Land Pride RCR2584 manual Trail-Type Cutter, Hitch Assembly

Page 12

Table of Contents

Section 1 Assembly and Setup

Land Pride

Trail-Type Cutter

Hitch Assembly

NOTE: Do not tighten hardware until assembly is complete. Refer to “Torque Values Chart for Common Bolt Sizes” on page 27.

Refer to Figure 1-5:

1.Assemble tongue weldment (#1) to deck weldment using two hitch pins (#2), spacer tubes (#3) and lynch pins (#4).

2.Attach the bearing support assembly (#5) to the tongue (#1) with two bushings (#6), flat washers (#7), lock washers (#8), nut (#9) and bolt (#10).

3.Attach level rod assembly (#11) to the tongue weld- ment (#1) using two clevis pins (#12), flat washers (#13) and hair pin cotters (#14). Make sure that the adjusting nut on the level rod assemblies is threaded the same distance on both level rod weldment long and level rod weldment short. This will ensure a level unit.

4.Mount hose holder bracket (#17) to the deck with the 3/4” -10 x 1 1/2” long bolt (#18) and lock nut (#19).

5.Fasten hose holder (#20) to the hose holder bracket (#17) with a 3/8” -16 x 1 1/2” long bolt (#21), flat washer (#22) and lock nut (#23).

Driveline Installation

1.Remove wing nut holding gearbox shield and flip up and out of the way.

2.Attach the slip clutch end of the jackshaft to the gear- box input shaft securely. Make certain that the slip clutch is fully onto the input shaft splines. Tighten the two lock nuts on back side of slip clutch alternately un- til they have reached the proper torque.

3.Swing gearbox shield back into place and re-install the wing nut and tighten.

4.Insert jackshaft (#15) through bearing support assem- bly (#5).

NOTE: Be sure lock collar is to the rear.

Install main driveline to jackshaft by attaching (red) slide collar to jackshaft. Twist the quick disconnect on the yoke and push it forward to engage the groove on the splined stub on the jackshaft.

5.Secure chain on driveline (#16) to bearing support as- sembly (#5) to restrict outer shield from rotating. Se- cure chain on driveline (#15) to level rod weldment to restrict outer shield from rotating.

14386

Trail-Type Tongue Assembly

Figure 1-5

10 RCR2584 Rotary Cutter 312-459M

7/14/08

Image 12
Contents Operator’st ’s Manuall Rotary CutterTable of Contents Be Aware of Signal Words Keep Riders Off MachineryFor Your Protection Shutdown and StorageUse Safety Lights and Devices Practice Safe MaintenancePrepare for Emergencies Wear Protective EquipmentTable of Contents Safety Labels 818-130C 818-187C818-230C 818-540C818-552C 818-830C 838-094CUsing This Manual Owner AssistancePoint Hitch Assembly Point Quick Hitch AssemblyDriveline Installation Tractor RequirementsSingle Tailwheel Assembly Dual Tailwheel AssemblyHitch Assembly Trail-Type CutterSafety Guards Axle AssemblyRear Chain Guard Front Chain GuardTractor Hook-Up Point Tractor Hook-UpTrail-Type Tractor Hook-Up Safety Chains Check ChainsOperating Checklist TransportingOperating Check List Cutting InstructionsLeveling Procedure Lift-Type CutterNominal Cutting Height Cutter Height Adjustment Single TailwheelDual Tailwheel Trail-Type Lift SelectionsDeck Attitude Adjustment Lift-TypeTrail-Type Maintenance Service Cutting BladesClutch Run-In Driveline ClutchClutch Assembly and Disassembly StorageLubrication LubricationTailwheel Spindle Tube Tailwheel HubDriveline U-Joints DrivelineRatchet Jack Inner Tube BearingSpecifications and Capacities RCR2584 Rotary CutterTroubleshooting Problem Cause Solution Excessive vibration Torque Values Chart for Common Bolt Sizes 28 RCR2584 Rotary Cutter 312-459M 14/08 Warranty Hydraulic Cylinder One year Parts and LaborCorporate Office P.O. Box 5060 Salina, Kansas 67402-5060 USA
Related manuals
Manual 94 pages 51.59 Kb

RCR2584 specifications

The Land Pride RCR2584 is a robust rotary cutter designed for heavy-duty applications, making it an essential tool for landowners, farmers, and landscapers alike. This rotary cutter is known for its ability to effortlessly tackle thick vegetation, ensuring that properties remain well-maintained and aesthetically pleasing. One of its main features is its cutting width of 84 inches, allowing users to cover large areas in a single pass, thereby saving both time and effort during land management tasks.

Equipped with a powerful gear-driven transmission, the RCR2584 exhibits exceptional durability and strength. This feature is crucial for cutting through tough brush and overgrown grass, as it provides reliable performance even under challenging conditions. The design of the cutter includes a heavy-duty, reinforced frame, which contributes to its robust construction, ensuring that it can withstand the rigors of daily use without compromising performance or safety.

The deck of the RCR2584 features a smooth underside, which prevents grass buildup and enhances the cutter's cutting efficiency. Additionally, this rotary cutter boasts a dual-blade design, allowing for cleaner cuts and improved mulching capabilities. The heavy-duty blade mounts add to the overall durability of the system, ensuring that the blades maintain their position while cutting through dense materials.

For enhanced stability, the RCR2584 includes side skids, which help adjust the cutting height and ensure a smooth, even result across varied terrain. Operators can easily adjust the cutting height as needed, making the cutter versatile for different environments and mowing conditions. Furthermore, the solid 3-point hitch design secures the cutter to tractors, providing a safe and stable connection.

In terms of safety features, the RCR2584 incorporates chain shields that help contain debris, reducing the risk of projectiles while operating. The heavy-duty construction of this rotary cutter not only ensures longevity but also provides peace of mind for operators concerned about safety.

The Land Pride RCR2584 rotary cutter is truly a top-tier solution for those needing reliable land management tools. Its impressive features, advanced technology, and sturdy design make it a valuable investment for maintaining properties and managing landscapes effectively. With this cutter in your arsenal, you can conquer the toughest jobs with confidence.