Servis-Rhino 4211SS manual Attaching Pin on Bucket, Mounting Loader

Page 40

ASSEMBLY

ASSEMBLY

Mounting Loader

Mounting is basically reverse of dismounting.

1.Slowly drive tractor up to loader. Shut off tractor and apply brakes.

2.Connect hydraulic hoses.

3.Start engine and release brakes. Operate loader control lever to extend bucket cylinder, which will rotate bucke down, causing the loader upright to rotate downward into mounting pocket and onto mounting shaft. Operate loader control lever to retract lift cylinders, causing the top of loader upright to rotate rearward into upper mounting saddle. Continue to rotate loader upright into mounting saddle until upright will no longer rotate rearward and front tires of tractor are slightly off the ground.

4.Shut off tractor, apply brakes.

5.Install hitch pins and linch pins, into mounting.

6.Remove linch pins and clevis pins from parking stands, rotate stands into storage position and secure with clevis pins and linch pins (Figure Asm-L-0001).

Attaching Pin on Bucket

Always wear safety glasses when removing or installing buckets.

Always use a drift and hammer made of non-sparking material (a shot-filled mallet is recommended) to install or remove pins. A steel hammer or drift could generate flying metal fragments and result in injury. Always wear safety glasses when using a hammer to remove or install pins.

Material buckets can be installed using tools ordinarily available.

Attach bucket to lift boom frame and bucket cylinders with four 3/8” cap screws and 3/8” lock nuts (supplied with loader).

Attach bucket leveling rod (supplied with loader) through slot in bucket leveling bracket attached to tilt cylinder and inner ear on right side of bucket with 3/16“x 2” cotter pin (5).

4211-4211SS 01/11

Assembly Section 3-6

© 2011 Alamo Group Inc.

Image 40
Contents 4211 4211SS To the Owner/Operator/Dealer Table of Contents Maintenance Section Safety Section Safety General Safety Instructions and Practices4211-4211SS 01/11 Safety Section Operator Safety Instructions and Practices Equipment Operation Safety Instructions and Practices SG-36 Safety Safety 4211-4211SS 01/11 Safety Section SL-33 Safety Safety Transporting Safety Instructions and Practices Maintenance and Service Safety Instructions and Practices 4211-4211SS 01/11 Safety Section See Your Rhino Dealer Storage and Parking Safety Instructions and Practices Concluding Safety Instructions and PracticesDecal Location QTY Level Description Decal Description Loader Positions 4211-4211SS 01/11 Safety Section Loader Safety Safety Federal Laws and Regulations Introduction Section Introduction Introduction Introduction Before Operating this Machine Page Assembly and Connecting the Loader Section Assembly Assembly InstructionsAssembly Proper Rear Ballasting and Wheel Spacing Dismounting Loader and Mounting Loader to Tractor Dismounting LoaderAttaching Pin on Bucket Mounting LoaderMounting and Dismounting Attachment Mounting Attachment to LoaderAssembling Quick Attach Device Installing Quick Attach Device When Connecting an Attachment to the Loader Quick Hitch Assembly Page Operation Section Operation Rhino 4211 & 4211SS LoaderStandard Equipment and Specifications Operator Requirements Operation Personal Protective Equipment PPE Rops and Seat Belt Tractor RequirementsTractor Lighting and SMV Emblem Getting On and Off the Tractor Tractor BallastBoarding the Tractor Dismounting the TractorStarting the Tractor Pre-Operation Inspection and Service Tractor Pre-Operation Inspection/Service Loader Pre-Operation Inspection and ServiceMount Assembly OPS-L-0007B Do not Operate an Unsafe Tractor or Front END Loader Front END Loader PRE-OPERATION Inspection Driving the Tractor and Loader Operating the Tractor and Loader Driving the Tractor and LoaderSG-36 Operation Operation SL-33 Operation Operating the Loader Filling the BucketOperation Lifting the Load Carrying the Load Dumping the Bucket Lowering the BucketOperating with Float Control Loading from a Bank Operation Peeling and Scraping Loading LOW Trucks or Spreaders from a Pile Backfilling Operation Handling Large Heavy Objects Operating Bale Spear Transporting the Tractor and Implement Loader StorageShutting Down the Implement Operation Transporting on Public Roadways Operation Hauling the Tractor and Implement Troubleshooting Guide Page Maintenance Section Maintenance 4211-4211SS 01/11 Maintenance Section Lubrication Schedule Daily Maintenance Cylinder Service Lift and Bucket Cylinder DisassemblyLift and Bucket Cylinder Reassembly StorageStore loader with attachment securely attached Proper Torque for Fasteners Maintenance Maintenance Rhino To the OWNER/OPERATOR/DEALER 4211/4211SS