Krell Industries MS 6760 manual Setting Bios Function After AC Power Lost, PM Wake Up Events

Page 48

Setting BIOS Function

After AC Power Lost

This setting specifies whether your system will reboot after a power failure or interrupt occurs. Available settings are:

Off	Leaves the computer in the power off state.
On	Leaves the computer in the power on state.
Last State	Restores the system to the status before power failure or
	interrupt occurred.

PM Wake Up Events

Press <Enter> and the following sub-menu appears.

IRQ [3-7, 9-15], NMI & IRQ 8 Break Suspend

This setting enables/disables the monitoring of the specified IRQ line. If set to Enabled, the activity of the specified IRQ line will prevent the system from entering power saving modes or awaken it from power saving modes. Setting options: Disabled, Enabled.

Wake Up On PME/Ring

These two fields specify whether the system will be awakened from power sav- ings modes when activity or input signal of the specified hardware peripheral or components is detected. Setting options: Disabled, Enabled.

2-21

Image 48

Contents

Mainboard MS 6760 Vers.1 FCC-B Radio Frequency Interference Statement Lithium Battery Statement Macrovision Statement Safety Instructions Copyright Notice Revision Revision History DateContents Control Keys Getting Help System Specification On-Board Headers & Connectors OthersIntroducing Mainboard Introducing MainboardMainboard layout ChapterMS6760 v1.X Mainboard CPU/memory Introduction to DDR SdramPower Supply Power Supply SpecificationFront panel Ieee 1394 Port J1394-2Ieee 1394 Port J1394-1 USB PortsMic-in/Head-Phone Optical SPDIF-inBack panel Serial PortMouse/Keyboard Connectors VGA PortRJ45 LAN Jack Optical SPDIF-outParallel Port Audio Port Connectors IDE Connectors CN22 & CN23FDD Connector CN10 CD-in Connector CN16 TV-Tuner Card Connector CN13CPU Fan Connector CN15 Front Panel Power Connector CN4 USB Card Reader Connector CN6LCM Connector CN8 Modem Module Connector CN21Jumper Clear Cmos Jumper J2Slots PCI SlotAGP Accelerated Graphics Port Slot Setting Bios Function Setting Bios FunctionEntering Setup Control KeysGetting Help Main MenuSub-Menu General Help F1Standard Cmos Features Advanced Bios FeaturesAdvanced Chipset Features Main menuSetting Bios Function Power Management Setup PNP/PCI ConfigurationsLoad Fail/Safe Defaults Load Optimized DefaultsStandard cmos features TimeIDE Primary/Secondary Master/Slave Video Halt OnAdvanced bios features Quick BootBoot Sequence CPU L1 & L2 CacheSetting Bios Function CPU L2 Cache ECC Checking Boot Up Num-Lock StatusTypematic Rate Setting Typematic Delay MsecApic Mode Chapter Security OptionHDD S.M.A.R.T Capability HT CPU FunctionAdvanced chipset features CAS Latency SettingAdvanced Dram Control System PerformanceChapter MA 1T/2T Select AGP Aperture SizeAGP Fast Write Integrated peripherals SIS OnChip IDE DeviceInternal PCI/IDE IDE DMA Transfer Access Chapter IDE Primary/Secondary Master/Slave PIOPrimary/Secondary Master/Slave UltraDMA SIS OnChip PCI DeviceSetting Bios Function USB 2.0 Supports USB Keyboard SupportUSB Mouse Support SIS S/W ModemOnboard Parallel Port Mode Chapter Onboard Super IO DeviceOnboard FDC Controller Onboard Serial Port Setting Bios Function EPP Mode Select ECP Mode Use DMA Init Display First System Share Memory SizeOnboard Lan Boot ROM Chapter Onboard LAN DevicePower management setup Sleep StateChapter Power Management Suspend ModePower Button Function Modem Use IRQSetting Bios Function After AC Power Lost PM Wake Up EventsIRQ 3-7, 9-15, NMI & IRQ 8 Break Suspend Wake Up On PME/RingResume By Alarm Chapter USB Wake Up from S3PS2KB Wake Up from S3/S4/S5 PS2MS Wake Up from S3/S4/S5Pnp/pci configurations Clear EscdResources Controlled By IRQ Resources PCI/VGA Palette SnoopShutdown Temperature PC health statusFrequency/Voltage Control CPU Clock RatioAuto Detect DIMM/PCI Clk Spread SpectrumSetting Bios Function CPU Frequency Dram Frequency