Land Pride RC5020 Plate Disassembly, Type B Clutches Clutch Run-In, Step, Refer to -8 View a

Page 29

Land Pride

Table of Contents

Section 5: Maintenance & Lubrication

Type B Clutches

Clutch Run-In

Refer to Figure 5-8 (View - A):

1.Using a pencil or other marker, scribe a line across the exposed edges of the clutch plates and friction disks.

2.Tighten all 4 nuts uniformly until spring load is low enough that the clutch slips freely with PTO engaged.

23696

Type B Clutch Run-In

Figure 5-8

3.Make sure the area is clear of all bystanders and machine is safe to operate.

4.Start tractor and engage PTO for 2-3 seconds to permit slippage of clutch surfaces. Disengage PTO, then re-engage a second time for 2-3 seconds. Disengage PTO, shut off tractor and remove key. Wait for all components to stop before dismounting from tractor.

5.Inspect clutch and ensure that the scribed markings made on the clutch plates have changed position. Slippage has not occurred if any two marks on the friction disk and plate are still aligned. A clutch that has not slipped must be disassembled to separate the friction disk plates. See “Clutch Disassembly, Inspection & Assembly” below.

Refer to Figure 5-8 (View - B):

6.If no two marks on the friction disk and plate are still aligned, Turn all 4 nuts fully back.

7.Allow clutch to cool to ambient temperature before operating again. Clutch is now ready for use.

8.The clutch should be checked during the first hour of cutting and periodically each week. An additional set of scribe marks can be added to check for slippage.

Clutch Disassembly, Inspection & Assembly

If clutch run-in procedure above indicated that one or more of the friction disks did not slip, then the clutch must be disassembled to separate the friction disks.

NOTE: Before proceeding, secure clutch firmly in a vise or other clamping device to prevent injury.

4-Plate Disassembly

Step 1

If included, remove end half clamps.

Step 2

Tighten the four hex nuts uniformly until the clutch pack and hub are loose.

Step 3

Bend all four retaining lugs out on edge of clutch housing.

Step 4

Remove thrust plate with Belleville Springs and lug rings to access friction discs and hub for inspection or service.

Step 5

Inspect friction discs and hub.

23553

2/02/09

RC5020 (540 RPM) and RCM5020 (1000 RPM) Rotary Cutters 318-474M

27

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Rotary Cutters Table of Contents Safety at All Times Use Safety Lights and Devices Important Safety InformationUse a Safety Chain Practice Safe MaintenancePrepare for Emergencies Tire SafetyWear Protective Equipment Avoid High Pressure Fluids Hazard818-130C 818-240C 818-045C818-552C 818-540C 818-543C 818-561C 818-276C818-840C 818-830C 818-564C 838-094C 838-588C 818-556C818-230C 818-229CIntroduction Using This ManualApplication Owner Assistance Assembly and Set-up Pre-Assembly ChecklistTractor Requirements Before You StartWing Axle Assembly Hitch AssemblyHitch Types Standard Clevis HitchTractor Hook-up Driveline InstallationRefer to -4 on Hydraulic Hook-upCheck Driveline Length Refer to -6 on Unhooking From the CutterRefer to -1& -2 on Refer to -2 onAdjustments Cutting Height AdjustmentCenter and Wing Section Leveling Refer to -1 & FigureOperating Checklist Pre-Start ChecklistInspection Procedures Operating InstructionsRefer to -1& Figure Transport LocksTransporting Operating Speed Field Set-upWing Operating Angle Refer to -1& -2onGeneral Operating Instructions Driveline Turning AngleTable of Contents Shredder Blade Accessory Safety Guard OptionsBaffle Accessory Wheel OptionsHitch Options Hydraulic AccessoriesIndependently Controlled Deck Wings Duplex outletsTractor Maintenance General Maintenance InformationCutter Blade Maintenance Maintenance & LubricationLand Pride Cutter Blade Parts Drivelines With Slip ClutchesRefer to -7 & Table Below Clutch Disassembly, Inspection & AssemblyType a Clutches Clutch Run-In Type B Clutches Clutch Run-In Plate DisassemblyStep Refer to -8 View aSkid Shoe Maintenance Plate AssemblyLand Pride Skid Shoe Replacement Parts Center Skid ShoeLand Pride Touch-up Paint StorageWing Skid Shoe Lubrication Points Adjustable TurnbuckleHrs Axle Hub BearingDivider Box GearboxConventional Driveline Joints & Shields Intermediate Driveline JointsConventional Driveline Profile Tubes Constant Velocity Driveline Joints & Shields Constant Velocity Driveline Profile TubesType of Lubrication Multi-purpose Grease Quantity = Coat GenerouslyWing Driveline Joints & Shields Wing Driveline Profile TubesRC5020 & RCM5020 Specifications & CapacitiesRC5020 and RCM5020 Series At 2 Cutting Height RC5020 and RCM5020 Rotary Cutter Features and BenefitsFeatures Benefits Hinged wing sections Features and Benefits Of Optional EquipmentTroubleshooting Torque Values Chart Tire Inflation ChartAppendix Tire Size InflationGearbox WarrantyCorporate Office P.O. Box 5060 Salina, Kansas 67402-5060 USA
Related manuals
Manual 162 pages 51.6 Kb

RC5020, RCM5020 specifications

The Land Pride RC5020 is a robust rotary cutter designed for agricultural and commercial applications, addressing the need for efficient vegetation management and land maintenance. This machine stands out in its class due to its exceptional durability and innovative features tailored for performance and reliability.

One of the key characteristics of the RC5020 is its heavy-duty construction. Built with a 10-gauge steel deck, it provides exceptional strength and longevity, capable of handling tough cutting conditions. The reinforced blade mounting system ensures maximum blade support, while the ΒΌ-inch thick side skirts add a layer of protection against debris and wear. This rugged structure enables users to tackle dense grass, brush, and other challenging vegetation without compromising performance.

The RC5020 is equipped with a powerful drive system that employs a smooth-running gearbox, ensuring efficient power transmission from the tractor to the cutter. This technology allows for a consistent performance and superior cutting ability, reducing downtime and maintenance needs. The machine features a quick-change blade system, enabling operators to easily replace blades when necessary, further enhancing productivity.

Versatility is another hallmark of the RC5020, as it can be operated with various tractor sizes, making it an excellent choice for both small farms and larger agricultural operations. With a cutting width of 20 feet, it efficiently covers large areas, minimizing the time needed for mowing and land clearing. The cutter also boasts an adjustable cutting height, allowing users to set the machine to their specific requirements, whether it be trimming grasses or cutting back invasive brush.

Safety features are integrated into the design of the RC5020, ensuring operator protection. These include a heavy-duty chain guard that minimizes the risk of flying debris and a unique safety latch designed to keep the cutter securely closed during transport. Additionally, the easy-access maintenance points make routine inspections and servicing quick and straightforward.

In summary, the Land Pride RC5020 rotary cutter combines robust construction with advanced technology, making it an essential tool for anyone needing effective land management. Its versatility, efficient performance, and safety features make it an ideal choice for agricultural professionals and property owners alike. Whether for mowing grass or clearing larger brush areas, the RC5020 proves to be a reliable and powerful ally in maintaining landscapes with ease and efficiency.
Top Page Image Contents