Land Pride AFM4016 manual Table of Contents

Page 21

Land Pride

Table of Contents

Section 2: Operating Instructions

It’s now time to do a running operational safety check. It is extremely important that if at any time during this safety check you detect a malfunction in either the mower or tractor that you immediately shut the tractor off, remove the key and set the park brake. Make necessary repairs and/or adjustments before continuing on.

Make sure before starting the tractor that the mower is properly attached to the draw bar with both wings down resting on the ground. Also make sure the driveline is securely coupled to the tractor’s PTO shaft, the hydraulic hoses are properly attached to the tractor’s hydraulics, the tractor’s park brake is engaged and the tractor’s PTO drive is disengaged. Starting the tractor and set the engine throttle speed at a low idle. Engage the tractor’s PTO drive. If everything is running smoothly, slowly increase the engine rpm until the tractor’s engine reaches full PTO operating speed of 540 rpm. If everything is still running as it should, then return the engine to low idle and disengage power to the PTO. Under no circumstances should you ever raise the cutting decks into transport position with the PTO drive engaged. Personal injury and machine damage could result.

You should now be ready to move to your cutting site to begin mowing. On roadway transport in such a manner that faster moving vehicles can easily see you and pass you safely. Reduce your speed when traveling over rough and hilly terrain. Avoid quick or sharp steering corrections. Take extra care to insure that the mower doesn’t come into contact with obstacles such as trees, buildings or fences. Use accessory lights and appropriate reflective devices to provide adequate warning to pedestrians and other vehicle operators when traveling on public roads and in the dark of night. Comply with all local, state and federal laws.

It is important that you inspect the area where you will be cutting and clear it of safety hazards and foreign objects either before or after you arrive at the cutting site. Never assume the area is clear. Cut only in areas you are familiar with and are free of debris and unseen objects. In the event you do strike an object, stop the mower and tractor immediately to inspect and make any necessary repairs before resuming operation. It really pays to inspect a new area and to develop a safe plan before mowing.

You will need to maintain a ground speed between 2-6 mph and 540 rpm PTO speed to produce a clean cut. Make a tractor gear and range selection that will enable you to maintain these speed combinations. Generally the quality of cut is better at lower ground speeds. Dense ground cover will create the need to slow down even more. In certain conditions tractor tires will roll grass down resulting in an uneven cut when the grass fails to rebound. Should this happen you may try reversing the direction of cut and/or double cut to achieve the desired finish.

Avoid very low cutting heights especially on extremely uneven terrain. Always cut downward on slopes and avoid crossing the face of steep slopes. Avoid sharp drops and cross diagonally through dips to prevent hanging up the tractor and cutter. Slow down in turns and avoid sharp turns if at all possible. Remember to look back often.

Now you’re prepared and well briefed you may begin cutting. Begin cutting by doing the following:

•Reducing the tractor’s engine rpm.

•Make sure the mower is on the ground in cutting position.

•Engage the PTO.

•Raise the engine rpm to the appropriate PTO speed.

•Begin mowing.

Make wide turns when possible. Operators of pull-type models must plan ahead and choose a cutting pattern that allows for wider turns. Try increasing or decreasing ground speed to determine the effect on quality of cut. With a little practice you will be pleased with what you and your Land Pride All-Flex Mower can do.

Whether you are done mowing, need to take a break, or just need to make a few adjustments to the mower, remember to always do the following:

•Reduce the tractor’s engine rpm.

•Disengage the PTO.

•Stop on level ground.

•Set the park brake.

•Turn off the engine and remove the key.

•Stay on the tractor until the mower blades have come to a complete stop.

