Land Pride RCR2584 Transporting, Operating Check List, Cutting Instructions, Operating Checklist

Page 17

Land Pride

Table of Contents

Section 2 Operating Instructions

Transporting

!CAUTION!

When traveling on public roads at night or during the day, use accessory lights and devices for adequate warning to opera- tor’s of other vehicles. Comply with all federal, state and local laws.

IMPORTANT: Always disengage the tractor’s PTO before raising the cutter to transport position.

1.When raising the cutter to the transport position be sure that driveline does not contact tractor or cutter.

2.Be sure to reduce tractor ground speed when turning; and, leave enough clearance so the cutter does not contact obstacles such as buildings, trees or fences.

3.Limit transport speed to 20 mph. Transport only with a farm tractor of sufficient size and horse power. When traveling on roadways, transport in such a way that faster moving vehicles may pass you safely.

4.When traveling over rough or hilly terrain, shift tractor to a lower gear.

Operating Check List

In addition to design and configuration of equipment; haz- ard control and accident prevention are dependent upon the awareness, concern, prudence and proper training in- volved in the operation, transport, maintenance and stor- age of equipment. Before beginning to cut, the following inspection should be performed.

!CAUTION!

To prevent personal injury caused by thrown objects, the use of front & rear safety guards is strongly recommended! To avoid injury or death from entanglement in rotating drivelines, the drive gearbox shields must be in place and secure when operat- ing.

!DANGER!

Rotary cutters have the ability to discharge objects at high speeds; therefore, the use of front & rear safety shields is strongly recommended when cutting along highways or in an area where people may be present.

Cutting Instructions

1.Your cutter is equipped with free swinging cutting blades to reduce shock loads to the cutter if striking obstacles.

2.Start the machine slowly; do not use full throttle. Allow 10 seconds for cutter blades to become aligned prop- erly before going to full power.

3.The ground speed depends on two things: the density of the material being cut, and the size of the tractor. Never run fast enough to overload the tractor.

4.It is important to maintain 540 RPM PTO speed. Loss of PTO speed will allow the blades to hinge back and result in ragged, uneven cutting.

5.This cutter was designed to cut grass and medium brush in right-of-ways, pastures and for shredding row crop residues.

Operating Checklist

Check

Reference

“Important Safety Information” in this

Page 1

Manual.

 

 

 

Check oil level in gearboxes.

Section 5

 

Page 22

 

 

Check that all plugs in gearbox have

Section 5

been replaced properly.

Page 22

 

 

Be sure nuts and bolts are tight.

Section 1

 

 

Be certain all guards and shields are in

Section 1

place.

Page 11

 

 

Lubricate the cutter as needed. Refer to

Section 5

“Maintenance and Lubrication”.

Page 22

 

 

!CAUTION!

Damage may occur if exceeding the rated cutting capacity of the cutter!

!CAUTION!

Do not over speed PTO or machine damage may result. This cutter is designed to be used only with a tractor having a 540 RPM rear PTO.

7/14/08

RCR2584 Rotary Cutter 312-459M

15

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Rotary Cutter Operator’st ’s ManuallTable of Contents Keep Riders Off Machinery Be Aware of Signal WordsFor Your Protection Shutdown and StoragePractice Safe Maintenance Use Safety Lights and DevicesPrepare for Emergencies Wear Protective EquipmentTable of Contents 818-130C 818-187C Safety Labels818-552C 818-230C818-540C 838-094C 818-830COwner Assistance Using This ManualPoint Quick Hitch Assembly Point Hitch AssemblyDriveline Installation Tractor RequirementsDual Tailwheel Assembly Single Tailwheel AssemblyTrail-Type Cutter Hitch AssemblyAxle Assembly Safety GuardsRear Chain Guard Front Chain GuardPoint Tractor Hook-Up Tractor Hook-UpTrail-Type Tractor Hook-Up Check Chains Safety ChainsTransporting Operating ChecklistOperating Check List Cutting InstructionsNominal Cutting Height Leveling ProcedureLift-Type Cutter Single Tailwheel Cutter Height AdjustmentTrail-Type Lift Selections Dual TailwheelTrail-Type Deck Attitude AdjustmentLift-Type Service Cutting Blades MaintenanceClutch Run-In Driveline ClutchStorage Clutch Assembly and DisassemblyLubrication LubricationTailwheel Spindle Tube Tailwheel HubDriveline Driveline U-JointsRatchet Jack Inner Tube BearingRCR2584 Rotary Cutter Specifications and CapacitiesTroubleshooting Problem Cause Solution Excessive vibration Torque Values Chart for Common Bolt Sizes 28 RCR2584 Rotary Cutter 312-459M 14/08 Hydraulic Cylinder One year Parts and Labor WarrantyCorporate Office P.O. Box 5060 Salina, Kansas 67402-5060 USA
Related manuals
Manual 94 pages 51.59 Kb

RCR2584 specifications

The Land Pride RCR2584 is a robust rotary cutter designed for heavy-duty applications, making it an essential tool for landowners, farmers, and landscapers alike. This rotary cutter is known for its ability to effortlessly tackle thick vegetation, ensuring that properties remain well-maintained and aesthetically pleasing. One of its main features is its cutting width of 84 inches, allowing users to cover large areas in a single pass, thereby saving both time and effort during land management tasks.

Equipped with a powerful gear-driven transmission, the RCR2584 exhibits exceptional durability and strength. This feature is crucial for cutting through tough brush and overgrown grass, as it provides reliable performance even under challenging conditions. The design of the cutter includes a heavy-duty, reinforced frame, which contributes to its robust construction, ensuring that it can withstand the rigors of daily use without compromising performance or safety.

The deck of the RCR2584 features a smooth underside, which prevents grass buildup and enhances the cutter's cutting efficiency. Additionally, this rotary cutter boasts a dual-blade design, allowing for cleaner cuts and improved mulching capabilities. The heavy-duty blade mounts add to the overall durability of the system, ensuring that the blades maintain their position while cutting through dense materials.

For enhanced stability, the RCR2584 includes side skids, which help adjust the cutting height and ensure a smooth, even result across varied terrain. Operators can easily adjust the cutting height as needed, making the cutter versatile for different environments and mowing conditions. Furthermore, the solid 3-point hitch design secures the cutter to tractors, providing a safe and stable connection.

In terms of safety features, the RCR2584 incorporates chain shields that help contain debris, reducing the risk of projectiles while operating. The heavy-duty construction of this rotary cutter not only ensures longevity but also provides peace of mind for operators concerned about safety.

The Land Pride RCR2584 rotary cutter is truly a top-tier solution for those needing reliable land management tools. Its impressive features, advanced technology, and sturdy design make it a valuable investment for maintaining properties and managing landscapes effectively. With this cutter in your arsenal, you can conquer the toughest jobs with confidence.
Top Page Image Contents