MTD Complete Guide on Sharpening Chipper and Shredder Blades
Page 11

Sharpening Or Replacing The Shredder Blade

WARNING: The impeller’s chipper blades are sharp. Wear leather work gloves to protect your hands.

•Stop the engine and make certain that all moving parts have come to a complete stop.

•Disconnect the spark plug wire and ground against the engine.

•Lower the hopper assembly and block up the housing.

•Remove the six hex lock nuts and flat washers from the weld studs on the flail housing. Retain the hardware.

•Carefully separate the hopper assembly from the impeller assembly and remove the support plate.

NOTE: When reassembling the support plate, make certain the embossed tab faces inward towards the impeller.

•Remove the two wing knobs and cupped washers that secure the discharge chute and raise the chute.

•Insert a 1/2” or 3/4” diameter pipe through the flail screen into the impeller to keep it from turning or remove the flail screen and insert a piece of wood into the chute opening.

•Remove the two internal hex screws which secure the shredder blade to the impeller. See Figure 11.

Discharge Chute

Shredder

 

Blade

Weld Stud

 

Internal

 

Hex Screw

 

Hex Bolt,

 

Lock Washer &

 

Flat Washer

 

Impeller

 

Figure 11

NOTE: Use a 3/16” hex key (Allen) wrench on the outside of the shredder blade and a 1/2” box (or socket) wrench on the inside of the shredder blade. Hold the Allen wrench stationary and rotate the box (or socket) wrench to loosen the nut.

•Remove the hex bolt, lock washer and flat washer to completely free the shredder blade.

NOTE: Use caution when removing the blade to avoid contacting the weld studs on the housing.

IMPORTANT: When sharpening the blade, follow the original angle of grind as a guide. It is extremely important that each cutting edge receives an equal amount of grinding to prevent an unbalanced blade. An unbalanced blade will cause excessive vibration when rotating at high speeds and may cause damage to the unit. The blade can be tested by balancing it on a screwdriver or nail. Remove metal from the heavy side until it is balanced evenly.

IMPORTANT: When reassembling the blade, tighten center bolt to between 550 and 700 in.-lbs. and the two outer bolts to between 250 and 350 in.-lbs.

Storing Your Chipper Shredder

•Clean the equipment thoroughly.

•Wipe equipment with an oiled rag to prevent rust.

•Refer to engine manual for correct engine storage instructions.

•Store unit in a clean, dry area. Do not store next to corrosive materials such as fertilizer.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents OPERATOR’S Manual Calling Customer Support Table of ContentsFinding Model Number Engine InformationPreparation Important Safe Operation PracticesTraining Operation Maintenance and StorageLoose Parts In Carton See Figure Disconnecting Spark Plug WireAssembling Your Chipper Shredder Removing Unit From CartonFrame. Loosen but do not remove the bolts Attaching The Discharge Chute All ModelsAttaching The Chipper Chute Attaching The Bag All Models Know Your Chipper ShredderOperating Your Chipper Shredder Lubrication Using The Chipper ShredderMaintenance Customer ResponsibilitiesAll Models Removing The Flail ScreenModels 462 or Storing Your Chipper Shredder Sharpening Or Replacing The Shredder BladeProblem Cause Remedy TroubleshootingTWO Year Limited Warranty Page Part RÉF Pièce Description Page Page Page VENTE-APRÈS Service ET Garantie Sous Pièces Turbine la dans Objet Solution Possibles Causes ProblèmeSaison hors Remisage Niveau au moteur à d’huile niveau le Maintenez Lames des remplacement ou AiguisageEntretien Client du Responsibilités LubricationDéchiqueteuse/broyeuse la de Utilisation ’essence et d’huile Pleins BROYEUSE-DÉCHIQUETEUSE LA DE Utilisation 4 ChapitreDéchiquetage Sac du InstallationBougie la de fil du Débranchement ’éjection goulotte la de InstallationTrémie la de Installation Remisage ET Entretien Utilisation Sécurité DE Consignes 1 Chapitre FormationChapitre VENTE-APRÈS ServiceMoteur DU Renseignement Matières DES Table’UTILISATION Notice

465 specifications

The MTD 465 is a remarkable addition to the world of agricultural tractors, engineered for versatility, efficiency, and user-friendliness. Designed primarily for mid-sized farming operations, the MTD 465 combines power with innovative technology to support a wide range of farming tasks.

One of the main features of the MTD 465 is its robust engine. Powered by a reliable, high-torque diesel engine, this tractor offers outstanding performance, providing farmers with the strength needed for heavier tasks like plowing and towing. Its 65 horsepower capacity strikes a balance between power and fuel efficiency, allowing for extended work periods without frequent refueling stops.

The MTD 465 incorporates advanced hydraulic systems, enhancing its productivity and ease of use. With a high-capacity hydraulic pump, the tractor ensures that attachments and implements operate smoothly and efficiently. Farmers can easily switch between tasks, such as tilling, cultivating, and hauling, thanks to the responsive hydraulic controls.

Another noteworthy technology included in the MTD 465 is the intuitive transmission system. Equipped with a range of gear options, including both manual and automatic settings, it allows for seamless gear changes, enhancing maneuverability in the field. This system is designed to provide optimal torque at various speeds, making it suitable for both slow precision work and faster tasks.

The tractor's ergonomic design contributes to operator comfort during long hours in the fields. With an adjustable seat, easy-to-reach controls, and excellent visibility from the cab, farmers can work efficiently while reducing fatigue. Additionally, the MTD 465 features enhanced safety measures, including protective structures and advanced lighting systems, ensuring safe operation in various conditions.

Maintenance is simplified with the MTD 465, thanks to accessible components and user-friendly service intervals. Farmers can perform routine checks and minor repairs with ease, ensuring that the tractor remains in peak operating condition without excessive downtime.

In conclusion, the MTD 465 tractor stands out for its powerful performance, innovative technologies, and user-centered design. With its versatility and durability, it proves to be an invaluable asset for farmers looking to maximize productivity and efficiency in their agricultural operations. Whether handling heavy-duty tasks or intricate farming activities, the MTD 465 is a reliable partner in modern farming.
Top Page Image Contents