Chuck and Faceplate Mounting | Woodstock M1109 specification

M1109 Combo Lathe/Mill

Chuck and Faceplate

Mounting

The three-jaw scroll chuck has hardened steel jaws that self-center the workpiece within 0.002"-0.003". An extra set of jaws is included for machining larger workpieces.

The four-jaw chuck also has hardened steel jaws but are adjusted independently to hold an off-center workpiece. Each jaw can be removed from the chuck body and reversed for special clamping applications.

The cast-iron faceplate has slots for T-bolts that hold clamping fixtures. This face plate and aftermarket clamp- ing hardware will hold non-cylindrical parts such as cast- ings for many types of turning operations.

Both chucks and the faceplate are removed and installed the same way.

To remove and install the chuck or face plate, do these steps:

1.DISCONNECT POWER TO THE LATHE/MILL!

2.Lay a chuck cradle or protective layer of plywood over the bedways to prevent your fingers from being pinched and to protect the precision-ground surfaces (see Figure 15).

3. Use a 14mm wrench and loosen the three hex bolts that secure the chuck to the spindle Figure 16.

4. Support the chuck, and while anticipating the heavy weight of the chuck, remove the three hex bolts and then the chuck.

5. Clean the mating surfaces of the spindle and the new chuck or faceplate with a clean oiled rag.

6. Position the other chuck or faceplate on the spindle flange making sure it is fully seated, and tighten the hex bolts in several alternating sequences.

Securely clamp your workpiece and remove the chuck key! Thrown objects from a lathe/mill can cause serious injury or death to the operator and to bystand- ers many feet away.

-15-

PINCH HAZARD! Protect your hands and precision ground bedways with plywood when removing lathe/mill chuck! The heavy weight of a fall- ing chuck can cause serious injury.

Figure 15. Simple chuck cradle made of

scrap lumber.

Figure 16. Chuck, hex bolts, and spindle

flange.

OPERATIONS

Image 17

Woodstock M1109 owner manual Chuck and Faceplate Mounting, Disconnect Power to the LATHE/MILL

Contents

Combo LATHE/MILL Page Contents Parts Woodstock Technical Support SpecificationsIntroduction Controls and Features Standard Safety Instructions Safety Safety Additional Safety Instructions for Lathe/Mills Always protect the bed ways, Avoiding Potential Injuries 220V Operation ElectricalExtension Cords Grounding Installed Accessories Figure Qty SetupPackaged Accessories Figure Inventory Machine Placement Cleaning Machine To unpack and move the lathe/mill, do these steps Uncrating and Lifting Test Run and Break-In To begin the test run procedure, do these stepsTroubleshooting on General Power SupplyLathe Operations Chuck and Faceplate Mounting Disconnect Power to the LATHE/MILL To remove a set of jaws, do these steps Replacing Jaws Clamping workpiece Using the Four-Jaw Chuck Faceplate installed Using the Faceplate To install the MT#3 drill chuck, do these steps Using the TailstockDrilling with the Tailstock To use the tailstock, do these steps Cutting Shallow Tapers With the Tailstock To setup the tailstock to cut tapers, do these stepsTailstock Alignment To align the tailstock, do these steps Tailstock adjustment option #2 To install a dead or live center, do these steps Using Centers To use the steady rest, do these steps Using the Steady RestUsing the Follow Rest To set the angular position, do these steps Setting Compound SlideUsing the Tool Post Longitudinal Handwheel Using Manual Feed Cutting Speeds for High Speed Steel HSS Cutting Tools Setting RPMTo determine and set the needed cutting RPM, do these steps Refer to the Change Gear Chart on Page 29, or Setting Power Feed Rate Loosen the apron lock bolt and use the feed lever Figure Threading SetupTo setup for threading, do these steps Change Gear Chart To install a tool in the spindle, do these steps Installing ToolsMilling Operations Removing Tools Quill Travel Headstock PositioningTo position the spindle head vertically, do these steps To use the quill, do these steps Table Travel To begin the start up procedure, do these steps High speed steel cutting chart General Maintenance MaintenanceGeneral Cleaning General Lubrication To replace or adjust the V-belts, do these steps Adjusting/Replacing the V-Belt Cross Slide Backlash ServiceCross Slide, Half-Nut Compound Slide Gib Adjustments M1109 Electrical panel Electrical Component and Connection Index Contactor Electrical Connections Transformer connection Lathe controls Wiring Diagram Motor & Electrical Troubleshooting Operation and Work Results Parts Diagram PART# Description Series Parts List 1007 1028 Thread Dial Diagram SPANNERNUTM16-1.5 Leadscrew Gearbox Diagram 2000 Series Parts Coverplate Compound Rest and Tool Post Diagram FEMALEKNOB5/16-18 Bed Diagram 3000 Series Parts BED Steady Rest and Follow Rest Diagram Pinnedknob Apron Diagram XPK81M Tailstock Diagram STEELBALL8MM Mill Column Diagram XPLW05M LOCKWASHER12MM Headstock Diagram 7000 Series Parts XPR12M EXTRETAININGRING35MM Accessories and Labels Diagram 6THREE-JAWCHUCK Main Wiring Box Diagram Parts Warranty Comments Warranty Registration BOX BELLINGHAM, WA