North Star MTBSL owner manual Connected to the battery

Page 16

	Assembly (continued)
1. Preparatory safety	Preparatory safety steps:
	• ALWAYS use eye protection
	• NEVER smoke or work near sparks or other sources of ignition.
	• NEVER touch both battery terminals at the same time or with any non-
	insulated tools.
	• If battery acid contacts skin or clothing, flush immediately with water and
	neutralize with baking soda.
2. Connect remote	Connect the sprayer’s remote switch to the vehicle battery using the
switch to battery	following procedure:
	a) Disconnect the vehicle battery ground wire.
	b) Connect the remote switch’s red battery clamp to the positive(+) terminal
	of the battery.
	c) Connect the remote switch’s black battery clamp to the negative(-)terminal
	of the battery.
	d) Reconnect the vehicle battery ground wire.
	WARNING: Always connect in this sequence to avoid possible shock.
3. Connect remote	Connect the remote switch to the pump power cord:
switch to pump	Note: Make sure the power switch is in the OFF position on the remote switch.
power cord	Remote switch
	Remote switch
	Pump power cord

4. Verify connection

Verify a complete connection has been made by checking with a DC voltmeter, or by briefly turning the remote switch to the ON position and listening for pump activation.

5.	Attach remote switch	Using supplied velcro pad, affix remote switch to vehicle in a position that is
	to vehicle	easily reached from the driver’s seat.

6.	Disconnect after use	AFTER EACH USE, disconnect power to the sprayer by disconnecting the
		sprayer’s pump cord from the remote switch – the remote switch may remain
		connected to the battery.
		NOTE: It is important to disconnect power to the sprayer when not in use for
		safety reasons. ALWAYS verify that the power has been disconnected or the
		remote switch is in the OFF position before adding chemicals or servicing.

16

Image 16

Contents Mtbsl Hazard Signal Word Definitions Table of Contents Intended Use Spraying PesticidesSummary of Important Safety Information During AssemblyGeneral Chemical Safety Chemical Application SafetyChemical accident procedures Towing SafetyDifferently with filled sprayer attached Closely inspect all contents in the shipping carton UnpackingUnpacking the Manual Bag Following items are found in the manual bagAssembly Step One Attach the tongue to the cart baseStep Two Attach the hitch mount to the tongue Step Three Attach the cart base to the sprayerStep Four Attach wheels to cart base Step Five Attach boom supports and boom bracket to cart baseStep Six Attach boom arms to the boom bracket Step Seven Attach gun hose to spray gun and pump Step Eight Attach hose guide to tankStep Nine Attach gun clips to tank Step Ten Attach drain cap to tankStep Eleven Install boom valve to pump Step Twelve Connect boom valve to boom nozzlesStep Fourteen Connect remote switch to vehicle battery Step Thirteen Attach sprayer to vehicleConnected to the battery Step Fifteen Check and test completed assembly Check and test completed assemblyCheck assembly Working conditionMachine Components Operation Important Safety Information General Chemical SafetyChemical Application Safety Before SprayingDuring Spraying After SprayingTowing Safety Inhalation Operation Preparing the Sprayer for Each Use Important safety rulesInspect Inspect and test the sprayer thoroughly Repair Step One Assess wind conditions and clear work area Operation Using the SprayerSpray because the wind is too strong Step Two Fill the sprayer Fill the sprayer using the following stepsEnsure tank is flushed of all chemicals from prior uses Check drain Fill tankStep Three Operate the sprayer Review safetyBegin agitation if Squeeze trigger & To spray, squeeze the gun trigger Adjust nozzleUnfold one or both boom arms as required Ensure correct spray pattern Ensure uniform coverageStep Four Clean sprayer and decontaminate after use Drain tankDecontaminate LaunderStorage Preparing for storageRemoving from storage Add antifreezeTroubleshooting Before attempting to service the sprayerSpecifications Any Questions, Comments, Problems or Parts OrdersExploded View 28517/28518 Rev. L Part# Description Model QtyAppendix a Broadcast Spray Calibration Tables Approximate flow from one nozzleSpray Pressure Height