Land Pride PR1672 manual PTO Hook-Up

Page 12

Table of Contents

Section 1: Assembly and Set-Up

Land Pride

PTO Hook-Up

If the Powered Rake is to be used on more than one tractor, an additional PTO shaft may be required - especially if a quick hitch is used.

!CAUTION

Do not use a PTO adaptor with a quick hitch. A PTO adapter will increase the strain on the tractor’s PTO shaft and can damage the PTO shaft and driveline.

IMPORTANT: Some tractors are equipped with multi-speed PTO ranges. Be certain your tractor ‘s PTO is set for 540 rpm.

IMPORTANT: Avoid premature driveline breakdown. A driveline that is operating must not exceed an angle of 25 degrees up or down while operating the 3-point lift. See Figure 1-2below.

13800

Maximum PTO driveline Movement During Operation

Figure 1-2

IMPORTANT: The PTO driveline may be too long for some tractors. If the Powered Rake is used on more than one tractor, an additional PTO driveline may be required.

IMPORTANT: Aligning the tractor’s PTO shaft level with the Powered Rake’s PTO shaft is necessary when checking to see if the driveline will fit correctly between tractor and Powered Rake.

Refer to Figure 1-3:

1.Start tractor and slowly engage tractor’s hydraulic 3-point to lift lower arms until the Powered Rake’s driveline shaft is approximately level with tractor's PTO shaft.

2.Slide outer yoke end of driveline over the tractor's PTO shaft and secure with the locking collar. Skip to step 4 if driveline fits between tractor and Powered Rake.

3.The driveline will require shortening if it is too long to fit between tractor and Powered Rake. Shorten driveline as follows:

a.Raise 3-point lower arms until Powered Rake and tractor PTO shafts are approximately level with each other. Securely block Powered Rake frame in this position. Set tractor in park, shut tractor engine off, set park brake and remove switch key.

b.Pull driveline apart into two sections as shown in Figure 1-3.Attach outer driveline universal joint to the tractor PTO shaft and inner driveline universal joint to the Powered Rake gearbox shaft. Pull on each driveline section to be sure the universal joints are secured to the shafts.

c.Hold driveline sections parallel to each other to determine if they are too long. The inner and outer shields on each section should end approximately 1" short of reaching the universal joint shield on the adjacent section (see “B” dimension). If they are too long, measure 1" (“B” dimension) back from the universal joint shield and make a mark at this location on the inner and outer driveline shields.

d.Cut off the inner shield at the mark (“X” dimension). Cut the same amount off the inner shaft (“X1” dimension). Repeat cut off procedure (“Y” & “Y1” dimensions) to the outer driveline half.

e.Remove all burrs and cuttings.

f.Apply multi-purpose grease to the inside of the outer shaft and reassemble the driveline.

g.Attach inner driveline yoke end to the Powered Rake gearbox input shaft.

h.Attach outer driveline yoke end to the tractor's PTO shaft.

22227

Driveline Shortening

Figure 1-3

4.The driveline should now be moved back and forth to insure that both ends are secured to the tractor and Powered Rake PTO shafts. Reattach any end that is loose.

10 PR1660, PR1672 & PR1690 Powered Rakes 314-216M

10/20/06

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Powered Rakes Table of Contents Important Safety Information Be Aware Signal WordsFor Your Protection Shutdown and StorageUse Safety Lights and Devices Practice Safe MaintenanceTransport Machinery Safely Keep Riders Off MachineryPrepare for Emergencies Wear Protective EquipmentAvoid High Pressure Fluids Hazard Safety Labels 818-255C818-230C 818-229C838-111C 818-552C818-130C 838-094C 818-540CUsing This Manual ApplicationOwner Assistance IntroductionAssembly and Set-Up Tractor RequirementsTractor Hook-Up Hydraulic OptionPTO Hook-Up Hydraulic Hook-up Optional Operating Checklist Operating Check ListTransporting Operating InstructionsOperating Instructions Adjustments Gauge WheelsRake Angle Material Control DeflectorDrive Chain Adjustment End PlatesMaintenance Slip Clutch MaintenanceMaintenance & Lubrication Slip Clutch with Hex Socket BoltsSlip Clutch with Hex Head Bolts Clutch Run-In with hex head boltsDrive Chain Maintenance Chain Case Skid Shoe ReplacementClutch Assembly with hex head bolts Sprocket and Chain Replacement Storage Lubrication HoursPivot Gauge Wheel SpindleRequired Drive ChainNon-Drive Bearing GearboxPR16 Series Powered Rake Specifications & CapacitiesPR1660 PR1672 PR1690 Features & Benefits Features BenefitsTroubleshooting Torque Values Chart for Common Bolt Sizes Tire Inflation ChartAppendix Warranty Overall Unit and Driveline One year Parts and LaborCorporate Office P.O. Box Salina, Kansas 67402-5060 USA

PR1672 specifications

The Land Pride PR1672 is a versatile and robust landscape rake designed for a variety of applications, including grading, leveling, and clearing debris from uneven terrains. With an impressive working width of 72 inches, this rake is suitable for use with compact tractors and utility vehicles, making it an ideal choice for both professional landscapers and homeowners looking to maintain their properties.

One of the key features of the PR1672 is its heavy-duty construction. Built with high-quality materials, the rake is engineered to withstand the rigors of tough landscaping tasks. The 3-point hitch attachment allows for easy connection to a wide range of tractors, ensuring compatibility and ease of use. The adjustable side rails enhance its functionality, enabling operators to control the depth of the rake and optimize its performance based on varying soil conditions and desired outcomes.

The rake’s design includes curved tines that are strategically spaced to effectively gather and redistribute soil, gravel, and other materials. This innovative tine design helps in achieving a smooth finish while minimizing the likelihood of clogging, which can be a common issue with traditional rakes. Additionally, the tines are replaceable, making maintenance straightforward and extending the tool’s overall lifespan.

Incorporating advanced manufacturing techniques, the PR1672 features a durable powder-coated finish that provides resistance against rust and corrosion. This ensures that the rake can endure various weather conditions and remains effective for years to come. The implement also benefits from Land Pride's commitment to safety, with features designed to protect both the user and the equipment being operated.

The versatility of the PR1672 extends beyond mere landscaping. It can also be employed in agriculture, helping to prepare seedbeds or maintain farm roads. Its adaptability makes it an invaluable tool for anyone looking to improve their outdoor spaces efficiently.

Overall, the Land Pride PR1672 is an essential piece of equipment that delivers reliability and performance. With its robust build, smart design features, and user-friendly operation, it stands out as an excellent solution for those looking to take on challenging outdoor tasks while achieving professional results. Whether tackling residential projects or commercial landscapes, the PR1672 is equipped to handle the job with ease.
Top Page Image Contents