Shindaiwa C282, X7502825300 manual Filling the Fuel Tank, Mixing Instructions, After use

Page 10

Handling Fuel

DANGER

Fuel is VERY flammable. Use extreme care when mixing, storing or handling or serious personal injury may result.

•Use an approved fuel container.

•DO NOT smoke near fuel.

•DO NOT allow flames or sparks near fuel.

•Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to equalize.

•NEVER refuel a unit when the engine is HOT or RUNNING!

•DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks outdoors over bare ground.

•DO NOT overfill fuel tank. Wipe up spills immediately.

•Securely tighten fuel tank cap and close fuel container after refueling.

•Inspect for fuel leakage. If fuel leakage is found, do not start or operate unit until leakage is repaired.

•Move at least 3m (10 ft.) from refueling location before starting the engine.

Mixing Instructions

1.Fill an approved fuel container with half of the required amount of gasoline.

2.Add the proper amount of engine oil to gasoline.

3.Close container and shake to mix oil with gaso- line.

4.Add remaining gasoline, close fuel container, and remix.

IMPORTANT!

Spilled fuel is a leading cause of hydrocarbon emissions. Some states may require the use of automatic fuel shut-off containers to reduce fuel spillage.

After use

•DO NOT store a unit with fuel in its tank. Leaks can occur. Return unused fuel to an approved fuel stor- age container.

Storage - Fuel storage laws vary by locality. Contact your local government for the laws affecting your area. As a precaution, store fuel in an approved, airtight container. Store in a well-ventilated, unoccupied build-

ing, away from sparks and flames.

IMPORTANT!

Stored fuel may separate. ALWAYS shake fuel container thoroughly before each use.

Filling the Fuel Tank

WARNING!

Minimize the Risk of Fire

■■NEVER smoke or light fires near the engine.

■■ALWAYS stop the engine and allow it to cool before refueling.

■■ALWAYS Wipe all spilled fuel and move at least 3 meters (10 feet) from the fueling point and source before starting.

■■NEVER place flammable material close to the engine muffler.

■■NEVER operate the engine without the muffler and spark arrester screen in place and in good working condition.

■■FUEL IS HIGHLY FLAMMABLE.

■■ALWAYS store gasoline in a container approved for flammable liquids.

■■ALWAYS inspect the unit for fuel leaks before each use. During each refill, check that no fuel leaks from around the fuel cap and/or fuel tank. If fuel leaks are evident, stop using the unit immediately. Fuel leaks must be repaired before using the unit.

■■ALWAYS move the unit at least 3 meters (10 feet) away from a fuel storage area or other readily flam- mable materials before starting the engine.

1.Place the unit on a flat, level surface.

2.Clear any dirt or other debris from around the fuel filler cap.

3.Remove the fuel cap, and fill the

CAUTION!

Slowly remove the fuel cap only after stopping the engine.

tank with clean, fresh fuel.

4.Reinstall the fuel filler cap and tighten firmly.

5.Wipe away any spilled fuel before starting engine.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents C282 Brushcutter Contents IntroductionWork Safely SafetySafety Labels Stay AlertProperly Equipped Operator Be Aware of the Working EnvironmentSpecifications Product DescriptionHandlebar Assembly Install the handlebar AssemblyPrior to Assembly Emission Control Exhaust & EvaporativeSub-Shield when trimmer head is in use Adjust throttle lever free playCutting Attachment Shield Installing a Trimmer Head Installing Brushcutter BladeMixing Fuel Examples of 501 mixing quantitiesAfter use Filling the Fuel TankMixing Instructions Slowly remove the fuel cap only after stopping the engineStarting the Engine When the Engine StartsNever start the engine from the operating position Operation Stopping the EngineChecking Unit Condition Starting a Flooded EngineEngine Operating Speeds Using a bladeCutting grass with a trimmer head Trimmer head stylesBlade Thrust General maintenanceBrushcutter Handlebar Maintenance Hour maintenance 10/15 hour maintenanceMuffler maintenance Remove and replace the fuel filter elementMultiple-tooth Circular Blade Carburetor AdjustmentBlade Sharpening Engine Break-InIdle Speed Adjustment Adjusting Engine IdleLong Term Storage Troubleshooting Guide Engine is knocking Poor acceleration Engine stops abruptlyExceptions Purchased Repair Parts and Accessories 01/2010 Page Page T10011001001/T10011999999 Servicing InformationT09912001001/T09912999999

X7502825300, C282 specifications

The Shindaiwa C282 is a powerful and versatile brush cutter designed for professional landscapers and homeowners alike. Known for its reliability and performance, the C282 is equipped with features that make it a top choice for tackling tough vegetation with ease.

One of the standout features of the Shindaiwa C282 is its high-performance engine. The unit is powered by a 28.1cc two-stroke engine, which provides excellent power-to-weight ratios. This allows the user to efficiently manage demanding tasks without feeling weighed down. The engine is designed for reduced emissions, making it environmentally friendlier while still delivering robust performance.

The C282 incorporates the unique Shindaiwa Easy Start technology, which significantly reduces the effort needed to start the machine. This feature minimizes the frustration often associated with starting two-stroke engines, allowing users to get to work quickly and efficiently.

Another significant characteristic of the Shindaiwa C282 is its ergonomic design. The brush cutter comes with a comfortable, padded handle and a lightweight frame that enhances maneuverability during operation. The machine's balanced construction ensures less fatigue during extended use, making it easier for operators to tackle large areas of overgrown terrain.

The Shindaiwa C282 also features a durable cutting head, which can be easily replaced to accommodate different cutting needs. The option to use both blades and nylon line allows users to switch between cutting dense underbrush and lighter weeds as needed. This versatility makes the C282 an invaluable tool for any landscaping task.

Durability is another critical aspect of the C282's design. Constructed from high-quality materials, this brush cutter is built to withstand the rigors of professional use, prolonging its lifespan and ensuring consistent performance over time.

Ultimately, the Shindaiwa C282 brush cutter, marked by model number X7502825300, combines powerful technology, ergonomic comfort, and durability, making it a dependable choice for anyone looking to maintain their landscape. Whether you're a seasoned professional or a DIY enthusiast, the C282 provides the capabilities required to handle any brush cutting job efficiently. With its innovative features and robust design, the Shindaiwa C282 stands out in the competitive market of outdoor power equipment, delivering reliability to its users.
Top Page Image Contents