws holding the spark arrester screen and cover to the muffler. See Figure 32.

4.Remove the screen and clean it with a stiff bristle brush.

5.Inspect the cylinder exhaust port for any carbon buildup.

IMPORTANT!

If you note excessive carbon buildup, con- sult with an authorized Shindaiwa servicing dealer.

6.Reassemble the spark arrester, muffler and engine cover in the reverse order of disassembly.

Engine Cover

 

 

Screws

 

 

 

 

Cover

 

 

Muffler

 

Muffler

 

 

Gasket

 

 

 

Muffler

 

 

Bolts

 

 

Spark Arrester

 

 

Screen

 

 

Spark Arrester

341033

Cover

Cover

 

 

 

Figure 32

Screws

 

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents C3410 Brushcutter C3410Safety Instructions ContentsIntroduction Properly Equipped Operator Always use the proper cutting tool for the jobSafety Labels Be Aware of the Working EnvironmentProduct Description Prior to AssemblySpecifications C3410 Assembly Install the Cutting Attachment Shield C3410Outer tube and loosely install Cutting Attachment ShieldHandle Bar C3410 Install the handlebar AdjustmentsAdjust Throttle Lever Free Play Installing a Trimmer Head ClockwiseInstalling a Blade Remove the hex wrenchMixing Fuel Starting the EngineFilling the Fuel Tank Examples of 501 mixing quantitiesAdjusting Engine Idle Cutting attachment may rotate when the engine is startedWhen the Engine Starts Idle Speed AdjustmentShoulder Strap C3410 Checking Unit ConditionCutting Grass-Units equipped with a trimmer head Using a Blade C3410 Operating Units with a BladeDaily Maintenance General MaintenanceHour Maintenance 10/15-Hour Maintenance Every 10 to 15 hours of operation139/150-Hour Maintenance Spark Arrester Screen MaintenanceLong Term Storage Blade SharpeningShindaiwa Tornado Blade Multiple-tooth Circular BladeTroubleshooting Guide Additional Problems Emission System Warranty Statement Por administrada es garantía Esta Emisión de Sistema del Garantía de DeclaraciónContinuación Diagnostico Guia 19SPDiagnostico Guia Discos de Afilado Plazo Largo de AlmacenamientoMúltiples Dientes de Discos Tornado Shindaiwa DiscoGuardachispas Maya la de Mantenimiento Mantenimiento o horas 139/150 Cada32 figura la Consulte.motor del tapa la BalancínHoras 50 Cada Mantenimiento Horas 10/15 Cada MantenimientoPrincipal eje del estrias las Lubrique 15SPDiario Mantenimiento Horas 10 Cada MantenimientoGeneral Mantenimiento Cuchilla una con Unidades Operando C3410 Disco un UsandoCorte de Cabezal con Equipadas Máquinas Césped de Corte Unidad la de Condición la VerifiqueMotor del Mínima Marcha de Ajuste Motor del ParadaContinuación Motor del Arranque Mínima Marcha de AjusteCombustible De Tanque el LlenandoMotor del Arranque Combustible de MezclaCuchilla la Instalando Nylon de Cabezal del Instalación 8SPContinuación Ensamblaje Acelerador del holgura la Ajuste AjustesBarra tipo mango el Instale C3410 Mango 7SPEnsamblaje 6SPProducto del Descripción C3410 EspecificacionesEnsamblar de Antes Seguridad de Etiquetas Trabajo de Area del Alerta EstéLimpios mangos los mantenga Siempre Equipado Debidamente Operario El Seguridad de Instrucciones3SP Alerta Mantengase ContenidoCuidado con Trabaje Desmalezadora

81188, C3410 specifications

The Shindaiwa C3410,81188 is a powerful and reliable brushcutter that has gained recognition among landscaping professionals and gardening enthusiasts alike. This innovative tool is designed to tackle heavy-duty cutting tasks with ease while ensuring user comfort and efficiency.

One of the standout features of the C3410,81188 is its robust two-stroke engine, which delivers an impressive amount of power relative to its compact size. The engine is engineered for high performance, ensuring that users can cut through dense brush, thick grass, and stubborn weeds without straining the equipment. This power, combined with its lightweight design, allows for extended use without causing fatigue.

The C3410,81188 incorporates advanced starting technologies, making it easier for users to start the machine quickly and effortlessly. The inclusion of an automatic choke feature streamlines the starting process, reducing the need for manual adjustments, and allowing for a smoother operation right from the first pull.

User comfort is a priority with the Shindaiwa C3410,81188. The ergonomic design of the handle provides excellent grip and control, while the anti-vibration system helps minimize fatigue during prolonged use. This is particularly beneficial for professionals who use the machine for hours on end. The adjustable handle also allows for customization to suit various user preferences and body types, enhancing the overall experience.

Moreover, the cutting attachments of the C3410,81188 are versatile and adaptable, enabling users to switch between different heads such as trimmers, blades, and saws. This versatility makes it an ideal tool for various landscaping tasks, from delicate trimming to heavy-duty brush clearing.

In addition to its technical features, the Shindaiwa C3410,81188 is built with durability in mind. Constructed from high-quality materials, the brushcutter is designed to withstand challenging conditions and frequent use. Its maintenance-friendly design further supports longevity, ensuring that users can easily access components for routine checks and servicing.

Overall, the Shindaiwa C3410,81188 is a feature-rich brushcutter that combines power, comfort, and durability. Whether for professional landscapers or avid gardeners, this tool stands out as a reliable solution for maintaining outdoor spaces efficiently and effectively.
Top Page Image Contents