Shindaiwa X7502825300, C282 manual 01/2010

Page 25

ECHO INCORPORATED EMISSION CONTROL WARRANTY STATEMENT

FOR ECHO AND SHINDAIWA BRANDS

The Environmental Protection Agency (EPA) and the California Air Resources Board (C.A.R.B.) and ECHO Incorporated (ECHO Inc.) are pleased to explain the emission control system warranty on your 2010 and later equipment/small off-road engine (SORE). New equipment/SORE must be designed, built and equipped to meet stringent EPA and C.A.R.B. anti-smog standards. ECHO Inc. must warrant the emission control system on your equipment/SORE for the periods of time listed below, provided there has been no abuse, neglect or improper maintenance of your equipment/ SORE. Your emission control system may include parts such as: carburetor, fuel-injection system, ignition system, catalytic converter/muffl er, fuel tank, fuel feed lines, fuel cap assembly, spark plug, air fi lters, and other associated components. Where a warrantable condition exists, ECHO Inc will repair your equipment/SORE at no cost to you including diagnosis, parts and labor. The Emission Control System warranty is extended to the original owner including all subsequent owners.

MANUFACTURER'S WARRANTY COVERAGE:

The emission control system is warranted for 2 years or the length of the ECHO Inc. warranty, whichever is longer. If any emission-related part on your equipment is defective, the part will be repaired or replaced by ECHO Inc. or its Authorized Service Representative.

OWNER'S WARRANTY RESPONSIBILITIES:

As the equipment/SORE owner, you are responsible for the performance of the required maintenance listed in your Operator's Manual. ECHO Inc. recommends that you retain all receipts covering maintenance on your equipment/SORE however, ECHO Inc. cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance. As the equipment/SORE owner, you should be aware that ECHO Inc. may deny you warranty coverage if your equipment/SORE or a part has failed due to abuse, neglect, improper maintenance or unapproved modifi cations.

You are responsible for presenting your equipment/SORE to an ECHO Inc. authorized service representative as soon as a problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. If a warrantable condition exists and there is no Authorized Dealer within 100 miles, ECHO Inc. will pay to ship the unit to the nearest authorized dealer. If you have questions regarding your warranty coverage, you should contact ECHO Inc. at 1-800-673-1558, web site WWW.ECHO-USA.COM or contact Shindaiwa at 1-877-986- 7783, web site WWW.SHINDAIWA.COM.

WHAT DOES THIS WARRANTY COVER?

ECHO Inc. warrants that your equipment/SORE was designed, built and equipped to conform with applicable EPA and C.A.R.B. emissions standards and that your equipment/SORE is free from defects in material and workmanship that would cause it to fail to conform with applicable requirements for 2 years or the length of the ECHO Inc. warranty, whichever is longer. The warranty period begins on the date the product is purchased by an end user.

HOW WILL A COVERED PART BE CORRECTED?

If there is a defect in a part covered by this warranty, any ECHO Inc. Authorized Service Dealer will correct the defect. You will not have to pay anything to have the part adjusted, repaired or replaced. This includes any labor and diagnosis for warranted repairs performed by the dealer. In addition, engine parts not expressly covered under this warranty but whose failure is a result of a failure of a covered part will be warranted.

WHAT PARTS ARE COVERED?

Any applicable emission related part not scheduled for "required maintenance" will be repaired or replaced within the warranty period. The repaired or replaced part will be warranted for the remaining ECHO Inc. warranty period.

Any warranted part that is scheduled only for regular inspection in the written instructions supplied is warranted for the warranty period stated above. Any such part repaired or replaced under warranty will be warranted for the remaining ECHO Inc. warranty period.

Any emission related part scheduled for replacement during "required maintenance" is warranted for the period of time prior to the fi rst scheduled replacement point for that part. Any such part repaired or replaced under warranty shall be warranted for the remainder of the period prior to the fi rst scheduled replacement point for that part.

Any manufacturer-approved replacement part may be used in the performance of any warranty maintenance or repairs on emission related parts, and must be provided without charge if the part is still under warranty.

Any replacement part that is equivalent in performance and durability may be used in non-warranty maintenance or repairs, and shall not reduce the warranty obligations of the manufacturer.

