Shindaiwa 81359 manual Using a Blade C242, Operating Units with a Blade

Page 13

Using a Blade C242

WARNING!

nBefore working with a blade- equipped unit, always inspect and clean the area of objects that could interfere with or damage the blade.

nNever use a blade near sidewalks, fence posts, buildings or other objects that could cause injury or damage.

nNever use a blade for purposes other than those for which it was designed.

nWhenever you strike a hard object with a blade, always stop the brushcutter and carefully inspect the blade for damage. NEVER OPERATE THE BRUSHCUTTER WITH A DAMAGED BLADE!

nA blade-equipped unit must be equipped with a bicycle-type handlebar or barrier bar as well as a harness or shoulder strap.

nAlways make sure the cutting at- tachment shield is properly installed before operating this unit.

Blade Thrust

‘Blade thrust’ is a sudden sideways or backward motion of the brushcutter. Such motion may occur when the blade jams or catches on an object such as a sapling tree or tree stump. BE CONSTANTLY ALERT FOR BLADE THRUST AND GUARD AGAINST ITS EFFECTS!

Brushcutter Handlebar

A brushcutter handlebar or barrier bar helps prevent the operator from moving forward, or the unit moving rearward, thus preventing inadvertent bodily contact with the blade. ALWAYS KEEP THE HANDLEBAR OR BARRIER BAR SECURELY IN PLACE ON THE UNIT!

Brushcutter Shoulder Strap

A shoulder strap provides additional protection against blade thrust. In addition, a shoulder strap gives significant support and comfort to help ensure safe and efficient operation.

When operating a C242 with a blade, make sure both the handle and shoulder strap are adjusted to the size of the operator us- ing the unit.

Engine Operating Speeds

Operate the unit at full throttle while cut- ting. Best fuel efficiency is obtained by releasing the throttle when swinging back after a cut.

nTo prevent possible engine damage, do not allow the brushcutter to run at high speeds without a load.

nAvoid operating the engine at low speeds. Doing so can lead to rapid clutch wear. In addition, slow-speed operation tends to cause grass and debris to wrap around the cutting head.

Operating Units with a Blade

The blade rotates counter-clockwise. For best performance and to minimize being stuck by debris, move the blade from right to left while advancing on your work. Position the blade so cuts are made be- tween the blade’s 8 o’clock and 10 o’clock positions (as viewed from above). DO NOT cut between the 10 o’clock and 5 o’clock positions.

WARNING!

When cutting wood with a saw, feed the blade slowly—never strike or “slam” a spinning blade against the wood.

Ten

O'clock

OK To Cut

Eight

O'clock

Figure 24

D

 

O

 

N

 

O

Blade

T

C

Rotation

T

 

U

Five

O'clock

Cut on the left side of the blade. KEEP YOUR BODY OUTSIDE THE PATH

OF BLADE ROTATION

WARNING!

DO NOT use 2-tooth or non-Shindaiwa approved 4-tooth cutting blades with Shindaiwa trimmers and brushcutters.

Vertical Cuts

Hold the brushcutter with the blade at a 90° angle to the ground so the blade’s bottom edge rotates toward the operator. Move the blade from top to bottom through the cut, and cut only with the bottom edge of the blade.

Figure 25

WARNING!

When making vertical cuts, never allow the blade to exceed waist height.

