Land Pride AFM4016 manual PTO To Drawbar Set-Up, Tractor Hook-up

Page 16

Table of Contents

Section 1: Assembly and Set-up

Land Pride

PTO To Drawbar Set-Up

Refer to Figure 1-2

Distances between center of drawbar hitch pin hole to end of tractor PTO shaft (“A” dimension) and from top of drawbar hitch to center of PTO shaft (“B” dimension) must be maintained.

22273

PTO to Drawbar Distances

Figure 1-2

•“A” = 14" for 540 rpm

•“B” = 8” for 540 rpm

IMPORTANT: PTO damage may occur if distances “A” and “B” are not properly maintained.

Tractor Hook-up

Refer to Refer to Figure 1-3:

4.Back the tractor up close to the hitch. Level the mower frame with the tongue jack.

5.Adjust the mower’s hitch to the tractors draw bar height.

6.Attach the mower with a 3/4" hitch pin and secure it with the lock pin. Always use a pin that contains a safety locking device to prevent it from falling out.

7.Retract the tongue jack until the weight of the mower is fully removed from the jack, then remove the jack. Store the jack on the storage tube located on top of the divider gear box.

8.Attach the safety chain on the frame tongue to the tractor. Adjust the chain length to remove all slack except what is necessary to permit turning of the mower. Lock the hook securely on the chain.

9.The driveline shaft from the tractor is a constant velocity type. Always attach the end with the constant velocity joint to the tractor output shaft. Attach the other end to the splined input shaft on the divider gear box on the transport frame.

10.Move the driveline back and forth to insure that it is secured on the shaft of the tractor and power divider input shaft on the mower.

11.Secure the chain on the driveline around mower frame to restrict the outer shield of the driveline from rotating.

NOTE: A chain is supplied with each driveline. This chain must be attached to the shield cone of each driveline and to an anchor on the mower deck or hitch.

12.Should the driveline shaft require shortening:

a.Hold the half shafts next to each other in the shortest working position and mark them.

b.Shorten inner and outer guard tubes equally.

c.Shorten inner and outer sliding profiles by the same length as the guard tubes.

d.Proper overlap is a minimum of one-half the length of each tube, with both tubes being of equal length.

e.Round off all sharp edges and remove burrs. Grease sliding profiles.

13.Route the cylinder hoses through the hose support loop and connect to tractor remote outlets. Refer to Hydraulic Plumbing, this section on page 13, for proper hookup. Quick disconnect hydraulic fittings for your tractor are supplied with mower.

Mower to Tractor Hook-up

14918

Figure 1-3

 

 

 

14

AFM4011, AFM4014 and AFM4016 All Flex Grooming Mowers 315-160M

7/28/06

Page 15 Page 17
Image 16
Page 15 Page 17
Contents All Flex Grooming Mowers Table of Contents For Your Protection Be Aware Signal WordsShutdown and Storage Transport Machinery Safely Use a Safety ChainPractice Safe Mainte- nance Tire Safety Wear Protective EquipmentAvoid High Pressure Fluids Hazard Keep Riders Off Machinery818-019C 818-003C818-130C 818-187C 818-229C 818-230C818-337C 818-337C 818-339C 818-351C818-351C 818-353C 818-556C 818-555C818-558C 818-561C 818-456C 818-513C 818-552C 818-540CApplication Using This ManualOwner Assistance Land Pride Service Department East North Street Tractor Requirements Hydraulic PlumbingPTO To Drawbar Set-Up Tractor Hook-upBleeding The Fold Hydraulics Joint Timing IntroductionTransporting Pre-Operation Instructions Constant Velocity Driveline AngleOperating Check List Operating Instructions General Operating InstructionsTable of Contents Center Deck Height Adjustments Cutting Height ChartBelt Tension Adding or Replacing SpacersBall Swivel Hitch Accessory Part NumbersCutting Blades Servicing Mower Blades MaintenanceBlade Inspection Blade Removal And Installation Refer to -2 & FigureBlade Sharpening Blade OptionsBelt Installation Refer to -8& FigureDriveline Protection Clutch Run-InClutches With 8-Alan Head Socket Bolts Clutches With 4-Tightening NutsClutch Assembly Assembly DisassemblyStep Storage Tires With Air PressureLubrication Points HoursDriveline Constant Velocity Shaft Driveline ShaftsWheel Support Bushings Inner Tube of DrivelineWheel Bushings Gauge Wheels Seasonally Wheel Bushings Transport HubsBearing in Blade Spindle Hubs Way Gear Box RequiredMower Deck Gear Box Description Specification / Capacity Model AFM4011 All-Flex Grooming Mower12701 AFM4014 Series 14044 Description Specification / Capacity AFM4016 Series13665 Features Benefits AFM4014 All-Flex Grooming MowerAFM4016 All-Flex Grooming Mower Narrow 6’8 transport widthTroubleshooting Problem Cause Solution Discharge openings Torque Values Chart for Common Bolt Sizes Tire Inflation ChartIn-tpi Ft-lb Model Models 4014 TireSize InflationWarranty Overall Unit and Driveline One year Parts and LaborCorporate Office P.O. Box Salina, Kansas 67402-5060 USA
Related manuals
Manual 114 pages 59.01 Kb

AFM4016 specifications

The Land Pride AFM4016 is a versatile and robust asset designed for agricultural professionals seeking to optimize their land management operations. This 16-foot-wide aircraft mower is equipped to handle a variety of mowing tasks, from pasture maintenance to roadside trimming. Its sturdy construction ensures it can withstand the rigors of demanding environments while delivering impressive performance.

One of the primary features of the AFM4016 is its unique folding design, which allows for easy transport between mowing sites. When the mower is in transport mode, it can be safely narrowed to comply with road regulations without sacrificing cutting width or efficiency. This flexibility makes it a perfect companion for farmers who need to move their equipment frequently.

Technologically, the AFM4016 is engineered with advanced features such as its reliable gear-driven design that provides high torque for efficient cutting. This setup ensures that the mower operates smoothly in various conditions, reducing wear and tear while enhancing longevity. The reinforced steel frame factors heavily into the mower’s durability, allowing it to endure tough terrains such as rocky fields or heavy brush.

The AFM4016 also boasts a powerful cutting system that utilizes dual rotary blades, which work in tandem to create a clean and even cut. This feature not only improves aesthetic appeal but also promotes healthier regrowth of grass and forage, crucial for livestock farmers. The mower height can be easily adjusted, accommodating different types of vegetation and allowing for customization based on specific mowing needs.

In terms of operational efficiency, the Land Pride AFM4016 is designed for compatibility with a wide range of tractors, making it a versatile choice for various agricultural setups. The quick-attach hitch system enables fast and easy mounting and dismounting, enhancing productivity through reduced downtime.

Safety is a paramount consideration, and the AFM4016 comes with built-in safety features including shields that protect the operator from debris while mowing. The mower’s stability on slopes is also an important characteristic, allowing for safe operation on uneven terrains.

Overall, the Land Pride AFM4016 is an exceptional tool for land management. Its combination of durability, versatility, and advanced technology ensures that it meets the demanding needs of agricultural professionals, making it an invaluable addition to any farming operation. With this high-performance mower, users can maintain their land effectively and efficiently while achieving optimal results.
Top Page Image Contents