Throughout the equipment/SORE warranty period, ECHO Inc. will maintain a supply of warranted parts suffi cient to meet the expected demand for such parts.

SPECIFIC EMISSION RELATED WARRANTED PARTS:

 

• Electronic Ignition System

• Spark Plug

• Catalytic Converter / Muffl er Assembly

• Carburetor (complete assembly or replaceable components)

• Choke

• Fuel-Injection Assembly (or replaceable components)

• Fuel Tank

• Fuel Cap Assembly

• Air Filter

• Fuel Feed Line (and associated clamps/connectors as applicable)

WHAT IS NOT COVERED?

Any failure caused by abuse, neglect, improper maintenance, unapproved modifi cations, use of unapproved add-on parts/modifi ed parts or unapproved accessories.

This Emission Control Warranty is valid only for the U.S.A., it's Territories, and Canada.

99922201033

 

01/2010

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents C282 Brushcutter Introduction ContentsSafety Labels SafetyWork Safely Stay AlertBe Aware of the Working Environment Properly Equipped OperatorProduct Description SpecificationsPrior to Assembly AssemblyHandlebar Assembly Install the handlebar Emission Control Exhaust & EvaporativeSub-Shield when trimmer head is in use Adjust throttle lever free playCutting Attachment Shield Installing Brushcutter Blade Installing a Trimmer HeadExamples of 501 mixing quantities Mixing FuelMixing Instructions Filling the Fuel TankAfter use Slowly remove the fuel cap only after stopping the engineStarting the Engine When the Engine StartsNever start the engine from the operating position Checking Unit Condition Stopping the EngineOperation Starting a Flooded EngineCutting grass with a trimmer head Using a bladeEngine Operating Speeds Trimmer head stylesBlade Thrust General maintenanceBrushcutter Handlebar Maintenance 10/15 hour maintenance Hour maintenanceRemove and replace the fuel filter element Muffler maintenanceBlade Sharpening Carburetor AdjustmentMultiple-tooth Circular Blade Engine Break-InIdle Speed Adjustment Adjusting Engine IdleLong Term Storage Troubleshooting Guide Engine is knocking Engine stops abruptly Poor accelerationExceptions Purchased Repair Parts and Accessories 01/2010 Page Page T10011001001/T10011999999 Servicing InformationT09912001001/T09912999999

X7502825300, C282 specifications

The Shindaiwa C282 is a powerful and versatile brush cutter designed for professional landscapers and homeowners alike. Known for its reliability and performance, the C282 is equipped with features that make it a top choice for tackling tough vegetation with ease.

One of the standout features of the Shindaiwa C282 is its high-performance engine. The unit is powered by a 28.1cc two-stroke engine, which provides excellent power-to-weight ratios. This allows the user to efficiently manage demanding tasks without feeling weighed down. The engine is designed for reduced emissions, making it environmentally friendlier while still delivering robust performance.

The C282 incorporates the unique Shindaiwa Easy Start technology, which significantly reduces the effort needed to start the machine. This feature minimizes the frustration often associated with starting two-stroke engines, allowing users to get to work quickly and efficiently.

Another significant characteristic of the Shindaiwa C282 is its ergonomic design. The brush cutter comes with a comfortable, padded handle and a lightweight frame that enhances maneuverability during operation. The machine's balanced construction ensures less fatigue during extended use, making it easier for operators to tackle large areas of overgrown terrain.

The Shindaiwa C282 also features a durable cutting head, which can be easily replaced to accommodate different cutting needs. The option to use both blades and nylon line allows users to switch between cutting dense underbrush and lighter weeds as needed. This versatility makes the C282 an invaluable tool for any landscaping task.

Durability is another critical aspect of the C282's design. Constructed from high-quality materials, this brush cutter is built to withstand the rigors of professional use, prolonging its lifespan and ensuring consistent performance over time.

Ultimately, the Shindaiwa C282 brush cutter, marked by model number X7502825300, combines powerful technology, ergonomic comfort, and durability, making it a dependable choice for anyone looking to maintain their landscape. Whether you're a seasoned professional or a DIY enthusiast, the C282 provides the capabilities required to handle any brush cutting job efficiently. With its innovative features and robust design, the Shindaiwa C282 stands out in the competitive market of outdoor power equipment, delivering reliability to its users.
Top Page Image Contents