Operating Instructions

Table of Contents

Section 2: Operating Instructions

Land Pride

!DANGER!

Stop operation if bystanders come within several hundred feet

!WARNING!

Do not operate mower in raised position.

•Extend all 3 cylinders to their maximum stroke for maximum field float of mower decks.

IMPORTANT: When unfolding the mower, fully extend the fold cylinders to utilize maximum flexibility. Damage to the mower may occur if the cylinders are not fully extended.

7.Set the tractor throttle at idle. Engage the PTO to start the blades rotating.

!WARNING!

Operate mower with guards installed and in good condition. Keep away from moving parts.

!WARNING!

The following operating procedures must be carefully read and fully understood. You are the tractor operator and are therefore responsible for the safe operation of this unit. All other persons must be cleared of the area. Cutter operation must be stopped when in the vicinity of other persons.

1.After attaching the tractor to the mower, carefully check all hoses and wires to be sure they will not contact the PTO driveline.

2.Check PTO guards to make sure they are in good condition and in place.

3.Inspect Hydraulic hoses for wear, damage and hydraulic leaks. See “Avoid High Pressure Fluids Hazard” on page 3. Replace damaged and worn hoses with genuine Land Pride parts.

4.Check the following after the PTO has been disengaged and come to a complete stop. Wear your safety glasses.

•Check mower blades for sharpness.

•Ensure that bolts and nuts are tight.

•Check tractor safety equipment. To be sure they are in good working condition.

5.On 4016 models only: Refer to Figure 2-3 on page 17. Remove the deck floating pins before unfolding mower decks.

!CAUTION!

Before unfolding the mower make sure the transport locks are unlatched. Unlatch locks by pulling the rope.

6.Refer to Figure 2-2 on page 16. Lower the mower decks to the ground by:

•Retracting the hydraulic cylinders to remove weight from the transport locks.

•Pull the transport lock rope toward the tractor to disengage the locks.

•Hold locks in this position until all 3 mower decks have unfolded enough to allow the lock lugs to become fully disengaged.

8.At first, begin mowing at a slow forward speed and shift up until the desired speed is achieved - maintaining 540 PTO rpm. Mower blades will cut better at 540 PTO blade speed than at reduced throttle.

9.After mowing the first 50 feet, stop and check to see that the mower is adjusted properly.

10.Grass is best cut when it is dry. Mowing wet grass can cause plugging resulting in grass clumps behind the mower.

11.Grass should be mowed frequently as shorter clippings deteriorate faster.

12.When mowing extremely tall grass, it is best to raise the cutting height and mow the area, then lower the cutting height and mow a second time at the desired height.

For a guide on measuring the cutting height refer to the Cutting Height Chart on page 20.

IMPORTANT: Do not engage PTO with mower decks in the raised position or with engine speed above idle. Doing so will cause damage to the power train components.

IMPORTANT: Do not exceed rated PTO speed of the mower. Excessive engine speed will cause damage to the power train components.

IMPORTANT: Avoid catching the hydraulic hoses on brush, post, stumps, and other protrusions that could damage and/or break them.

General Operating Instructions

By now you should have familiarized yourself with the Operator’s Manual, completed the Operator’s Checklist, set-up the unit properly and attached your Land Pride All-Flex mower to your tractor.

With the tractor’s park brake engaged and the PTO disengaged, start the tractor. Using the tractor’s hydraulic control levers, retract the hydraulic deck-lift cylinders all the way in and pull the ropes leading to your transport locks to release them. With the same control levers, slowly lower your mowing decks from transport position to working position on the ground. Having lowered the decks, shut the tractor off, check to make sure the park brake is set and remove the switch key. Dismount from the tractor and preset your mower to the desired cutting height.

AFM4011, AFM4014 and AFM4016 All Flex Grooming Mowers 315-160M

7/28/06

AFM4016 specifications

The Land Pride AFM4016 is a versatile and robust asset designed for agricultural professionals seeking to optimize their land management operations. This 16-foot-wide aircraft mower is equipped to handle a variety of mowing tasks, from pasture maintenance to roadside trimming. Its sturdy construction ensures it can withstand the rigors of demanding environments while delivering impressive performance.

One of the primary features of the AFM4016 is its unique folding design, which allows for easy transport between mowing sites. When the mower is in transport mode, it can be safely narrowed to comply with road regulations without sacrificing cutting width or efficiency. This flexibility makes it a perfect companion for farmers who need to move their equipment frequently.

Technologically, the AFM4016 is engineered with advanced features such as its reliable gear-driven design that provides high torque for efficient cutting. This setup ensures that the mower operates smoothly in various conditions, reducing wear and tear while enhancing longevity. The reinforced steel frame factors heavily into the mower’s durability, allowing it to endure tough terrains such as rocky fields or heavy brush.

The AFM4016 also boasts a powerful cutting system that utilizes dual rotary blades, which work in tandem to create a clean and even cut. This feature not only improves aesthetic appeal but also promotes healthier regrowth of grass and forage, crucial for livestock farmers. The mower height can be easily adjusted, accommodating different types of vegetation and allowing for customization based on specific mowing needs.

In terms of operational efficiency, the Land Pride AFM4016 is designed for compatibility with a wide range of tractors, making it a versatile choice for various agricultural setups. The quick-attach hitch system enables fast and easy mounting and dismounting, enhancing productivity through reduced downtime.

Safety is a paramount consideration, and the AFM4016 comes with built-in safety features including shields that protect the operator from debris while mowing. The mower’s stability on slopes is also an important characteristic, allowing for safe operation on uneven terrains.

Overall, the Land Pride AFM4016 is an exceptional tool for land management. Its combination of durability, versatility, and advanced technology ensures that it meets the demanding needs of agricultural professionals, making it an invaluable addition to any farming operation. With this high-performance mower, users can maintain their land effectively and efficiently while achieving optimal results.