North Star MTBSL owner manual Specifications, Any Questions, Comments, Problems or Parts Orders

Page 33

Specifications

Electrical System Requirements
Electrical connection……………….	12 VDC
Amp draw from pump……………...	7.0 Amps
Sprayer Specifications
Maximum GPM…………………….	1.8 GPM
Continuous Pressure………………..	60 PSI
Tank Maximum Capacity…………..	16 Gallons (Item #28517)
Overall Dimensions	26 Gallons (Item #28518)
Overall Dimensions
Item #28517.……………………	34.0”L x 14.5”W x 20.5”H
Item #28518………………….…	34.0”L x 14.5”W x 24.5”H
Dry Weight / Weight full of water
Item #28517…………………….	60 lb. / 188 lb.
Item #28518………………….…	65 lb. / 273 lb.
Broadcast Nozzle Specifications
Overall Spray Width	120 in.
Recommended Overlap	40 in.

Component Materials*
Tank............................…	Polyethylene, EPDM
Suction Tube...............…	Polypropylene, PVC, Stainless Steel
Hose............................…	PVC
Pump...........................…	Polypropylene, Viton, Sanoprene
Valves.........................…	PVC, Buna-N
Gun and Nozzle..........…	Nylon, Polyacetal

*Before using any chemical, check to ensure the chemical is compatible with all materials in the system.

The manufacturer reserves the right to make improvements in design and/or changes in specifications at any time without incurring any obligation to install them on units previously sold.

Any Questions, Comments, Problems or Parts Orders

Call NorthStar Customer Service 1-800-270-0810

33

Image 33

Contents Mtbsl Hazard Signal Word Definitions Table of Contents Spraying Pesticides Intended UseDuring Assembly Summary of Important Safety InformationGeneral Chemical Safety Chemical Application SafetyTowing Safety Chemical accident proceduresDifferently with filled sprayer attached Unpacking Closely inspect all contents in the shipping cartonFollowing items are found in the manual bag Unpacking the Manual BagStep One Attach the tongue to the cart base AssemblyStep Two Attach the hitch mount to the tongue Step Three Attach the cart base to the sprayerStep Five Attach boom supports and boom bracket to cart base Step Four Attach wheels to cart baseStep Six Attach boom arms to the boom bracket Step Eight Attach hose guide to tank Step Seven Attach gun hose to spray gun and pumpStep Nine Attach gun clips to tank Step Ten Attach drain cap to tankStep Twelve Connect boom valve to boom nozzles Step Eleven Install boom valve to pumpStep Thirteen Attach sprayer to vehicle Step Fourteen Connect remote switch to vehicle batteryConnected to the battery Check and test completed assembly Step Fifteen Check and test completed assemblyCheck assembly Working conditionMachine Components General Chemical Safety Operation Important Safety InformationBefore Spraying Chemical Application SafetyDuring Spraying After SprayingTowing Safety Inhalation Important safety rules Operation Preparing the Sprayer for Each UseInspect Inspect and test the sprayer thoroughly Repair Operation Using the Sprayer Step One Assess wind conditions and clear work areaSpray because the wind is too strong Fill the sprayer using the following steps Step Two Fill the sprayerEnsure tank is flushed of all chemicals from prior uses Fill tank Check drainReview safety Step Three Operate the sprayerBegin agitation if Adjust nozzle Squeeze trigger & To spray, squeeze the gun triggerUnfold one or both boom arms as required Ensure uniform coverage Ensure correct spray patternDrain tank Step Four Clean sprayer and decontaminate after useDecontaminate LaunderPreparing for storage StorageRemoving from storage Add antifreezeBefore attempting to service the sprayer TroubleshootingAny Questions, Comments, Problems or Parts Orders SpecificationsPart# Description Model Qty Exploded View 28517/28518 Rev. LApproximate flow from one nozzle Appendix a Broadcast Spray Calibration TablesSpray Pressure Height