Land Pride ZRP44 Deck Drive Belt, Integrated Pump/Motor Drive Belt, Refer to -11, -12, and Figure

Page 33

Land Pride

Table of Contents

Section 4 Maintenance and Lubrication

Deck Drive Belt

1.Park the unit on a flat surface. Stop the engine and remove the ignition key. Make sure blade engagement switch is in the down (OFF) position. Place control levers in the park brake position. Disconnect negative battery cable.

2.Place the deck in the lowest position.

3.Remove the deck belt covers and floor panel.

4.Release the deck belt tension by pulling on the belt tension chain and sliding the chain out of the anchor bracket slot. This will relieve the tension on the deck belt idler spring. Refer to Figure 4-11.

5.Pull the idler to the left of the machine to provide maximum belt clearance.

6.Remove the existing belt and replace with a new belt.

7.Route the new belt per Figure 4-11.

8.Re-tension the deck belt idler per the deck drive belt adjustment section on page 18.

9.Re-install the deck belt covers.

10.Re-attach the negative battery cable and floor panel.

Integrated Pump/Motor Drive Belt

Refer to Figure 4-11, Figure 4-12, and Figure 4-13

Replace hydraulic pump motor drive belt as follows:

1.Park the unit on a flat surface. Stop the engine and remove the ignition key. Make sure blade engagement switch is in the down (OFF) position. Place control levers in the park brake position. Disconnect negative battery cable.

2.Place the deck in the lowest position.

3.Refer Figure 3-13 on page 18 and Figure 4-11on this page. Release the deck belt tension by pulling on the belt tension chain and sliding the chain out of the anchor bracket slot.

4.Remove deck drive belt from the electric clutch pulley mounted to the engine. This belt does not need to be removed from any of the other pulleys.

5.Release the tension from the integrated pump/motor belt by pulling on the idler pulley extension spring carefully until the belt can be slide over the idler pulley. Use caution when releasing the idler pulley as there is still tension on it and it will snap back into position.

5

2

3

6

1

21077

2

42

5

Deck Belt Drive Layout

1.Spindle drive belt

2.Deck blade spindle pulley

3.Spindle belt tension idler

4.Spindle belt tension idler spring (9.0” at operation)

5.Deck belt idler

6.Idler arm

Pump Belt Layout

 

1.

Pump belt

 

2.

Engine pulley

 

3.

Pump idler pulley

 

4.

Pump idler arm

 

5.

Pump pulley

 

6.

Electric Deck Clutch

 

7.

Pump idler spring

 

 

 

1

 

 

5

 

 

4

 

5

 

 

2,6

7

 

 

21078

3

Deck Belt Drive Layout

Mower Viewed from Bottom Deck

Figure 4-11

Figure 4-12

7/14/08

ZRP44 & ZRP52 Zero Turning Radius Mowers 356-117M

31

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Accu-Z Razor ProTable of Contents Be Aware of Signal Words Important Safety InformationKeep Riders Off Machinery For Your ProtectionSafety at All Times Practice Safe MaintenancePrepare for Emergencies Wear Protective EquipmentAvoid High Pressure Fluids Hazard 838-305C 838-303C838-306C 818-543C838-308C 838-307C838-310C 838-399CApplication Using This ManualOwner Assistance IntroductionControl Lever & Seat Assembly Assembly and Set-UpRefer to Figure Controls Ignition SwitchOperating Throttle ControlLeft/Right Fuel Tank Valve Blade Engagement SwitchControl Levers Deck Lift PedalInstrumentation Safety Start Interlock SystemEngine Starting Oil Pressure LightDriving the Mower Moving Mower with Stalled EngineRefer to -8 on Operating Suggestions Operating Instructions Mower Deck OperationIntroduction AdjustmentsTorque Values Steering LinkageControl lever stops Control Lever Neutral AdjustmentControl Lever Adjustment Park Brake AdjustmentSteering Dampener Control Lever Position Travel Slot Park Brake Outside Edge Deck Drive Belt Adjustment Hydro-Drive Belt AdjustmentDeck Leveling and Height Adjustment Engine RPM SettingTire Inflation Chart Deck Level AdjustmentsNut Deck Lift Threaded Rod Deck Cutting Height Adjustment Anti-Scalp RollersRefer to Refer to Figure Hydraulic Oil Heat Exchanger Maintenance and LubricationVerify Safety Start Interlock System Daily Maintenance TiresSolid fill tires are not to be used on the Razor Pro mowers Hour Meter LubricationElectrical System Access to Engine & Hydraulic Pumps Burnishing the Electric ClutchHydraulic System Fuel System Draining the fuel tank Changing fuel filtersRefer to -8A and -8B Engine Air Filter Engine Oil and FilterRefer to -9A and -9B Over ServicingGeneral Engine Maintenance Engine Air Filter Service ProcedureBelt Replacement Refer to -11 and FigureIntegrated Pump/Motor Drive Belt Deck Drive BeltRefer to -11, -12, and Figure Deck Belt Drive LayoutMower Blade Maintenance Mower Blade Removal and SharpeningRefer to -14 and -15 on New Season Preparation Preparation of Engine for StorageSpecifications and Capacities ZRP44 & ZRP52 Razor Pro Riding Mowers Engine SpecificationsZRP44 & ZRP52 Razor Pro Riding Mowers General Specifications Safety Features Brake ServiceIndicators Hydraulic Pump DriveFeatures and Benefits FeaturesZRP44 & ZRP52 Razor Pro Riding Mowers Troubleshooting Mower creeps when parking brake Mower creeps when steering controlOil Light is on when engine is Oil in reservoir smells rancidTire Appendix40 ZRP44 & ZRP52 Zero Turning Radius Mowers 356-117M 14/08 Hydraulic Wheel Motors and Pumps 2 years on Parts and Labor WarrantyCorporate Office P.O. Box Salina, Kansas 67402-5060 USA
Top Page Image Contents