Shindaiwa X7502825300, C282 manual Adjusting Engine Idle, Long Term Storage, Idle Speed Adjustment

Page 19

Adjusting Engine Idle

Idle Speed Adjustment

 

The engine must return to idle speed

 

1. Place the unit on the ground, then

 

whenever the throttle lever is released.

 

start the engine, and then allow it to

 

Idle speed is adjustable, and must be set

 

idle 2-3 minutes until warm.

 

low enough to permit the engine clutch

 

2. If the attachment rotates when the

 

to disengage the cutting attachment.

 

engine is at idle, reduce the idle

 

 

 

WARNING!

speed by turning the idle adjustment

 

screw counter-clockwise.

 

The cutting attachment

3. If a tachometer is available, adjust

 

must NEVER rotate at engine idle!

idle. Check Specifications page for

 

If the idle speed cannot be adjusted

correct idle speed

 

NOTE:

 

by the procedure described

Idle

here, return the trimmer to your

Carburetor fuel mixture adjustments

adjustment

screw

Shindaiwa dealer for inspection.

are preset at factory and cannot be

Adjusting

 

serviced in the field.

engine idle

 

 

Loading Trimmer Line

1

2

 

 

1.

Cut one piece of line to recommended length.

.080 (2.0 mm) dia. - 20’ (6 m)

 

 

 

2.

Align arrows on top of knob with openings in eyelets.

.095 (2.4 mm) dia. - 14’ (4 m)

 

 

 

3.

Insert one end of trimmer line into an eyelet, and push

.105 (2.7 mm) dia. - 10’ (3 m)

 

 

 

 

 

 

 

 

 

 

 

 

line equal distance through trimmer head.

 

 

 

 

4.

Hold trimmer head while turning knob clockwise to

 

 

 

 

 

wind line onto spool until about 5” (13 cm) of each line

 

 

 

 

 

remains exposed.

 

 

 

 

Trimmer head is now fully loaded and ready for

3

4

 

 

operation.

 

 

 

 

Long Term Storage

IMPORTANT!

Stored fuel ages. Do not mix more fuel than you expect to use in thirty (30) days, ninety (90) days when a fuel stabilizer is added.

Whenever the unit will not be used for 30 days or longer, use the following proce- dures to prepare it for storage:

■■Clean external parts thoroughly. ■■Drain all the fuel from the fuel tank.

■■Remove the remaining fuel from the fuel lines and carburetor.

1.Prime the primer bulb until no more fuel is passing through.

2.Start and run the engine until it stops running.

3.Repeat steps 1 and 2 until the engine will no longer start.

CAUTION!

Gasoline stored in the carbure-

tor for extended periods can cause hard starting, and could also lead to increased service and maintenance costs.

IMPORTANT!

All stored fuels should be stabilized with a fuel stabilizer such as STA-BIL™.

NOTE:

Damage resulting from stale or con- taminated fuel is not covered by the Shindaiwa warranty policy.

■■Remove the spark plug and pour about 1/4 oz. of 2-cycle mixing oil into the cylinder through the spark plug hole. Slowly pull the recoil starter 2 or 3 times so oil will evenly coat the interior of the engine. Rein- stall the spark plug.

■■Before storing the unit, repair or replace any worn or damaged parts.

■■Remove the air cleaner element from the carburetor and clean it thor- oughly with soap and water. Let dry and reassemble the element.

■■Store the unit in a clean, dust-free area.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents C282 Brushcutter Introduction ContentsStay Alert SafetySafety Labels Work SafelyBe Aware of the Working Environment Properly Equipped OperatorProduct Description SpecificationsEmission Control Exhaust & Evaporative AssemblyPrior to Assembly Handlebar Assembly Install the handlebarSub-Shield when trimmer head is in use Adjust throttle lever free playCutting Attachment Shield Installing Brushcutter Blade Installing a Trimmer HeadExamples of 501 mixing quantities Mixing FuelSlowly remove the fuel cap only after stopping the engine Filling the Fuel TankMixing Instructions After useStarting the Engine When the Engine StartsNever start the engine from the operating position Starting a Flooded Engine Stopping the EngineChecking Unit Condition OperationTrimmer head styles Using a bladeCutting grass with a trimmer head Engine Operating SpeedsBlade Thrust General maintenanceBrushcutter Handlebar Maintenance 10/15 hour maintenance Hour maintenanceRemove and replace the fuel filter element Muffler maintenanceEngine Break-In Carburetor AdjustmentBlade Sharpening Multiple-tooth Circular BladeIdle Speed Adjustment Adjusting Engine IdleLong Term Storage Troubleshooting Guide Engine is knocking Engine stops abruptly Poor accelerationExceptions Purchased Repair Parts and Accessories 01/2010 Page Page T10011001001/T10011999999 Servicing InformationT09912001001/T09912999999

X7502825300, C282 specifications

The Shindaiwa C282 is a powerful and versatile brush cutter designed for professional landscapers and homeowners alike. Known for its reliability and performance, the C282 is equipped with features that make it a top choice for tackling tough vegetation with ease.

One of the standout features of the Shindaiwa C282 is its high-performance engine. The unit is powered by a 28.1cc two-stroke engine, which provides excellent power-to-weight ratios. This allows the user to efficiently manage demanding tasks without feeling weighed down. The engine is designed for reduced emissions, making it environmentally friendlier while still delivering robust performance.

The C282 incorporates the unique Shindaiwa Easy Start technology, which significantly reduces the effort needed to start the machine. This feature minimizes the frustration often associated with starting two-stroke engines, allowing users to get to work quickly and efficiently.

Another significant characteristic of the Shindaiwa C282 is its ergonomic design. The brush cutter comes with a comfortable, padded handle and a lightweight frame that enhances maneuverability during operation. The machine's balanced construction ensures less fatigue during extended use, making it easier for operators to tackle large areas of overgrown terrain.

The Shindaiwa C282 also features a durable cutting head, which can be easily replaced to accommodate different cutting needs. The option to use both blades and nylon line allows users to switch between cutting dense underbrush and lighter weeds as needed. This versatility makes the C282 an invaluable tool for any landscaping task.

Durability is another critical aspect of the C282's design. Constructed from high-quality materials, this brush cutter is built to withstand the rigors of professional use, prolonging its lifespan and ensuring consistent performance over time.

Ultimately, the Shindaiwa C282 brush cutter, marked by model number X7502825300, combines powerful technology, ergonomic comfort, and durability, making it a dependable choice for anyone looking to maintain their landscape. Whether you're a seasoned professional or a DIY enthusiast, the C282 provides the capabilities required to handle any brush cutting job efficiently. With its innovative features and robust design, the Shindaiwa C282 stands out in the competitive market of outdoor power equipment, delivering reliability to its users.
Top Page Image Contents