7/28/06

AFM4011, AFM4014 and AFM4016 All Flex Grooming Mowers 315-160M 19

Page 20 Page 22
Image 21
Page 20 Page 22
Contents All Flex Grooming Mowers Table of Contents Be Aware Signal Words For Your ProtectionShutdown and Storage Use a Safety Chain Transport Machinery SafelyPractice Safe Mainte- nance Wear Protective Equipment Tire SafetyAvoid High Pressure Fluids Hazard Keep Riders Off Machinery818-003C 818-019C818-230C 818-130C 818-187C 818-229C818-337C 818-339C 818-351C 818-337C818-555C 818-351C 818-353C 818-556C818-558C 818-561C 818-456C 818-513C 818-540C 818-552CUsing This Manual ApplicationOwner Assistance Land Pride Service Department East North Street Hydraulic Plumbing Tractor RequirementsTractor Hook-up PTO To Drawbar Set-UpBleeding The Fold Hydraulics Introduction Joint TimingTransporting Constant Velocity Driveline Angle Pre-Operation InstructionsOperating Check List General Operating Instructions Operating InstructionsTable of Contents Cutting Height Chart Center Deck Height AdjustmentsAdding or Replacing Spacers Belt TensionAccessory Part Numbers Ball Swivel HitchCutting Blades Maintenance Servicing Mower BladesBlade Inspection Refer to -2 & Figure Blade Removal And InstallationBlade Options Blade SharpeningRefer to -8& Figure Belt InstallationClutch Run-In Driveline ProtectionClutches With 8-Alan Head Socket Bolts Clutches With 4-Tightening NutsClutch Assembly Disassembly AssemblyStep Tires With Air Pressure StorageHours Lubrication PointsDriveline Constant Velocity Shaft Driveline ShaftsInner Tube of Driveline Wheel Support BushingsWheel Bushings Gauge Wheels Wheel Bushings Transport Hubs SeasonallyBearing in Blade Spindle Hubs Required Way Gear BoxMower Deck Gear Box Model AFM4011 All-Flex Grooming Mower Description Specification / Capacity12701 AFM4014 Series 14044 AFM4016 Series Description Specification / Capacity13665 AFM4014 All-Flex Grooming Mower Features BenefitsNarrow 6’8 transport width AFM4016 All-Flex Grooming MowerTroubleshooting Problem Cause Solution Discharge openings Tire Inflation Chart Torque Values Chart for Common Bolt SizesIn-tpi Ft-lb Model Models 4014 TireSize InflationOverall Unit and Driveline One year Parts and Labor WarrantyCorporate Office P.O. Box Salina, Kansas 67402-5060 USA
Related manuals
Manual 114 pages 59.01 Kb

AFM4016 specifications

The Land Pride AFM4016 is a versatile and robust asset designed for agricultural professionals seeking to optimize their land management operations. This 16-foot-wide aircraft mower is equipped to handle a variety of mowing tasks, from pasture maintenance to roadside trimming. Its sturdy construction ensures it can withstand the rigors of demanding environments while delivering impressive performance.

One of the primary features of the AFM4016 is its unique folding design, which allows for easy transport between mowing sites. When the mower is in transport mode, it can be safely narrowed to comply with road regulations without sacrificing cutting width or efficiency. This flexibility makes it a perfect companion for farmers who need to move their equipment frequently.

Technologically, the AFM4016 is engineered with advanced features such as its reliable gear-driven design that provides high torque for efficient cutting. This setup ensures that the mower operates smoothly in various conditions, reducing wear and tear while enhancing longevity. The reinforced steel frame factors heavily into the mower’s durability, allowing it to endure tough terrains such as rocky fields or heavy brush.

The AFM4016 also boasts a powerful cutting system that utilizes dual rotary blades, which work in tandem to create a clean and even cut. This feature not only improves aesthetic appeal but also promotes healthier regrowth of grass and forage, crucial for livestock farmers. The mower height can be easily adjusted, accommodating different types of vegetation and allowing for customization based on specific mowing needs.

In terms of operational efficiency, the Land Pride AFM4016 is designed for compatibility with a wide range of tractors, making it a versatile choice for various agricultural setups. The quick-attach hitch system enables fast and easy mounting and dismounting, enhancing productivity through reduced downtime.

Safety is a paramount consideration, and the AFM4016 comes with built-in safety features including shields that protect the operator from debris while mowing. The mower’s stability on slopes is also an important characteristic, allowing for safe operation on uneven terrains.

Overall, the Land Pride AFM4016 is an exceptional tool for land management. Its combination of durability, versatility, and advanced technology ensures that it meets the demanding needs of agricultural professionals, making it an invaluable addition to any farming operation. With this high-performance mower, users can maintain their land effectively and efficiently while achieving optimal results.
Top Page Image Contents