Controls and Features | Woodstock M1109 instruction

INTRODUCTION

M1109 Combo Lathe/Mill

Controls and Features

				G		I	J
				G			J
		D	F				K
	B		F
A	B			H			L
A	C		E	H			L
			E
							M
AA
Z							N
Z
Y							O
X
							P
							Q
	W		V	U	T
			V
					S	R
			M1109 Combo Lathe/Mill.

A.	Lathe Emergency Stop Button	O.	Feed Rod
B.	Spindle Speed Lever	P.	Chip Tray and Drip Pan
C.	Spindle Range Lever	Q.	Longitudinal and Cross Feed Lever
D.	3-Jaw Chuck	R.	Spindle ON/OFF Rotation Lever
E.	Four-Way Tool Post	S.	Thread Dial
F.	Follow Rest	T.	Half Nut Lever
G.	Milling Speed Levers	U.	Cross Slide Handle
H.	Compound Rest	V.	Manual Feed Hand Wheel
I.	Elevation Handwheel	W.	Storage Cabinet
J.	Mill Power/Emergency Stop Button	X.	Lead Screw Direction Lever
K.	Milling Rack Handles	Y.	Side Cover
L.	Follow Rest	Z.	Jog Button
M.	Tailstock	AA. Power Lamp

N.Lead Screw

-4-

Image 6

Woodstock M1109 owner manual Controls and Features

Contents

Combo LATHE/MILL Page Contents Parts Specifications IntroductionWoodstock Technical Support Controls and Features Safety Standard Safety Instructions Safety Additional Safety Instructions for Lathe/Mills Avoiding Potential Injuries Always protect the bed ways, Extension Cords Electrical220V Operation Grounding Packaged Accessories Figure SetupInstalled Accessories Figure Qty Inventory Cleaning Machine Machine Placement Uncrating and Lifting To unpack and move the lathe/mill, do these steps To begin the test run procedure, do these steps Troubleshooting onTest Run and Break-In Power Supply Lathe OperationsGeneral Disconnect Power to the LATHE/MILL Chuck and Faceplate Mounting Replacing Jaws To remove a set of jaws, do these steps Using the Four-Jaw Chuck Clamping workpiece Using the Faceplate Faceplate installed Drilling with the Tailstock Using the TailstockTo install the MT#3 drill chuck, do these steps To use the tailstock, do these steps Tailstock Alignment To setup the tailstock to cut tapers, do these stepsCutting Shallow Tapers With the Tailstock To align the tailstock, do these steps Tailstock adjustment option #2 Using Centers To install a dead or live center, do these steps Using the Steady Rest Using the Follow RestTo use the steady rest, do these steps Setting Compound Slide Using the Tool PostTo set the angular position, do these steps Using Manual Feed Longitudinal Handwheel Setting RPM To determine and set the needed cutting RPM, do these stepsCutting Speeds for High Speed Steel HSS Cutting Tools Setting Power Feed Rate Refer to the Change Gear Chart on Page 29, or Threading Setup To setup for threading, do these stepsLoosen the apron lock bolt and use the feed lever Figure Change Gear Chart Milling Operations Installing ToolsTo install a tool in the spindle, do these steps Removing Tools To position the spindle head vertically, do these steps Headstock PositioningQuill Travel To use the quill, do these steps To begin the start up procedure, do these steps Table Travel High speed steel cutting chart General Cleaning MaintenanceGeneral Maintenance General Lubrication Adjusting/Replacing the V-Belt To replace or adjust the V-belts, do these steps Service Cross Slide, Half-Nut Compound Slide Gib AdjustmentsCross Slide Backlash Electrical Component and Connection Index M1109 Electrical panel Electrical Connections Contactor Transformer connection Wiring Diagram Lathe controls Troubleshooting Motor & Electrical Operation and Work Results Parts Diagram Series Parts List PART# Description Thread Dial Diagram 1007 1028 SPANNERNUTM16-1.5 Leadscrew Gearbox Diagram 2000 Series Parts Coverplate Compound Rest and Tool Post Diagram FEMALEKNOB5/16-18 Bed Diagram 3000 Series Parts BED Steady Rest and Follow Rest Diagram Pinnedknob Apron Diagram XPK81M Tailstock Diagram STEELBALL8MM Mill Column Diagram XPLW05M LOCKWASHER12MM Headstock Diagram 7000 Series Parts XPR12M EXTRETAININGRING35MM Accessories and Labels Diagram 6THREE-JAWCHUCK Main Wiring Box Diagram Parts Warranty Warranty Registration Comments BOX BELLINGHAM, WA