Apron Diagram | Woodstock M1109 specs

M1109 Combo Lathe/Mill

Apron Diagram

(4000 Series Parts)

4038

4039

4040

							4036	4037
							4036						4049
4025	4026	4027	4028	4029			4035				4041		4049
4025	4026	4027	4028	4029		4034	4035				4041		4048
										4042			4048
				4030	4031					4042		4047
				4030	4031			4043	4044	4045		4047
								4043	4044	4045	4046

PARTS

								4032	4033
4024	4023			4022		4021	4020	4019
	4018								4079
	4017					4016
				4015		4016
			4014	4015
	4013		4014
	4013
					4011		4012
				4010	4011
		4009		4010
	4008	4009
	4008
	4007
			4004			4006
		4003	4004					4005
	4002	4003						4005
	4002
	4001

-56-

4050		4051		4052
4050		4051				4062
						4062
4053	4054	4055				4061			4063
			4056	4057		4058			4063
			4056	4057		4058
		4059						4065	4064
		4059	4060				4066	4065
4069			4060			4067	4066
4069
4070
4070	4071					4068
	4071
				4072	4073
					4073
						4074
						4075
						4076
							4077
								4078

Image 58

Woodstock M1109 owner manual Apron Diagram

Contents

Combo LATHE/MILL Page Contents Parts Introduction SpecificationsWoodstock Technical Support Controls and Features Safety Standard Safety Instructions Safety Additional Safety Instructions for Lathe/Mills Avoiding Potential Injuries Always protect the bed ways, Extension Cords Electrical220V Operation Grounding Packaged Accessories Figure SetupInstalled Accessories Figure Qty Inventory Cleaning Machine Machine Placement Uncrating and Lifting To unpack and move the lathe/mill, do these steps Troubleshooting on To begin the test run procedure, do these stepsTest Run and Break-In Lathe Operations Power SupplyGeneral Disconnect Power to the LATHE/MILL Chuck and Faceplate Mounting Replacing Jaws To remove a set of jaws, do these steps Using the Four-Jaw Chuck Clamping workpiece Using the Faceplate Faceplate installed Drilling with the Tailstock Using the TailstockTo install the MT#3 drill chuck, do these steps To use the tailstock, do these steps Tailstock Alignment To setup the tailstock to cut tapers, do these stepsCutting Shallow Tapers With the Tailstock To align the tailstock, do these steps Tailstock adjustment option #2 Using Centers To install a dead or live center, do these steps Using the Follow Rest Using the Steady RestTo use the steady rest, do these steps Using the Tool Post Setting Compound SlideTo set the angular position, do these steps Using Manual Feed Longitudinal Handwheel To determine and set the needed cutting RPM, do these steps Setting RPMCutting Speeds for High Speed Steel HSS Cutting Tools Setting Power Feed Rate Refer to the Change Gear Chart on Page 29, or To setup for threading, do these steps Threading SetupLoosen the apron lock bolt and use the feed lever Figure Change Gear Chart Milling Operations Installing ToolsTo install a tool in the spindle, do these steps Removing Tools To position the spindle head vertically, do these steps Headstock PositioningQuill Travel To use the quill, do these steps To begin the start up procedure, do these steps Table Travel High speed steel cutting chart General Cleaning MaintenanceGeneral Maintenance General Lubrication Adjusting/Replacing the V-Belt To replace or adjust the V-belts, do these steps Cross Slide, Half-Nut Compound Slide Gib Adjustments ServiceCross Slide Backlash Electrical Component and Connection Index M1109 Electrical panel Electrical Connections Contactor Transformer connection Wiring Diagram Lathe controls Troubleshooting Motor & Electrical Operation and Work Results Parts Diagram Series Parts List PART# Description Thread Dial Diagram 1007 1028 SPANNERNUTM16-1.5 Leadscrew Gearbox Diagram 2000 Series Parts Coverplate Compound Rest and Tool Post Diagram FEMALEKNOB5/16-18 Bed Diagram 3000 Series Parts BED Steady Rest and Follow Rest Diagram Pinnedknob Apron Diagram XPK81M Tailstock Diagram STEELBALL8MM Mill Column Diagram XPLW05M LOCKWASHER12MM Headstock Diagram 7000 Series Parts XPR12M EXTRETAININGRING35MM Accessories and Labels Diagram 6THREE-JAWCHUCK Main Wiring Box Diagram Parts Warranty Warranty Registration Comments BOX BELLINGHAM, WA