Land Pride PR1672 manual Operating Instructions

Page 15

Land Pride

Section 2: Operating

Table of Contents

Operating Instructions continued

First completely familiarize yourself with the Operator’s Manual. Then complete the Operator’s checklist, properly attach the Powered Rake to your tractor, make initial depth setting, level settings and roller angle adjustments.

After completing the above, you will need to choose a work site, perform operational safety checks and make final adjustments before using your Land Pride Powered Rake.

IMPORTANT: Shut off all power, disengage PTO, set park brake and remove ignition key any time the Powered Rake is not operating properly or needs adjustment.

It’s now time for a running operational safety check. Make certain that the tractor’s park brake is engaged, PTO is disengaged and the Powered Rake is resting on the ground. Start the tractor and back off engine rpm to approximately one-quarter throttle. Using the rear draft link hydraulic control, lift the Powered Rake about half way off the ground and then engage the rear PTO. If everything is running smoothly, increase throttle speed until you have reached full operating speed. Never engage the tractor PTO at full engine rpm., damage to the driveline and/or Powered Rake could occur.

To make final adjustments, choose a work site that is dry and allows you to make at least a 50 ft. straight run. Raise the Powered Rake half way off the ground, disengage the tractor PTO, release the park brake and travel to your starting point. Travel speed should be between 3 and 5 mph.

Once at the site, idle the tractor engine, engage the PTO and then increase engine speed until the tractor is at full 540 rpm operating speed. Begin traveling forward while gently lowering the running Powered Rake to the ground. Make slight changes to the tractor’s ground speed as you travel forward to determine the desired ground finish.

Generally, a slower speed results in a finer finish, while a higher speed results in a coarser finish. Excessive ground speed may result in dirt or material passing over the top of the material control deflector or too much material being windrowed off to the side. Powered Rakes do not perform well in wet sticky soil. Avoid making sharp turns or backing-up when in contact with the ground.

Normal operating rake angle is 15 degrees left or right. However, you may want to make subtle hydraulic adjustments to the roller angle to determine varying effect on the surface finish.

You can also vary the effect on the surface finish by setting the material control deflector height above the roller. The material control deflector sifts out clods, rocks and other debris as the soil passes over the top of the roller. Adjusting the blade down decreases the gap between the deflector and roller and will sift out more objects for a finer soil finish. Adjusting the blade up

allows more clods, rocks and debris to pass over the roller and produces a coarser soil finish.

Set the working depth and level the rake at the caster gauge wheels and not with the tractor. Normally a one- inch cultivation depth is considered ideal for a surface finish. Make adjustments to the working depth if too many rocks or excessive debris pass under the roller by changing the C-spacers on the gauge wheel spindles. Increase working depth by moving the spacers from below the support arms to above the support arms. Decrease working depth by moving the spacers from above the gauge wheel support arms to below the support arms.

The Powered Rake should also be set to operate level. It has a tendency to go in deeper on the driveline side (left side) because that is the heavy side of the rake.

Compensate for this by changing the C-spacers on the right gauge wheel so that it is set approximately 1” deeper than the left gauge wheel.

After you have traveled 50 feet, properly shut down the tractor and Powered Rake to inspect the finish and determine what, if any, additional adjustments need to be made. Check for any foreign objects that may be wrapped around the roller or lodged between moving parts.

Remember that the right finish is achieved through a combination of proper soil moisture conditions, operating depth, ground speed, material control deflector opening and roller angle. Your Powered Raking capabilities will improve rapidly with experience.

10/20/06

PR1660, PR1672 & PR1690 Powered Rakes 314-216M

13

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Powered Rakes Table of Contents Shutdown and Storage Important Safety InformationBe Aware Signal Words For Your ProtectionKeep Riders Off Machinery Use Safety Lights and DevicesPractice Safe Maintenance Transport Machinery SafelyPrepare for Emergencies Wear Protective EquipmentAvoid High Pressure Fluids Hazard 818-255C Safety Labels818-229C 818-230C838-111C 818-552C818-130C 818-540C 838-094CIntroduction Using This ManualApplication Owner AssistanceHydraulic Option Assembly and Set-UpTractor Requirements Tractor Hook-UpPTO Hook-Up Hydraulic Hook-up Optional Operating Instructions Operating ChecklistOperating Check List TransportingOperating Instructions Material Control Deflector AdjustmentsGauge Wheels Rake AngleEnd Plates Drive Chain AdjustmentSlip Clutch with Hex Socket Bolts MaintenanceSlip Clutch Maintenance Maintenance & LubricationClutch Run-In with hex head bolts Slip Clutch with Hex Head BoltsDrive Chain Maintenance Chain Case Skid Shoe ReplacementClutch Assembly with hex head bolts Sprocket and Chain Replacement Storage Gauge Wheel Spindle LubricationHours PivotGearbox RequiredDrive Chain Non-Drive BearingPR16 Series Powered Rake Specifications & CapacitiesPR1660 PR1672 PR1690 Features Benefits Features & BenefitsTroubleshooting Torque Values Chart for Common Bolt Sizes Tire Inflation ChartAppendix Overall Unit and Driveline One year Parts and Labor WarrantyCorporate Office P.O. Box Salina, Kansas 67402-5060 USA

PR1672 specifications

The Land Pride PR1672 is a versatile and robust landscape rake designed for a variety of applications, including grading, leveling, and clearing debris from uneven terrains. With an impressive working width of 72 inches, this rake is suitable for use with compact tractors and utility vehicles, making it an ideal choice for both professional landscapers and homeowners looking to maintain their properties.

One of the key features of the PR1672 is its heavy-duty construction. Built with high-quality materials, the rake is engineered to withstand the rigors of tough landscaping tasks. The 3-point hitch attachment allows for easy connection to a wide range of tractors, ensuring compatibility and ease of use. The adjustable side rails enhance its functionality, enabling operators to control the depth of the rake and optimize its performance based on varying soil conditions and desired outcomes.

The rake’s design includes curved tines that are strategically spaced to effectively gather and redistribute soil, gravel, and other materials. This innovative tine design helps in achieving a smooth finish while minimizing the likelihood of clogging, which can be a common issue with traditional rakes. Additionally, the tines are replaceable, making maintenance straightforward and extending the tool’s overall lifespan.

Incorporating advanced manufacturing techniques, the PR1672 features a durable powder-coated finish that provides resistance against rust and corrosion. This ensures that the rake can endure various weather conditions and remains effective for years to come. The implement also benefits from Land Pride's commitment to safety, with features designed to protect both the user and the equipment being operated.

The versatility of the PR1672 extends beyond mere landscaping. It can also be employed in agriculture, helping to prepare seedbeds or maintain farm roads. Its adaptability makes it an invaluable tool for anyone looking to improve their outdoor spaces efficiently.

Overall, the Land Pride PR1672 is an essential piece of equipment that delivers reliability and performance. With its robust build, smart design features, and user-friendly operation, it stands out as an excellent solution for those looking to take on challenging outdoor tasks while achieving professional results. Whether tackling residential projects or commercial landscapes, the PR1672 is equipped to handle the job with ease.
Top Page Image Contents