Shindaiwa 81359 manual Long Term Storage, Blade Sharpening, Shindaiwa Tornado Blade

Page 17

Long Term Storage

Whenever the unit will not be used for 30 days or longer, use the following procedures to prepare it for storage:

nClean external parts thoroughly.

nDrain all the fuel from the fuel tank.

IMPORTANT!

All stored fuels should be stabilized with a fuel stabilizer such as STA-BIL™,

if oil with fuel stabilizer is not used.

CAUTION!

Gasoline stored in the carburetor for extended periods can cause hard starting and could also lead

to increased service and maintenance cost.

nRemove the remaining fuel from the fuel lines and carburetor.

1.Prime the primer bulb until no more fuel is passing through.

2.Start and run the engine until it stops running.

3.Repeat steps 1 and 2 until the engine will no longer start.

nRemove the spark plug and pour about 1/4 ounce of 2-cycle mixing oil into the cylinder through the spark plug hole.

Slowly pull the recoil starter 2 or 3 times so oil will evenly coat the interior of the engine. Reinstall the spark plug.

nBefore storing the unit, repair or replace any worn or damaged parts.

nRemove the air cleaner element from the carburetor and clean it thoroughly with soap and water. Let dry and reassemble the element.

nStore the unit in a clean, dust-free area.

Blade Sharpening

When the cutting edges of the blade be- come dull, they can be resharpened with a few strokes of a file.

In order to keep the blade in balance, all cutting edges must be sharpened equally.

Shindaiwa Tornado™ Blade

To sharpen the cutters on a Shindaiwa Tor- nado Blade, use a 7/32-inch round file. File the leading edge of each tooth to a razor edge. The top plate of each tooth should angle back 30°.

Round

File

30°

Figure 31

WARNING!

Sharpen only the cutting teeth of a blade. DO NOT alter the contour of the blade in any way.

Multiple-tooth Circular Blade

Use a round file to maintain a radius of 0.04 to 0.06" (1 to 1.5 mm) at the base of each tooth. Cutting edges must be offset equally on each side.

Round

File

Figure 32

17

Image 17
Contents C242 Brushcutter Introduction ContentsSafety Instructions Always use the proper cutting tool for the job Properly Equipped OperatorBe Aware of the Working Environment Safety LabelsProduct Description Specifications C242Prior to Assembly Sub-Shield C242 AssemblyCutting Attachment Shield Adjust Throttle Lever Free Play AdjustmentsHandle Bar C242 Install the handlebar With the gear case output shaft facing Installing a Trimmer HeadBoth holders must be flat against the surface of the blade Installing a BladeFilling the Fuel Tank Mixing FuelStarting the Engine Examples of 501 mixing quantitiesCutting attachment may rotate when the engine is started Adjusting Engine IdleWhen the Engine Starts Idle Speed AdjustmentCutting Grass-Units equipped with a trimmer head Checking Unit ConditionShoulder Strap C242 Operating Units with a Blade Using a Blade C242Hour Maintenance General MaintenanceDaily Maintenance Every 10 to 15 hours of operation 10/15-Hour MaintenanceDealer With an authorized Shindaiwa servicingBlade Sharpening Long Term StorageShindaiwa Tornado Blade Multiple-tooth Circular BladeEngine does not Start Troubleshooting GuideAdditional Problems Emission System Warranty Statement Emisión de Sistema del Garantía de Declaración Adicionales Problemas Continuación Diagnostico Guia18SP Diagnostico GuiaPlazo Largo de Almacenamiento Discos de AfiladoMúltiples Dientes de Discos Tornado Shindaiwa DiscoShindaiwa autorizado buidor Mantenimiento horas 135 CadaDistri o servicio de centro su con consulte Carbón, de excesiva acumulación nota SiHoras 10/15 Cada Mantenimiento Horas 50 Cada MantenimientoGeneral Mantenimiento Horas 10 Cada MantenimientoDiario Mantenimiento C242 Disco un Usando Cuchilla una con Unidades OperandoUnidad la de Condición la Verifique Corte deCabezal con Equipadas Máquinas Césped de Corte Mínima Marcha de Ajuste Motor delMotor del Parada Continuación Motor del ArranqueCombustible de Tanque el Llenando Motor del ArranqueCombustible de Mezcla De proporción9SP Cuchilla la InstalandoNylon de Cabezal del Instalación C242 Mango Continuación EnsamblajeAcelerador del holgura la Ajuste Ajustes Allen cabeza EnsamblajeEnsamblar de Antes C242 EspecificacionesProducto del Descripción Trabajo de Area del Alerta Esté Seguridad de EtiquetasPíes Limpios mangos los mantenga Siempre Equipado Debidamente Operario El Seguridad de InstruccionesIncendios de Riesgo El Disminuya ContenidoHumana reproducción la Nocivos efectos otros u congénitos Alerta MantengaseC242 Desmalezadora

81359 specifications

The Shindaiwa 81359 is a powerful and efficient tool designed for landscaping professionals who seek performance and reliability. This multi-purpose piece of equipment excels in various tasks, including trimming, cutting, and clearing, thus providing an essential addition to any outdoor toolkit.

One of the primary features of the Shindaiwa 81359 is its robust engine. Equipped with a high-performance 25.4cc two-stroke engine, the unit delivers ample power to tackle even the most demanding jobs. This engine is designed for efficiency and durability, ensuring that it can withstand the rigors of daily use in professional environments.

The Shindaiwa 81359 also incorporates advanced technologies to enhance operator experience and productivity. The unit features advanced vibration dampening technology, which significantly reduces the amount of vibration transmitted to the user. This results in increased comfort during prolonged use, minimizing fatigue and allowing for more extended periods of operation without compromising performance.

Another notable characteristic of the Shindaiwa 81359 is its lightweight design. Weighing in at just under 10 pounds, the tool is easy to maneuver, making it suitable for various landscaping tasks. The well-balanced design further aids in reducing strain on the operator, making it an ideal choice for residential or commercial landscaping work.

The cutting capabilities of the Shindaiwa 81359 are impressive, with a user-friendly, easy-to-adjust cutting head that allows for quick changes between different trimmer heads or attachments. This versatility equips the operator to seamlessly shift between different tasks, whether edging, trimming, or clearing thick brush.

Moreover, the Shindaiwa 81359 prioritizes environmental consciousness with its low-emission engine design. This aspect is crucial in today’s eco-aware market, where reducing environmental impact is a priority for many professionals and their clients.

In summary, the Shindaiwa 81359 stands out for its powerful 25.4cc engine, advanced vibration dampening, lightweight, ergonomic design, and versatility in cutting options. Ideal for landscaping professionals, its combination of efficiency and user comfort makes it a top choice for tackling a wide range of outdoor tasks.