Electrical, 220V Operation, Extension Cords | Woodstock M1109

M1109 Combo Lathe/Mill

ELECTRICAL

220V Operation

The SHOP FOX® MODEL M1109 Combo Lathe/Mill oper- ates at 220 volt single-phase only. Only connect this machine to a dedicated circuit (wire, breaker, plug, receptacle) with a verified ground, using the recommend- ed circuit size and NEMA 6-20 plug/receptacle (Figure 6) listed at the bottom of this page.

Never replace a circuit breaker with one of higher amper- age without consulting a qualified electrician to ensure compliance with wiring codes. If you are unsure about the wiring codes in your area or plan to connect your machine to a shared circuit, you may create a fire haz- ard—consult a qualified electrician to reduce this risk.

Extension Cords

We do not recommend using an extension cord for 220V operation. When it is necessary to use an extension cord, use the following guidelines:

•Use cords rated for Standard Service

•Never exceed a length of 50 feet

•Ensure cord has a ground wire and pin

•Do not use cords in need of repair

Grounding

This machine must be grounded! Verify that any exist- ing electrical outlet and circuit you intend to plug into is actually grounded. If it is not, it will be necessary to run a separate copper grounding wire, of the appropri- ate size, from the outlet to a known ground. Under no circumstances should you connect your machine to an ungrounded power source or electrocution or severe shock could occur.

DO NOT attempt to work on your electrical system if you are unsure about electrical codes and wiring! Seek assistance from a qualified elec- trician. Ignoring this warning can cause electrocution!

TURN OFF and LOCK your master power switch so no power is available to the lathe/mill before connecting electrical OFF wires! If you ignore this warning serious electrical shock may occur, causing injury or

death!

6-20P6-20R

Figure 6. NEMA 6-20 plug and recepticle.

ELECTRICAL

Operating Voltage	Full Load Amp Draw	Min. Circuit Size	Plug/Receptacle	Extension Cord
220V Single-Phase	17 Amps	20A	NEMA 6-20	12 Gauge

-9-

Image 11

Woodstock M1109 owner manual Electrical, 220V Operation, Extension Cords, Grounding

Contents

Combo LATHE/MILL Page Contents Parts Woodstock Technical Support SpecificationsIntroduction Controls and Features Standard Safety Instructions Safety Safety Additional Safety Instructions for Lathe/Mills Always protect the bed ways, Avoiding Potential Injuries Grounding Electrical220V Operation Extension Cords Inventory SetupInstalled Accessories Figure Qty Packaged Accessories Figure Machine Placement Cleaning Machine To unpack and move the lathe/mill, do these steps Uncrating and Lifting Test Run and Break-In To begin the test run procedure, do these stepsTroubleshooting on General Power SupplyLathe Operations Chuck and Faceplate Mounting Disconnect Power to the LATHE/MILL To remove a set of jaws, do these steps Replacing Jaws Clamping workpiece Using the Four-Jaw Chuck Faceplate installed Using the Faceplate To use the tailstock, do these steps Using the TailstockTo install the MT#3 drill chuck, do these steps Drilling with the Tailstock To align the tailstock, do these steps To setup the tailstock to cut tapers, do these stepsCutting Shallow Tapers With the Tailstock Tailstock Alignment Tailstock adjustment option #2 To install a dead or live center, do these steps Using Centers To use the steady rest, do these steps Using the Steady RestUsing the Follow Rest To set the angular position, do these steps Setting Compound SlideUsing the Tool Post Longitudinal Handwheel Using Manual Feed Cutting Speeds for High Speed Steel HSS Cutting Tools Setting RPMTo determine and set the needed cutting RPM, do these steps Refer to the Change Gear Chart on Page 29, or Setting Power Feed Rate Loosen the apron lock bolt and use the feed lever Figure Threading SetupTo setup for threading, do these steps Change Gear Chart Removing Tools Installing ToolsTo install a tool in the spindle, do these steps Milling Operations To use the quill, do these steps Headstock PositioningQuill Travel To position the spindle head vertically, do these steps Table Travel To begin the start up procedure, do these steps High speed steel cutting chart General Lubrication MaintenanceGeneral Maintenance General Cleaning To replace or adjust the V-belts, do these steps Adjusting/Replacing the V-Belt Cross Slide Backlash ServiceCross Slide, Half-Nut Compound Slide Gib Adjustments M1109 Electrical panel Electrical Component and Connection Index Contactor Electrical Connections Transformer connection Lathe controls Wiring Diagram Motor & Electrical Troubleshooting Operation and Work Results Parts Diagram PART# Description Series Parts List 1007 1028 Thread Dial Diagram SPANNERNUTM16-1.5 Leadscrew Gearbox Diagram 2000 Series Parts Coverplate Compound Rest and Tool Post Diagram FEMALEKNOB5/16-18 Bed Diagram 3000 Series Parts BED Steady Rest and Follow Rest Diagram Pinnedknob Apron Diagram XPK81M Tailstock Diagram STEELBALL8MM Mill Column Diagram XPLW05M LOCKWASHER12MM Headstock Diagram 7000 Series Parts XPR12M EXTRETAININGRING35MM Accessories and Labels Diagram 6THREE-JAWCHUCK Main Wiring Box Diagram Parts Warranty Comments Warranty Registration BOX BELLINGHAM, WA