MTD 465 manual Operation, Maintenance and Storage

Page 4

OPERATION

1.Do not put hands and feet near rotating parts or in the feeding chambers and discharge opening. Contact with the rotating impeller can amputate fingers, hands, and feet.

2.Before starting the machine, make sure the chipper chute, feed intake, and cutting chamber are empty and free of all debris.

3.Thoroughly inspect all material to be shredded and remove any metal, rocks, bottles, cans, or other foreign objects which could cause personal injury or damage to the machine.

4.If it becomes necessary to push material through the shredder hopper, use a small diameter stick. Do not use your hands or feet.

5.If the impeller strikes a foreign object or if your machine should start making an unusual noise or vibration, immediately shut the engine off. Allow the impeller to come to a complete stop. Disconnect the spark plug wire, ground it against the engine and perform the following steps:

a.Inspect for damage.

b.Repair or replace any damaged parts.

c.Check for any loose parts and tighten to assure continued safe operation.

6.Do not allow an accumulation of processed material to build up in the discharge area. This can prevent proper discharge and result in kickback of material through the feed opening.

7.Do not attempt to shred or chip material larger than specified on the machine or in this manual. Personal injury or machine damage could result.

8.Never attempt to unclog either the feed intake or discharge opening while the engine is running. Shut the engine off, wait until all moving parts have stopped, disconnect the spark plug wire and ground it against the engine before clearing debris.

9.Never operate without the shredder hopper, chipper chute, or discharge chute properly attached to the machine. Never empty or change discharge bag while the engine is running.

10.Keep all guards, deflectors and safety devices in place and operating properly.

11.Keep your face and body back and to the side of the chipper chute while feeding material into the machine to avoid accidental kickback injuries.

12.Never operate this machine without good visibility or light.

13.Do not operate this machine on a paved, gravel or non-level surface.

14.Do not operate this machine while under the influence of alcohol or drugs.

15.Muffler and engine become hot and can cause a burn. Do not touch.

16.Never pick up or carry machine while the engine is running.

MAINTENANCE AND STORAGE

1.Never tamper with safety devices. Check their proper operation regularly.

2.Check bolts and screws for proper tightness at frequent intervals to keep the machine in safe working condition. Also, visually inspect machine for any damage and repair, if needed.

3.Before cleaning, repairing, or inspecting, stop the engine and make certain the impeller and all moving parts have stopped. Disconnect the spark plug wire and ground it against the engine to prevent unintended starting.

4.Do not change the engine governor settings or overspeed the engine. The governor controls the maximum safe operating speed of the engine.

5.Maintain or replace safety and instruction labels, as necessary.

6.Follow this manual for safe loading, unloading, transporting, and storage of this machine.

7.Never store the machine or fuel container inside where there is an open flame, spark or pilot light such as a water heater, furnace, clothes dryer, etc.

8.Always refer to the operator’s manual for proper instructions on off-season storage.

9.If the fuel tank has to be drained, do this outdoors.

10.Observe proper disposal laws and regulations for gas, oil, etc. to protect the environment.

WARNING: - YOUR RESPONSIBILITY: Restrict the use of this power machine to persons who read, understand and follow the warnings and instructions in this manual and on the machine.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents OPERATOR’S Manual Table of Contents Finding Model NumberEngine Information Calling Customer SupportTraining Important Safe Operation PracticesPreparation Maintenance and Storage OperationDisconnecting Spark Plug Wire Assembling Your Chipper ShredderRemoving Unit From Carton Loose Parts In Carton See FigureAttaching The Chipper Chute Attaching The Discharge Chute All ModelsFrame. Loosen but do not remove the bolts Know Your Chipper Shredder Attaching The Bag All ModelsOperating Your Chipper Shredder Using The Chipper Shredder MaintenanceCustomer Responsibilities LubricationModels 462 or Removing The Flail ScreenAll Models Sharpening Or Replacing The Shredder Blade Storing Your Chipper ShredderTroubleshooting Problem Cause RemedyTWO Year Limited Warranty Page Part RÉF Pièce Description Page Page Page VENTE-APRÈS Service ET Garantie Sous Pièces Solution Possibles Causes Problème Turbine la dans ObjetSaison hors Remisage Entretien Lames des remplacement ou AiguisageNiveau au moteur à d’huile niveau le Maintenez Lubrication Client du ResponsibilitésDéchiqueteuse/broyeuse la de Utilisation BROYEUSE-DÉCHIQUETEUSE LA DE Utilisation 4 Chapitre ’essence et d’huile PleinsSac du Installation DéchiquetageTrémie la de Installation ’éjection goulotte la de InstallationBougie la de fil du Débranchement Remisage ET Entretien Utilisation Formation Sécurité DE Consignes 1 ChapitreVENTE-APRÈS Service Moteur DU RenseignementMatières DES Table Chapitre’UTILISATION Notice

465 specifications

The MTD 465 is a remarkable addition to the world of agricultural tractors, engineered for versatility, efficiency, and user-friendliness. Designed primarily for mid-sized farming operations, the MTD 465 combines power with innovative technology to support a wide range of farming tasks.

One of the main features of the MTD 465 is its robust engine. Powered by a reliable, high-torque diesel engine, this tractor offers outstanding performance, providing farmers with the strength needed for heavier tasks like plowing and towing. Its 65 horsepower capacity strikes a balance between power and fuel efficiency, allowing for extended work periods without frequent refueling stops.

The MTD 465 incorporates advanced hydraulic systems, enhancing its productivity and ease of use. With a high-capacity hydraulic pump, the tractor ensures that attachments and implements operate smoothly and efficiently. Farmers can easily switch between tasks, such as tilling, cultivating, and hauling, thanks to the responsive hydraulic controls.

Another noteworthy technology included in the MTD 465 is the intuitive transmission system. Equipped with a range of gear options, including both manual and automatic settings, it allows for seamless gear changes, enhancing maneuverability in the field. This system is designed to provide optimal torque at various speeds, making it suitable for both slow precision work and faster tasks.

The tractor's ergonomic design contributes to operator comfort during long hours in the fields. With an adjustable seat, easy-to-reach controls, and excellent visibility from the cab, farmers can work efficiently while reducing fatigue. Additionally, the MTD 465 features enhanced safety measures, including protective structures and advanced lighting systems, ensuring safe operation in various conditions.

Maintenance is simplified with the MTD 465, thanks to accessible components and user-friendly service intervals. Farmers can perform routine checks and minor repairs with ease, ensuring that the tractor remains in peak operating condition without excessive downtime.

In conclusion, the MTD 465 tractor stands out for its powerful performance, innovative technologies, and user-centered design. With its versatility and durability, it proves to be an invaluable asset for farmers looking to maximize productivity and efficiency in their agricultural operations. Whether handling heavy-duty tasks or intricate farming activities, the MTD 465 is a reliable partner in modern farming.
Top Page Image Contents