13

Image 13
Contents C242 Brushcutter Safety Instructions ContentsIntroduction Always use the proper cutting tool for the job Properly Equipped OperatorBe Aware of the Working Environment Safety LabelsPrior to Assembly Specifications C242Product Description Cutting Attachment Shield AssemblySub-Shield C242 Handle Bar C242 Install the handlebar AdjustmentsAdjust Throttle Lever Free Play With the gear case output shaft facing Installing a Trimmer HeadBoth holders must be flat against the surface of the blade Installing a BladeFilling the Fuel Tank Mixing FuelStarting the Engine Examples of 501 mixing quantitiesCutting attachment may rotate when the engine is started Adjusting Engine IdleWhen the Engine Starts Idle Speed AdjustmentShoulder Strap C242 Checking Unit ConditionCutting Grass-Units equipped with a trimmer head Operating Units with a Blade Using a Blade C242Daily Maintenance General MaintenanceHour Maintenance Every 10 to 15 hours of operation 10/15-Hour MaintenanceDealer With an authorized Shindaiwa servicingBlade Sharpening Long Term StorageShindaiwa Tornado Blade Multiple-tooth Circular BladeEngine does not Start Troubleshooting GuideAdditional Problems Emission System Warranty Statement Emisión de Sistema del Garantía de Declaración Adicionales Problemas Continuación Diagnostico Guia18SP Diagnostico GuiaPlazo Largo de Almacenamiento Discos de AfiladoMúltiples Dientes de Discos Tornado Shindaiwa DiscoShindaiwa autorizado buidor Mantenimiento horas 135 CadaDistri o servicio de centro su con consulte Carbón, de excesiva acumulación nota SiHoras 10/15 Cada Mantenimiento Horas 50 Cada MantenimientoDiario Mantenimiento Horas 10 Cada MantenimientoGeneral Mantenimiento C242 Disco un Usando Cuchilla una con Unidades OperandoCabezal con Equipadas Máquinas Césped de Corte Corte deUnidad la de Condición la Verifique Mínima Marcha de Ajuste Motor delMotor del Parada Continuación Motor del ArranqueCombustible de Tanque el Llenando Motor del ArranqueCombustible de Mezcla De proporción9SP Cuchilla la InstalandoNylon de Cabezal del Instalación Acelerador del holgura la Ajuste Ajustes Continuación EnsamblajeC242 Mango Allen cabeza EnsamblajeProducto del Descripción C242 EspecificacionesEnsamblar de Antes Píes Seguridad de EtiquetasTrabajo de Area del Alerta Esté Limpios mangos los mantenga Siempre Equipado Debidamente Operario El Seguridad de InstruccionesIncendios de Riesgo El Disminuya ContenidoHumana reproducción la Nocivos efectos otros u congénitos Alerta MantengaseC242 Desmalezadora

81359 specifications

The Shindaiwa 81359 is a powerful and efficient tool designed for landscaping professionals who seek performance and reliability. This multi-purpose piece of equipment excels in various tasks, including trimming, cutting, and clearing, thus providing an essential addition to any outdoor toolkit.

One of the primary features of the Shindaiwa 81359 is its robust engine. Equipped with a high-performance 25.4cc two-stroke engine, the unit delivers ample power to tackle even the most demanding jobs. This engine is designed for efficiency and durability, ensuring that it can withstand the rigors of daily use in professional environments.

The Shindaiwa 81359 also incorporates advanced technologies to enhance operator experience and productivity. The unit features advanced vibration dampening technology, which significantly reduces the amount of vibration transmitted to the user. This results in increased comfort during prolonged use, minimizing fatigue and allowing for more extended periods of operation without compromising performance.

Another notable characteristic of the Shindaiwa 81359 is its lightweight design. Weighing in at just under 10 pounds, the tool is easy to maneuver, making it suitable for various landscaping tasks. The well-balanced design further aids in reducing strain on the operator, making it an ideal choice for residential or commercial landscaping work.

The cutting capabilities of the Shindaiwa 81359 are impressive, with a user-friendly, easy-to-adjust cutting head that allows for quick changes between different trimmer heads or attachments. This versatility equips the operator to seamlessly shift between different tasks, whether edging, trimming, or clearing thick brush.

Moreover, the Shindaiwa 81359 prioritizes environmental consciousness with its low-emission engine design. This aspect is crucial in today’s eco-aware market, where reducing environmental impact is a priority for many professionals and their clients.

In summary, the Shindaiwa 81359 stands out for its powerful 25.4cc engine, advanced vibration dampening, lightweight, ergonomic design, and versatility in cutting options. Ideal for landscaping professionals, its combination of efficiency and user comfort makes it a top choice for tackling a wide range of outdoor tasks.