Manuals / Woodstock / Power Tools / Lathe

Woodstock M1109 owner manual Setting Compound Slide, Using the Tool Post

Models: M1109

1 74

Download 74 pages 21.8 Kb

Page 26

M1109 Combo Lathe/Mill

Setting Compound Slide

OPERATIONS

The compound slide is used to cut tapers on parts or to set the proper infeed angle when threading. It may also be used to cut specific lengths longitudinally, when set parallel to the spindle axis.

To set the angular position, do these steps:

1.Loosen the hex nuts, one on each side of the com- pound slide (see Figure 34).

2.Rotate the compound slide to the desired angular position using the scale.

3.Tighten the two hex nuts. Be sure to not overtight- en, as you may strip threads or crack or distort the base casting.

Using the Tool Post

The four-way tool post (Figure 35) is mounted on top of the compound slide, and allows a maximum of four tools to be loaded simultaneously.

The four-way tool post allows for quick indexing to new tools. This is accomplished by rotating the top handle counterclockwise and then rotating the tool post to the desired position. Rotate the top handle clockwise to lock the tool into position.

Hex Nut	Scale

Figure 34. Compound slide, scale, and

handwheel.

Figure 35. Four-way tool post.

-24-

Image 26

Woodstock M1109 owner manual Setting Compound Slide, Using the Tool Post, To set the angular position, do these steps

Contents

Combo LATHE/MILL Page Contents Parts Woodstock Technical Support SpecificationsIntroduction Controls and Features Safety Standard Safety InstructionsSafety Additional Safety Instructions for Lathe/Mills Avoiding Potential Injuries Always protect the bed ways,Extension Cords Electrical220V Operation GroundingPackaged Accessories Figure SetupInstalled Accessories Figure Qty InventoryCleaning Machine Machine PlacementUncrating and Lifting To unpack and move the lathe/mill, do these stepsTest Run and Break-In To begin the test run procedure, do these stepsTroubleshooting on General Power SupplyLathe Operations Disconnect Power to the LATHE/MILL Chuck and Faceplate MountingReplacing Jaws To remove a set of jaws, do these stepsUsing the Four-Jaw Chuck Clamping workpieceUsing the Faceplate Faceplate installedDrilling with the Tailstock Using the TailstockTo install the MT#3 drill chuck, do these steps To use the tailstock, do these stepsTailstock Alignment To setup the tailstock to cut tapers, do these stepsCutting Shallow Tapers With the Tailstock To align the tailstock, do these stepsTailstock adjustment option #2 Using Centers To install a dead or live center, do these stepsTo use the steady rest, do these steps Using the Steady RestUsing the Follow Rest To set the angular position, do these steps Setting Compound SlideUsing the Tool Post Using Manual Feed Longitudinal HandwheelCutting Speeds for High Speed Steel HSS Cutting Tools Setting RPMTo determine and set the needed cutting RPM, do these steps Setting Power Feed Rate Refer to the Change Gear Chart on Page 29, orLoosen the apron lock bolt and use the feed lever Figure Threading SetupTo setup for threading, do these steps Change Gear Chart Milling Operations Installing ToolsTo install a tool in the spindle, do these steps Removing ToolsTo position the spindle head vertically, do these steps Headstock PositioningQuill Travel To use the quill, do these stepsTo begin the start up procedure, do these steps Table TravelHigh speed steel cutting chart General Cleaning MaintenanceGeneral Maintenance General LubricationAdjusting/Replacing the V-Belt To replace or adjust the V-belts, do these stepsCross Slide Backlash ServiceCross Slide, Half-Nut Compound Slide Gib Adjustments Electrical Component and Connection Index M1109 Electrical panelElectrical Connections ContactorTransformer connection Wiring Diagram Lathe controlsTroubleshooting Motor & ElectricalOperation and Work Results Parts Diagram Series Parts List PART# DescriptionThread Dial Diagram 1007 1028SPANNERNUTM16-1.5 Leadscrew Gearbox Diagram 2000 Series Parts Coverplate Compound Rest and Tool Post Diagram FEMALEKNOB5/16-18 Bed Diagram 3000 Series Parts BED Steady Rest and Follow Rest Diagram Pinnedknob Apron Diagram XPK81M Tailstock Diagram STEELBALL8MM Mill Column Diagram XPLW05M LOCKWASHER12MM Headstock Diagram 7000 Series Parts XPR12M EXTRETAININGRING35MM Accessories and Labels Diagram 6THREE-JAWCHUCK Main Wiring Box Diagram Parts Warranty Warranty Registration CommentsBOX BELLINGHAM, WA